The DOI matches its Crossref record; 48 of the 48 references it cites were found in a registry or an index.
Bio-ink properties and printability for extrusion printing living cells
Open accessAbstract
Additive biofabrication (3D bioprinting) makes it possible to create scaffolds with precise geometries, control over pore interconnectivity and architectures that are not possible with conventional techniques. Inclusion of cells within the ink to form a "bio-ink" presents the potential to print 3D structures that can be implanted into damaged/diseased tissue to promote highly controlled cell-based regeneration and repair. The properties of an 'ink' are defined by its formulation and critically influence the delivery and integrity of structure formed. Importantly, the ink properties need to conform to biological requirements necessary for the cell system that they are intended to support and it is often challenging to find conditions for printing that facilitate this critical aspect of tissue bioengineering. In this study, alginate (Alg) was selected as the major component of the 'bio-ink' formulations for extrusion printing of cells. The rheological properties of alginate-gelatin (Alg-Gel) blends were compared with pre-crosslinked alginate and alginate solution to establish their printability whilst maintaining their ability to support optimal cell growth. Pre-crosslinked alginate on its own was liquid-like during printing. However, by controlling the temperature, Alg-Gel formulations had higher viscosity, storage modulus and consistency which facilitated higher print resolution/precision. Compression and indentation testing were used to examine the mechanical properties of alginate compared to Alg-Gel. Both types of gels yielded similar results with modulus increasing with alginate concentration. Decay in mechanical properties over time suggests that Alg-Gel slowly degrades in cell culture media with more than 60% decrease in initial modulus over 7 days. The viability of primary myoblasts delivered as a myoblast/Alg-Gel bio-ink was not affected by the printing process, indicating that the Alg-Gel matrix provides a potential means to print 3D constructs that may find application in myoregenerative applications.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Alginate: Properties and biomedical applications
Lee, K. Y., & Mooney, D. J. (2012) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2011.06.003 · Cited by 8,095
Hydrogels for Tissue Engineering
Lee, K. Y., & Mooney, D. J. (2001) · Chemical Reviews · doi:10.1021/cr000108x · Cited by 5,277
Scaffolds in tissue engineering bone and cartilage
Hutmacher, D. W. (2000) · Biomaterials · doi:10.1016/s0142-9612(00)00121-6 · Cited by 4,994
Alginate hydrogels as synthetic extracellular matrix materials
Rowley, J. A., Madlambayan, G., & Mooney, D. J. (1999) · Biomaterials · doi:10.1016/s0142-9612(98)00107-0 · Cited by 2,342
Alginate Hydrogels as Biomaterials
Augst, A. D., Kong, H. J., & Mooney, D. J. (2006) · Macromolecular Bioscience · doi:10.1002/mabi.200600069 · Cited by 1,839
Kuo, C. K., & Ma, P. X. (2001) · Biomaterials · doi:10.1016/s0142-9612(00)00201-5 · Cited by 1,491
Molecular and Cellular Endocrinology
Rainey, W., & Rodgers, R. (2004) · Molecular and Cellular Endocrinology · doi:10.1016/j.mce.2004.10.007 · Cited by 1,307
Department of Materials, U. O. O., Sachlos, E., & Czernuszka, J. (2003) · European Cells and Materials · doi:10.22203/ecm.v005a03 · Cited by 1,303
A review of trends and limitations in hydrogel-rapid prototyping for tissue engineering
Billiet, T., Vandenhaute, M., Schelfhout, J., Van Vlierberghe, S., & Dubruel, P. (2012) · Biomaterials · doi:10.1016/j.biomaterials.2012.04.050 · Cited by 1,284
Evaluation of an in situ forming hydrogel wound dressing based on oxidized alginate and gelatin
Balakrishnan, B., Mohanty, M., Umashankar, P. R., & Jayakrishnan, A. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2005.04.012 · Cited by 959
Cited by
Current advances and future perspectives in extrusion-based bioprinting
Ozbolat, I. T., & Hospodiuk, M. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2015.10.076 · Cited by 1,572
Markstedt, K., Mantas, A., Tournier, I., Martínez Ávila, H., Hägg, D., & Gatenholm, P. (2015) · Biomacromolecules · doi:10.1021/acs.biomac.5b00188 · Cited by 1,528
Printability and shape fidelity of bioinks in 3D bioprinting
Schwab, A., Levato, R., D’Este, M., Piluso, S., Eglin, D., & Malda, J. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00084 · Cited by 1,359
Bioink properties before, during and after 3D bioprinting
Hölzl, K., Lin, S., Tytgat, L., Van Vlierberghe, S., Gu, L., & Ovsianikov, A. (2016) · Biofabrication · doi:10.1088/1758-5090/8/3/032002 · Cited by 1,070
Ouyang, L., Yao, R., Zhao, Y., & Sun, W. (2016) · Biofabrication · doi:10.1088/1758-5090/8/3/035020 · Cited by 1,045
Paxton, N., Smolan, W., Böck, T., Melchels, F., Groll, J., & Jungst, T. (2017) · Biofabrication · doi:10.1088/1758-5090/aa8dd8 · Cited by 950
Wound Healing: From Passive to Smart Dressings
Farahani, M., & Shafiee, A. (2021) · Advanced Healthcare Materials · doi:10.1002/adhm.202100477 · Cited by 794
Li, Y., Gao, T., Yang, Z., Chen, C., Luo, W., Song, J., Hitz, E., Jia, C., Zhou, Y., Liu, B., et al. (2017) · Advanced Materials · doi:10.1002/adma.201700981 · Cited by 720
3D Bioprinting for Tissue and Organ Fabrication
Zhang, Y. S., Yue, K., Aleman, J., Mollazadeh-Moghaddam, K., Bakht, S. M., Yang, J., Jia, W., Dell’Erba, V., Assawes, P., Shin, S. R., et al. (2017) · Annals of Biomedical Engineering · doi:10.1007/s10439-016-1612-8 · Cited by 682
Advanced Bioinks for 3D Printing: A Materials Science Perspective
Chimene, D., Lennox, K. K., Kaunas, R. R., & Gaharwar, A. K. (2016) · Annals of Biomedical Engineering · doi:10.1007/s10439-016-1638-y · Cited by 679
Applications of Alginate-Based Bioinks in 3D Bioprinting
Axpe, E., & Oyen, M. (2016) · International Journal of Molecular Sciences · doi:10.3390/ijms17121976 · Cited by 663
Research on the printability of hydrogels in 3D bioprinting
He, Y., Yang, F., Zhao, H., Gao, Q., Xia, B., & Fu, J. (2016) · Scientific Reports · doi:10.1038/srep29977 · Cited by 654
Yin, J., Yan, M., Wang, Y., Fu, J., & Suo, H. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b16059 · Cited by 598
Review of alginate-based hydrogel bioprinting for application in tissue engineering
Rastogi, P., & Kandasubramanian, B. (2019) · Biofabrication · doi:10.1088/1758-5090/ab331e · Cited by 564
Alginate hydrogels for bone tissue engineering, from injectables to bioprinting: A review
Hernández-González, A. C., Téllez-Jurado, L., & Rodríguez-Lorenzo, L. M. (2020) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2019.115514 · Cited by 549
Engineering alginate as bioink for bioprinting
Jia, J., Richards, D. J., Pollard, S., Tan, Y., Rodriguez, J., Visconti, R. P., Trusk, T. C., Yost, M. J., Yao, H., Markwald, R. R., et al. (2014) · Acta Biomaterialia · doi:10.1016/j.actbio.2014.06.034 · Cited by 549
Bioinks and bioprinting technologies to make heterogeneous and biomimetic tissue constructs
Ashammakhi, N., Ahadian, S., Xu, C., Montazerian, H., Ko, H., Nasiri, R., Barros, N., & Khademhosseini, A. (2019) · Materials Today Bio · doi:10.1016/j.mtbio.2019.100008 · Cited by 549
Yang, X., Lu, Z., Wu, H., Li, W., Zheng, L., & Zhao, J. (2018) · Materials Science and Engineering: C · doi:10.1016/j.msec.2017.09.002 · Cited by 533
Liu, Z., Bhandari, B., Prakash, S., Mantihal, S., & Zhang, M. (2019) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2018.08.026 · Cited by 530
Gao, T., Gillispie, G. J., Copus, J. S., PR, A. K., Seol, Y.-J., Atala, A., Yoo, J. J., & Lee, S. J. (2018) · Biofabrication · doi:10.1088/1758-5090/aacdc7 · Cited by 510
‘Printability' of Candidate Biomaterials for Extrusion Based 3D Printing: State‐of‐the‐Art
Kyle, S., Jessop, Z. M., Al‐Sabah, A., & Whitaker, I. S. (2017) · Advanced Healthcare Materials · doi:10.1002/adhm.201700264 · Cited by 495
Scaffolding Strategies for Tissue Engineering and Regenerative Medicine Applications
Pina, S., Ribeiro, V. P., Marques, C. F., Maia, F. R., Silva, T. H., Reis, R. L., & Oliveira, J. M. (2019) · Materials · doi:10.3390/ma12111824 · Cited by 493
An Introduction to 3D Bioprinting: Possibilities, Challenges and Future Aspects
Kačarević, Ž. P., Rider, P. M., Alkildani, S., Retnasingh, S., Smeets, R., Jung, O., Ivanišević, Z., & Barbeck, M. (2018) · Materials · doi:10.3390/ma11112199 · Cited by 479
Assessing bioink shape fidelity to aid material development in 3D bioprinting
Ribeiro, A., Blokzijl, M. M., Levato, R., Visser, C. W., Castilho, M., Hennink, W. E., Vermonden, T., & Malda, J. (2017) · Biofabrication · doi:10.1088/1758-5090/aa90e2 · Cited by 448
Current advances and future perspectives of 3D printing natural-derived biopolymers
Liu, J., Sun, L., Xu, W., Wang, Q., Yu, S., & Sun, J. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2018.11.077 · Cited by 428
Bioprinting Technology: A Current State-of-the-Art Review
Dababneh, A. B., & Ozbolat, I. T. (2014) · Journal of Manufacturing Science and Engineering · doi:10.1115/1.4028512 · Cited by 427
Assessment methodologies for extrusion-based bioink printability
Gillispie, G., Prim, P., Copus, J., Fisher, J., Mikos, A. G., Yoo, J. J., Atala, A., & Lee, S. J. (2020) · Biofabrication · doi:10.1088/1758-5090/ab6f0d · Cited by 426
Li, Y., Gao, T., Yang, Z., Chen, C., Kuang, Y., Song, J., Jia, C., Hitz, E. M., Yang, B., & Hu, L. (2017) · Nano Energy · doi:10.1016/j.nanoen.2017.09.034 · Cited by 416
Poloxamer Hydrogels for Biomedical Applications
Russo, E., & Villa, C. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11120671 · Cited by 408
Crosslinking Strategies for 3D Bioprinting of Polymeric Hydrogels
GhavamiNejad, A., Ashammakhi, N., Wu, X. Y., & Khademhosseini, A. (2020) · Small · doi:10.1002/smll.202002931 · Cited by 400
Mechanical behaviour of alginate-gelatin hydrogels for 3D bioprinting
Giuseppe, M. D., Law, N., Webb, B., A. Macrae, R., Liew, L. J., Sercombe, T. B., Dilley, R. J., & Doyle, B. J. (2018) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2017.12.018 · Cited by 394
Naturally sourced hydrogels: emerging fundamental materials for next-generation healthcare sensing
Wang, Z., Wei, H., Huang, Y., Wei, Y., & Chen, J. (2023) · Chemical Society Reviews · doi:10.1039/d2cs00813k · Cited by 392
Li, Y.-C., Zhang, Y. S., Akpek, A., Shin, S. R., & Khademhosseini, A. (2016) · Biofabrication · doi:10.1088/1758-5090/9/1/012001 · Cited by 385
Functional 3D Neural Mini‐Tissues from Printed Gel‐Based Bioink and Human Neural Stem Cells
Gu, Q., Tomaskovic‐Crook, E., Lozano, R., Chen, Y., Kapsa, R. M., Zhou, Q., Wallace, G. G., & Crook, J. M. (2016) · Advanced Healthcare Materials · doi:10.1002/adhm.201600095 · Cited by 376
Self-citationA bioprintable form of chitosan hydrogel for bone tissue engineering
Demirtaş, T. T., Irmak, G., & Gümüşderelioğlu, M. (2017) · Biofabrication · doi:10.1088/1758-5090/aa7b1d · Cited by 376
Shear-Thinning and Thermo-Reversible Nanoengineered Inks for 3D Bioprinting
Wilson, S. A., Cross, L. M., Peak, C. W., & Gaharwar, A. K. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b13602 · Cited by 369
Askari, M., Afzali Naniz, M., Kouhi, M., Saberi, A., Zolfagharian, A., & Bodaghi, M. (2021) · Biomaterials Science · doi:10.1039/d0bm00973c · Cited by 369
Gao, F., Xu, Z., Liang, Q., Liu, B., Li, H., Wu, Y., Zhang, Y., Lin, Z., Wu, M., Ruan, C., et al. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201706644 · Cited by 330
Bendtsen, S. T., Quinnell, S. P., & Wei, M. (2017) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.36036 · Cited by 329
3D printing with cellulose materials
Wang, Q., Sun, J., Yao, Q., Ji, C., Liu, J., & Zhu, Q. (2018) · Cellulose · doi:10.1007/s10570-018-1888-y · Cited by 324
Gelatin-Based Hydrogels for Organ 3D Bioprinting
Wang, X., Ao, Q., Tian, X., Fan, J., Tong, H., Hou, W., & Bai, S. (2017) · Polymers · doi:10.3390/polym9090401 · Cited by 315
In situ handheld three‐dimensional bioprinting for cartilage regeneration
Di Bella, C., Duchi, S., O'Connell, C. D., Blanchard, R., Augustine, C., Yue, Z., Thompson, F., Richards, C., Beirne, S., Onofrillo, C., et al. (2018) · Journal of Tissue Engineering and Regenerative Medicine · doi:10.1002/term.2476 · Cited by 313
Self-citationChen, H., Xie, F., Chen, L., & Zheng, B. (2019) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2018.09.011 · Cited by 301
3D Bioprinting in Skeletal Muscle Tissue Engineering
Ostrovidov, S., Salehi, S., Costantini, M., Suthiwanich, K., Ebrahimi, M., Sadeghian, R. B., Fujie, T., Shi, X., Cannata, S., Gargioli, C., et al. (2019) · Small · doi:10.1002/smll.201805530 · Cited by 294
Kesti, M., Müller, M., Becher, J., Schnabelrauch, M., D’Este, M., Eglin, D., & Zenobi-Wong, M. (2015) · Acta Biomaterialia · doi:10.1016/j.actbio.2014.09.033 · Cited by 294
3D printed scaffolds with gradient porosity based on a cellulose nanocrystal hydrogel
Sultan, S., & Mathew, A. P. (2018) · Nanoscale · doi:10.1039/c7nr08966j · Cited by 285
The rheology of direct and suspended extrusion bioprinting
Cooke, M. E., & Rosenzweig, D. H. (2021) · APL Bioengineering · doi:10.1063/5.0031475 · Cited by 284
Natural Hydrogel-Based Bio-Inks for 3D Bioprinting in Tissue Engineering: A Review
Fatimi, A., Okoro, O. V., Podstawczyk, D., Siminska-Stanny, J., & Shavandi, A. (2022) · Gels · doi:10.3390/gels8030179 · Cited by 276
Printability–A key issue in extrusion-based bioprinting
Naghieh, S., & Chen, X. (2021) · Journal of Pharmaceutical Analysis · doi:10.1016/j.jpha.2021.02.001 · Cited by 270
Physical and Chemical Factors Influencing the Printability of Hydrogel-based Extrusion Bioinks
Lee, S. C., Gillispie, G., Prim, P., & Lee, S. J. (2020) · Chemical Reviews · doi:10.1021/acs.chemrev.0c00015 · Cited by 255
Natural Polymers for Organ 3D Bioprinting
Liu, F., Chen, Q., Liu, C., Ao, Q., Tian, X., Fan, J., Tong, H., & Wang, X. (2018) · Polymers · doi:10.3390/polym10111278 · Cited by 170
Stepanovska, J., Supova, M., Hanzalek, K., Broz, A., & Matejka, R. (2021) · Biomedicines · doi:10.3390/biomedicines9091137 · Cited by 112
Sarker, M., Izadifar, M., Schreyer, D., & Chen, X. (2018) · Journal of Biomaterials Science, Polymer Edition · doi:10.1080/09205063.2018.1433420 · Cited by 109
Modeling a dynamic printability window on polysaccharide blend inks for extrusion bioprinting
Perin, F., Spessot, E., Famà, A., Bucciarelli, A., Callone, E., Mota, C., Motta, A., & Maniglio, D. (2023) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.2c01143 · Cited by 33
In vitro 3D skin culture and its sustainability in toxicology: a narrative review
Masri, S., Fauzi, M. B., Rajab, N. F., Lee, W.-H., Zainal Abidin, D. A., & Siew, E. L. (2024) · Artificial Cells, Nanomedicine, and Biotechnology · doi:10.1080/21691401.2024.2407617 · Cited by 15
Metadata
- Authors
- Chung, J. H. Y., Naficy, S., Yue, Z., Kapsa, R., Quigley, A., Moulton, S. E., & Wallace, G. G.
- Venue
- Biomaterials Science
- Publisher
- Royal Society of Chemistry (RSC)
- Published
- 2013
- Volume
- 1
- Issue
- 7
- Pages
- 763
- ISSN
- 2047-4830 (ISSN-L)
- 2047-4849
- OpenAlex
- W2171492615
- Cited by
- 610
- References
- 48
- FWCI
- 8.15
- Type
- journal article
- Language
- en
- Open access
- bronze
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.