Polymers for Extrusion-Based 3D Printing of Pharmaceuticals: A Holistic Materials–Process Perspective
Open accessThe DOI matches its Crossref record; 172 of the 176 references it cites were found in a registry or an index.
Abstract
Three dimensional (3D) printing as an advanced manufacturing technology is progressing to be established in the pharmaceutical industry to overcome the traditional manufacturing regime of 'one size fits for all'. Using 3D printing, it is possible to design and develop complex dosage forms that can be suitable for tuning drug release. Polymers are the key materials that are necessary for 3D printing. Among all 3D printing processes, extrusion-based (both fused deposition modeling (FDM) and pressure-assisted microsyringe (PAM)) 3D printing is well researched for pharmaceutical manufacturing. It is important to understand which polymers are suitable for extrusion-based 3D printing of pharmaceuticals and how their properties, as well as the behavior of polymer–active pharmaceutical ingredient (API) combinations, impact the printing process. Especially, understanding the rheology of the polymer and API–polymer mixtures is necessary for successful 3D printing of dosage forms or printed structures. This review has summarized a holistic materials–process perspective for polymers on extrusion-based 3D printing. The main focus herein will be both FDM and PAM 3D printing processes. It elaborates the discussion on the comparison of 3D printing with the traditional direct compression process, the necessity of rheology, and the characterization techniques required for the printed structure, drug, and excipients. The current technological challenges, regulatory aspects, and the direction toward which the technology is moving, especially for personalized pharmaceuticals and multi-drug printing, are also briefly discussed.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Figures






![Figure 7 Viscosity ratio (η/ηo) of acetaminophen (APAP) in poly (ethylene oxide) (PEO) at different temperatures to determine the solubility of the drug. Reprinted with permission from M Yang, International Journal of Pharmaceutics, Published by Elsevier, 2011 [123].](https://figures.cochat.ai/paper-figures/5b0f2d6634994ae79cc2c2cbcb3eb075/polymers-for-extrusion-based-3d-printing-of-pharmaceuticals-a-holistic-figure-7.jpg)
![Figure 8 The rheological characterization of the blends of different polymers [Affinisol 15LV (Aff15), Kollidon SR (KollSR), Eudragit EPO (EPO), hydroxypropyl cellulose (HPC)]. Constituent effect visualized with frequency sweep at the maximum processing temperature (200 °C). Reprinted with permission from K Ilyés, European Journal of Pharmaceutical Sciences, Published by Elsevier, 2019 [136].](https://figures.cochat.ai/paper-figures/b1ca4ae8602d4e64bbc6cbb3bfa0f28d/polymers-for-extrusion-based-3d-printing-of-pharmaceuticals-a-holistic-figure-8.jpg)

![Figure 10 (a) Design of tablets, (b) the relationship between the target and achieved prednisolone dose, and (c) PVA based FDM 3D printed tablets having different dose strengths [56].](https://figures.cochat.ai/paper-figures/76d1606acd2449ce8e030af1e4501a72/polymers-for-extrusion-based-3d-printing-of-pharmaceuticals-a-holistic-figure-10.jpg)
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
The source backs part of the claim, not all of it — or backs it for a different population, condition or comparison.
In the citing paper
“3D printing enables the fabrication of complex three-dimensional structures via computer-aided design, allows precise control over scaffold porosity, pore size, and microstructure, and facilitates accurate modulation of mechanical strength, and creates microstructures with graded porosity within a single scaffold [88–90].”
From Application of PLCL as a biodegradable polymer in biomedical engineering (2026) · cites this paper as [88]
Experimental — accuracy not yet measured
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Polymers for 3D Printing and Customized Additive Manufacturing
Ligon, S. C., Liska, R., Stampfl, J., Gurr, M., & Mülhaupt, R. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.7b00074 · Cited by 3,741
Farah, S., Anderson, D. G., & Langer, R. (2016) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.06.012 · Cited by 3,443
Modeling of drug release from delivery systems based on hydroxypropyl methylcellulose (HPMC)
Siepmann, J. (2001) · Advanced Drug Delivery Reviews · doi:10.1016/s0169-409x(01)00112-0 · Cited by 2,613
Biomedical applications of biodegradable polymers
Ulery, B. D., Nair, L. S., & Laurencin, C. T. (2011) · Journal of Polymer Science Part B: Polymer Physics · doi:10.1002/polb.22259 · Cited by 2,206
Correlation of dynamic and steady flow viscosities
Cox, W. P., & Merz, E. H. (1958) · Journal of Polymer Science · doi:10.1002/pol.1958.1202811812 · Cited by 2,092
Personalized medicine: Time for one-person trials
Schork, N. J. (2015) · Nature · doi:10.1038/520609a · Cited by 1,223
Modeling of drug release from delivery systems based on hydroxypropyl methylcellulose (HPMC)
Siepmann, J., & Peppas, N. A. (2012) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2012.09.028 · Cited by 1,021
Awaja, F., Gilbert, M., Kelly, G., Fox, B., & Pigram, P. J. (2009) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2009.04.007 · Cited by 928
Three-Dimensional Printing: Rapid Tooling and Prototypes Directly from a CAD Model
Sachs, E., Cima, M., & Cornie, J. (1990) · CIRP Annals · doi:10.1016/s0007-8506(07)61035-x · Cited by 871
A new chapter in pharmaceutical manufacturing: 3D-printed drug products
Norman, J., Madurawe, R. D., Moore, C. M. V., Khan, M. A., & Khairuzzaman, A. (2017) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.03.001 · Cited by 810
3D Printing in Pharmaceutical and Medical Applications – Recent Achievements and Challenges
Jamróz, W., Szafraniec, J., Kurek, M., & Jachowicz, R. (2018) · Pharmaceutical Research · doi:10.1007/s11095-018-2454-x · Cited by 707
The Role of 3D Printing in Medical Applications: A State of the Art
Aimar, A., Palermo, A., & Innocenti, B. (2019) · Journal of Healthcare Engineering · doi:10.1155/2019/5340616 · Cited by 685
Effect of geometry on drug release from 3D printed tablets
Goyanes, A., Robles Martinez, P., Buanz, A., Basit, A. W., & Gaisford, S. (2015) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2015.04.069 · Cited by 667
3D printing in pharmaceutics: A new tool for designing customized drug delivery systems
Goole, J., & Amighi, K. (2016) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2015.12.071 · Cited by 660
Stereolithographic (SLA) 3D printing of oral modified-release dosage forms
Wang, J., Goyanes, A., Gaisford, S., & Basit, A. W. (2016) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2016.03.016 · Cited by 612
Khaled, S. A., Burley, J. C., Alexander, M. R., Yang, J., & Roberts, C. J. (2015) · Journal of Controlled Release · doi:10.1016/j.jconrel.2015.09.028 · Cited by 606
Current and emerging applications of 3D printing in medicine
Liaw, C.-Y., & Guvendiren, M. (2017) · Biofabrication · doi:10.1088/1758-5090/aa7279 · Cited by 604
Fused-filament 3D printing (3DP) for fabrication of tablets
Goyanes, A., Buanz, A. B. M., Basit, A. W., & Gaisford, S. (2014) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2014.09.044 · Cited by 587
Selective laser sintering (SLS) 3D printing of medicines
Fina, F., Goyanes, A., Gaisford, S., & Basit, A. W. (2017) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2017.06.082 · Cited by 577
Three Dimensional Printing: Rapid Tooling and Prototypes Directly from a CAD Model
Sachs, E., Cima, M., Williams, P., Brancazio, D., & Cornie, J. (1992) · Journal of Engineering for Industry · doi:10.1115/1.2900701 · Cited by 573
3D printing of modified-release aminosalicylate (4-ASA and 5-ASA) tablets
Goyanes, A., Buanz, A. B. M., Hatton, G. B., Gaisford, S., & Basit, A. W. (2015) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2014.12.003 · Cited by 570
Polymers of N-Vinylpyrrolidone: Synthesis, Characterization and Uses
Haaf, F., Sanner, A., & Straub, F. (1985) · Polymer Journal · doi:10.1295/polymj.17.143 · Cited by 561
Emergence of 3D Printed Dosage Forms: Opportunities and Challenges
Alhnan, M. A., Okwuosa, T. C., Sadia, M., Wan, K.-W., Ahmed, W., & Arafat, B. (2016) · Pharmaceutical Research · doi:10.1007/s11095-016-1933-1 · Cited by 554
Skowyra, J., Pietrzak, K., & Alhnan, M. A. (2015) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2014.11.009 · Cited by 530
Desktop 3D printing of controlled release pharmaceutical bilayer tablets
Khaled, S. A., Burley, J. C., Alexander, M. R., & Roberts, C. J. (2014) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2013.11.021 · Cited by 511
Goyanes, A., Wang, J., Buanz, A., Martínez-Pacheco, R., Telford, R., Gaisford, S., & Basit, A. W. (2015) · Molecular Pharmaceutics · doi:10.1021/acs.molpharmaceut.5b00510 · Cited by 511
3D printing of tablets containing multiple drugs with defined release profiles
Khaled, S. A., Burley, J. C., Alexander, M. R., Yang, J., & Roberts, C. J. (2015) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2015.07.067 · Cited by 508
Direct writing in three dimensions
Lewis, J. A., & Gratson, G. M. (2004) · Materials Today · doi:10.1016/s1369-7021(04)00344-x · Cited by 507
Goyanes, A., Det-Amornrat, U., Wang, J., Basit, A. W., & Gaisford, S. (2016) · Journal of Controlled Release · doi:10.1016/j.jconrel.2016.05.034 · Cited by 490
Eudragit®: a technology evaluation
Thakral, S., Thakral, N. K., & Majumdar, D. K. (2013) · Expert Opinion on Drug Delivery · doi:10.1517/17425247.2013.736962 · Cited by 458
Personalized medicine: revolutionizing drug discovery and patient care
Ginsburg, G. (2001) · Trends in Biotechnology · doi:10.1016/s0167-7799(01)01814-5 · Cited by 456
3D Printing technologies for drug delivery: a review
Prasad, L. K., & Smyth, H. (2016) · Drug Development and Industrial Pharmacy · doi:10.3109/03639045.2015.1120743 · Cited by 454
Recent Developments in Fused Deposition Modeling-Based 3D Printing of Polymers and Their Composites
Rahim, T. N. A. T., Abdullah, A. M., & Md Akil, H. (2019) · Polymer Reviews · doi:10.1080/15583724.2019.1597883 · Cited by 452
Recent developments in biodegradable synthetic polymers
Gunatillake, P., Mayadunne, R., & Adhikari, R. (2006) · Biotechnology Annual Review · doi:10.1016/s1387-2656(06)12009-8 · Cited by 444
Melocchi, A., Parietti, F., Maroni, A., Foppoli, A., Gazzaniga, A., & Zema, L. (2016) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2016.05.036 · Cited by 409
A flexible-dose dispenser for immediate and extended release 3D printed tablets
Pietrzak, K., Isreb, A., & Alhnan, M. A. (2015) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2015.07.027 · Cited by 407
Coupling 3D printing with hot-melt extrusion to produce controlled-release tablets
Zhang, J., Feng, X., Patil, H., Tiwari, R. V., & Repka, M. A. (2017) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2016.12.049 · Cited by 393
Solid free-form fabrication of drug delivery devices
Wu, B. M., Borland, S. W., Giordano, R. A., Cima, L. G., Sachs, E. M., & Cima, M. J. (1996) · Journal of Controlled Release · doi:10.1016/0168-3659(95)00173-5 · Cited by 361
3D Printing of a Multi-Layered Polypill Containing Six Drugs Using a Novel Stereolithographic Method
Robles-Martinez, P., Xu, X., Trenfield, S. J., Awad, A., Goyanes, A., Telford, R., Basit, A. W., & Gaisford, S. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11060274 · Cited by 358
Goyanes, A., Fina, F., Martorana, A., Sedough, D., Gaisford, S., & Basit, A. W. (2017) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2017.05.021 · Cited by 355
The use of hypromellose in oral drug delivery
Li, C. L., Martini, L. G., Ford, J. L., & Roberts, M. (2005) · Journal of Pharmacy and Pharmacology · doi:10.1211/0022357055957 · Cited by 340
Fabrication of controlled-release budesonide tablets via desktop (FDM) 3D printing
Goyanes, A., Chang, H., Sedough, D., Hatton, G. B., Wang, J., Buanz, A., Gaisford, S., & Basit, A. W. (2015) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2015.10.039 · Cited by 330
Tan, D. K., Maniruzzaman, M., & Nokhodchi, A. (2018) · Pharmaceutics · doi:10.3390/pharmaceutics10040203 · Cited by 329
Sadia, M., Sośnicka, A., Arafat, B., Isreb, A., Ahmed, W., Kelarakis, A., & Alhnan, M. A. (2016) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2016.09.050 · Cited by 323
Low temperature fused deposition modeling (FDM) 3D printing of thermolabile drugs
Kollamaram, G., Croker, D. M., Walker, G. M., Goyanes, A., Basit, A. W., & Gaisford, S. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.04.055 · Cited by 318
3D printing for chemical, pharmaceutical and biological applications
Capel, A. J., Rimington, R. P., Lewis, M. P., & Christie, S. D. R. (2018) · Nature Reviews Chemistry · doi:10.1038/s41570-018-0058-y · Cited by 312
Personalised 3D Printed Medicines: Which Techniques and Polymers Are More Successful?
Konta, A., García-Piña, M., & Serrano, D. (2017) · Bioengineering · doi:10.3390/bioengineering4040079 · Cited by 301
Fabricating 3D printed orally disintegrating printlets using selective laser sintering
Fina, F., Madla, C. M., Goyanes, A., Zhang, J., Gaisford, S., & Basit, A. W. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.02.015 · Cited by 300
Melocchi, A., Parietti, F., Loreti, G., Maroni, A., Gazzaniga, A., & Zema, L. (2015) · Journal of Drug Delivery Science and Technology · doi:10.1016/j.jddst.2015.07.016 · Cited by 299
Okwuosa, T. C., Stefaniak, D., Arafat, B., Isreb, A., Wan, K.-W., & Alhnan, M. A. (2016) · Pharmaceutical Research · doi:10.1007/s11095-016-1995-0 · Cited by 294
Kyobula, M., Adedeji, A., Alexander, M. R., Saleh, E., Wildman, R., Ashcroft, I., Gellert, P. R., & Roberts, C. J. (2017) · Journal of Controlled Release · doi:10.1016/j.jconrel.2017.06.025 · Cited by 288
Okwuosa, T. C., Pereira, B. C., Arafat, B., Cieszynska, M., Isreb, A., & Alhnan, M. A. (2017) · Pharmaceutical Research · doi:10.1007/s11095-016-2073-3 · Cited by 277
Solanki, N. G., Tahsin, M., Shah, A. V., & Serajuddin, A. T. M. (2018) · Journal of Pharmaceutical Sciences · doi:10.1016/j.xphs.2017.10.021 · Cited by 272
Kadry, H., Wadnap, S., Xu, C., & Ahsan, F. (2019) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2019.05.008 · Cited by 265
Schiele, J. T., Quinzler, R., Klimm, H.-D., Pruszydlo, M. G., & Haefeli, W. E. (2013) · European Journal of Clinical Pharmacology · doi:10.1007/s00228-012-1417-0 · Cited by 264
Personalised dosing: Printing a dose of one’s own medicine
Alomari, M., Mohamed, F. H., Basit, A. W., & Gaisford, S. (2015) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2014.12.006 · Cited by 257
Multimechanism oral dosage forms fabricated by three dimensional printing™
Rowe, C. W., Katstra, W. E., Palazzolo, R. D., Giritlioglu, B., Teung, P., & Cima, M. J. (2000) · Journal of Controlled Release · doi:10.1016/s0168-3659(99)00224-2 · Cited by 255
3D printed drug delivery and testing systems — a passing fad or the future?
Lim, S. H., Kathuria, H., Tan, J. J. Y., & Kang, L. (2018) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2018.05.006 · Cited by 252
Goyanes, A., Kobayashi, M., Martínez-Pacheco, R., Gaisford, S., & Basit, A. W. (2016) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2016.06.021 · Cited by 247
Direct powder extrusion 3D printing: Fabrication of drug products using a novel single-step process
Goyanes, A., Allahham, N., Trenfield, S. J., Stoyanov, E., Gaisford, S., & Basit, A. W. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.118471 · Cited by 246
Vithani, K., Goyanes, A., Jannin, V., Basit, A. W., Gaisford, S., & Boyd, B. J. (2019) · Pharmaceutical Research · doi:10.1007/s11095-018-2531-1 · Cited by 233
3D Printed Pellets (Miniprintlets): A Novel, Multi-Drug, Controlled Release Platform Technology
Awad, A., Fina, F., Trenfield, S. J., Patel, P., Goyanes, A., Gaisford, S., & Basit, A. W. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11040148 · Cited by 229
3D Printing Gets a Boost and Opportunities with Polymer Materials
Hofmann, M. (2014) · ACS Macro Letters · doi:10.1021/mz4006556 · Cited by 225
Preparation and investigation of novel gastro-floating tablets with 3D extrusion-based printing
Li, Q., Guan, X., Cui, M., Zhu, Z., Chen, K., Wen, H., Jia, D., Hou, J., Xu, W., Yang, X., et al. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2017.10.037 · Cited by 222
3D extrusion printing of high drug loading immediate release paracetamol tablets
Khaled, S. A., Alexander, M. R., Wildman, R. D., Wallace, M. J., Sharpe, S., Yoo, J., & Roberts, C. J. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.01.024 · Cited by 211
3D printing of high drug loaded dosage forms using thermoplastic polyurethanes
Verstraete, G., Samaro, A., Grymonpré, W., Vanhoorne, V., Van Snick, B., Boone, M. N., Hellemans, T., Van Hoorebeke, L., Remon, J. P., & Vervaet, C. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2017.12.002 · Cited by 209
Zhang, J., Yang, W., Vo, A. Q., Feng, X., Ye, X., Kim, D. W., & Repka, M. A. (2017) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2017.08.058 · Cited by 208
3D printing of tablets using inkjet with UV photoinitiation
Clark, E. A., Alexander, M. R., Irvine, D. J., Roberts, C. J., Wallace, M. J., Sharpe, S., Yoo, J., Hague, R. J. M., Tuck, C. J., & Wildman, R. D. (2017) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2017.06.085 · Cited by 207
Genina, N., Boetker, J. P., Colombo, S., Harmankaya, N., Rantanen, J., & Bohr, A. (2017) · Journal of Controlled Release · doi:10.1016/j.jconrel.2017.10.003 · Cited by 204
Gioumouxouzis, C. I., Baklavaridis, A., Katsamenis, O. L., Markopoulou, C. K., Bouropoulos, N., Tzetzis, D., & Fatouros, D. G. (2018) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2018.04.020 · Cited by 201
Influence of Geometry on the Drug Release Profiles of Stereolithographic (SLA) 3D-Printed Tablets
Martinez, P. R., Goyanes, A., Basit, A. W., & Gaisford, S. (2018) · AAPS PharmSciTech · doi:10.1208/s12249-018-1075-3 · Cited by 201
Rheology as a tool for evaluation of melt processability of innovative dosage forms
Aho, J., Boetker, J. P., Baldursdottir, S., & Rantanen, J. (2015) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2015.02.009 · Cited by 191
Pereira, B. C., Isreb, A., Forbes, R. T., Dores, F., Habashy, R., Petit, J.-B., Alhnan, M. A., & Oga, E. F. (2019) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2018.12.009 · Cited by 189
Application of Fused Deposition Modelling (FDM) Method of 3D Printing in Drug Delivery
Long, J., Gholizadeh, H., Lu, J., Bunt, C., & Seyfoddin, A. (2017) · Current Pharmaceutical Design · doi:10.2174/1381612822666161026162707 · Cited by 188
Three-Dimensional Printing in Pharmaceutics: Promises and Problems
Yu, D. G., Zhu, L.-M., Branford-White, C. J., & Yang, X. L. (2008) · Journal of Pharmaceutical Sciences · doi:10.1002/jps.21284 · Cited by 187
Arafat, B., Wojsz, M., Isreb, A., Forbes, R. T., Isreb, M., Ahmed, W., Arafat, T., & Alhnan, M. A. (2018) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2018.03.019 · Cited by 186
Pharmaceutical applications of 3D printing technology: current understanding and future perspectives
Park, B. J., Choi, H. J., Moon, S. J., Kim, S. J., Bajracharya, R., Min, J. Y., & Han, H. (2018) · Journal of Pharmaceutical Investigation · doi:10.1007/s40005-018-00414-y · Cited by 186
Araújo, M. R. P., Sa-Barreto, L. L., Gratieri, T., Gelfuso, G. M., & Cunha-Filho, M. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11030128 · Cited by 184
Yang, Y., Wang, H., Li, H., Ou, Z., & Yang, G. (2018) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2018.01.005 · Cited by 181
Kempin, W., Franz, C., Koster, L.-C., Schneider, F., Bogdahn, M., Weitschies, W., & Seidlitz, A. (2017) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2017.02.014 · Cited by 180
Isreb, A., Baj, K., Wojsz, M., Isreb, M., Peak, M., & Alhnan, M. A. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.04.017 · Cited by 177
Stiffness — an unknown world of mechanical science?
(2000) · Injury · doi:10.1016/s0020-1383(00)80040-6 · Cited by 176
Kim, M. H., Lee, Y. W., Jung, W.-K., Oh, J., & Nam, S. Y. (2019) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2019.06.014 · Cited by 175
Kempin, W., Domsta, V., Grathoff, G., Brecht, I., Semmling, B., Tillmann, S., Weitschies, W., & Seidlitz, A. (2018) · Pharmaceutical Research · doi:10.1007/s11095-018-2405-6 · Cited by 172
Cicala, G., Giordano, D., Tosto, C., Filippone, G., Recca, A., & Blanco, I. (2018) · Materials · doi:10.3390/ma11071191 · Cited by 166
Evolution of PVA gels prepared without crosslinking agents as a cell adhesive surface
Gupta, S., Webster, T. J., & Sinha, A. (2011) · Journal of Materials Science: Materials in Medicine · doi:10.1007/s10856-011-4343-2 · Cited by 163
The Application of 3D Printing in the Formulation of Multilayered Fast Dissolving Oral Films
Ehtezazi, T., Algellay, M., Islam, Y., Roberts, M., Dempster, N. M., & Sarker, S. D. (2018) · Journal of Pharmaceutical Sciences · doi:10.1016/j.xphs.2017.11.019 · Cited by 162
Gupta, S. S., Solanki, N., & Serajuddin, A. T. M. (2016) · AAPS PharmSciTech · doi:10.1208/s12249-015-0426-6 · Cited by 160
Tablets With Material Gradients Fabricated by Three-Dimensional Printing
Yu, D. G., Yang, X. L., Huang, W. D., Liu, J., Wang, Y. G., & Xu, H. (2007) · Journal of Pharmaceutical Sciences · doi:10.1002/jps.20864 · Cited by 159
3D Printing of Pharmaceuticals
Basit, A. W., Gaisford, S., & Publishing, S. I. (2018) · AAPS advances in the pharmaceutical sciences series · doi:10.1007/978-3-319-90755-0 · Cited by 159
Modifying release characteristics from 3D printed drug-eluting products
Boetker, J. P., Water, J. J., Aho, J., Arnfast, L., Bohr, A., & Rantanen, J. (2016) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2016.03.013 · Cited by 158
3D Printing of Pharmaceuticals and Drug Delivery Devices
Mathew, E., Pitzanti, G., Larrañeta, E., & Lamprou, D. A. (2020) · Pharmaceutics · doi:10.3390/pharmaceutics12030266 · Cited by 157
Ilyés, K., Kovács, N. K., Balogh, A., Borbás, E., Farkas, B., Casian, T., Marosi, G., Tomuță, I., & Nagy, Z. K. (2019) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2018.12.019 · Cited by 155
Material Considerations for Fused-Filament Fabrication of Solid Dosage Forms
Fuenmayor, E. A., Forde, M., Healy, A. V., Devine, D. M., Lyons, J. G., McConville, C., & Major, I. (2018) · Pharmaceutics · doi:10.3390/pharmaceutics10020044 · Cited by 148
Öblom, H., Zhang, J., Pimparade, M. B., Speer, I., Preis, M., Repka, M. A., & Sandler, N. (2019) · AAPS PharmSciTech · doi:10.1208/s12249-018-1233-7 · Cited by 146
Fu, J., Yin, H. Y., Yu, X., Xie, C. H., Jiang, H., Jin, Y., & Sheng, F. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.08.011 · Cited by 140
Wu, W., Zheng, Q., Guo, X., Sun, J., & Liu, Y. (2009) · Biomedical Materials · doi:10.1088/1748-6041/4/6/065005 · Cited by 139
Eleftheriadis, G. K., Ritzoulis, C., Bouropoulos, N., Tzetzis, D., Αndreadis, D. A., Boetker, J. P., Rantanen, J., & Fatouros, D. G. (2019) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2019.09.018 · Cited by 138
Kadry, H., Al-Hilal, T. A., Keshavarz, A. A., Alam, F., Xu, C., Joy, A., & Ahsan, F. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.04.010 · Cited by 136
Recent advances in pharmaceutical dosage forms and devices using additive manufacturing technologies
Gioumouxouzis, C. I., Karavasili, C., & Fatouros, D. G. (2019) · Drug Discovery Today · doi:10.1016/j.drudis.2018.11.019 · Cited by 135
Infanger, S., Hämmerli, A., Iliev, S., Baier, A., Stoyanov, E., & Quodbach, J. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.11.048 · Cited by 134
3D Printing Factors Important for the Fabrication of Polyvinylalcohol Filament-Based Tablets
Tagami, T., Fukushige, K., Ogawa, E., Hayashi, N., & Ozeki, T. (2017) · Biological and Pharmaceutical Bulletin · doi:10.1248/bpb.b16-00878 · Cited by 131
Alhijjaj, M., Nasereddin, J., Belton, P., & Qi, S. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11120633 · Cited by 127
Shear Fracture in Cone‐Plate Rheometry
Tanner, R. I., & Keentok, M. (1983) · Journal of Rheology · doi:10.1122/1.549698 · Cited by 118
Wang, C.-C., Tejwani, M. R., Roach, W. J., Kay, J. L., Yoo, J., Surprenant, H. L., Monkhouse, D. C., & Pryor, T. J. (2006) · Drug Development and Industrial Pharmacy · doi:10.1080/03639040500519300 · Cited by 118
Sadia, M., Isreb, A., Abbadi, I., Isreb, M., Aziz, D., Abouselo, A., Timmins, P., & Alhnan, M. A. (2018) · European Journal of Pharmaceutical Sciences · doi:10.1016/j.ejps.2018.07.045 · Cited by 117
Additive Manufacturing of Personalized Pharmaceutical Dosage Forms via Stereolithography
Healy, A. V., Fuenmayor, E. A., Doran, P., Geever, L. M., Higginbotham, C. L., & Lyons, J. G. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11120645 · Cited by 116
Hu, Y., Wang, J., Li, X., Hu, X., Zhou, W., Dong, X., Wang, C., Yang, Z., & Binks, B. P. (2019) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2019.03.024 · Cited by 115
Aita, I. E., Breitkreutz, J., & Quodbach, J. (2018) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2018.11.008 · Cited by 114
Conceição, J., Farto-Vaamonde, X., Goyanes, Á., Adeoye, O., Concheiro, Á., Cabral-Marques, H. M., Lobo, J. M. S., & Alvarez‐Lorenzo, C. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2019.05.084 · Cited by 114
Solvent-dependent properties of electrospun fibrous composites for bone tissue regeneration
Patlolla, A., Collins, G. L., & Arinzeh, T. L. (2009) · Acta Biomaterialia · doi:10.1016/j.actbio.2009.07.028 · Cited by 111
Characterization of microfeatures in selective laser sintered drug delivery devices
Cheah, C. M., Leong, K. F., Chua, C. K., Low, K. H., & Quek, H. S. (2002) · Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine · doi:10.1243/095441102321032166 · Cited by 107
Cold plasma treatment to improve the adhesion of cassava starch films onto PCL and PLA surface
Heidemann, H. M., Dotto, M. E. R., Laurindo, J. B., Carciofi, B. A. M., & da COSTA, C. (2019) · Colloids and Surfaces A Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2019.123739 · Cited by 106
Gautier, E., Perren, S. M., & Cordey, J. (2000) · Injury · doi:10.1016/s0020-1383(00)80027-3 · Cited by 105
Rattanakit, P., Moulton, S. E., Santiago, K. S., Liawruangrath, S., & Wallace, G. G. (2011) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2011.11.007 · Cited by 100
Water-based 3D inkjet printing of an oral pharmaceutical dosage form
Cader, H. K., Rance, G. A., Alexander, M. R., Gonçalves, A. D., Roberts, C. J., Tuck, C. J., & Wildman, R. D. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.04.026 · Cited by 95
Design and 3D printing of multi-compartmental PVA capsules for drug delivery
Matijašić, G., Gretić, M., Vinčić, J., Poropat, A., Cuculić, L., & Rahelić, T. (2019) · Journal of Drug Delivery Science and Technology · doi:10.1016/j.jddst.2019.05.037 · Cited by 93
Haring, A. P., Tong, Y., Halper, J., & Johnson, B. N. (2018) · Advanced Healthcare Materials · doi:10.1002/adhm.201800213 · Cited by 91
Morita, R. (2000) · Journal of Controlled Release · doi:10.1016/s0168-3659(99)00203-5 · Cited by 90
Nukala, P. K., Palekar, S., Patki, M., & Patel, K. R. (2019) · AAPS PharmSciTech · doi:10.1208/s12249-019-1298-y · Cited by 89
Application of Micro-Scale 3D Printing in Pharmaceutics
Kjar, A., & Huang, Y. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11080390 · Cited by 88
Picker‐Freyer, K. M., & Dürig, T. (2007) · AAPS PharmSciTech · doi:10.1208/pt0804092 · Cited by 87
Huanbutta, K., & Sangnim, T. (2019) · Journal of Drug Delivery Science and Technology · doi:10.1016/j.jddst.2019.06.004 · Cited by 87
On the intrinsic sterility of 3D printing
NECHES, R. Y., Flynn, K. J., Zaman, L., Tung, E., & Pudlo, N. A. (2016) · PeerJ · doi:10.7717/peerj.2661 · Cited by 85
Ibrahim, M., Barnes, M., McMillin, R. E., Cook, D. W., Smith, S. E., Halquist, M., Wijesinghe, D. S., & Roper, T. D. (2019) · AAPS PharmSciTech · doi:10.1208/s12249-019-1400-5 · Cited by 81
3D printed, controlled release, tritherapeutic tablet matrix for advanced anti-HIV-1 drug delivery
Siyawamwaya, M., du Toit, L. C., Kumar, P., Choonara, Y. E., Kondiah, P. P. D., & Pillay, V. (2018) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2018.04.007 · Cited by 80
Krkobabić, M., Medarević, D. P., Cvijić, S., Grujić, B., & Ibric, S. R. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.118790 · Cited by 80
3D printing of unique water-soluble polymer-based suppository shell for controlled drug release
Tagami, T., Hayashi, N., Sakai, N., & Ozeki, T. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.118494 · Cited by 77
Chemical structure and glass transition temperature of non-ionic cellulose ethers
Gómez-Carracedo, A., Alvarez‐Lorenzo, C., Gómez-Amoza, J. L., & Concheiro, Á. (2003) · Journal of Thermal Analysis and Calorimetry · doi:10.1023/a:1025434314396 · Cited by 76
Enhancement of interfacial adhesion between starch and grafted poly(ε-caprolactone)
Ortega‐Toro, R., Santagata, G., d’Ayala, G. G., Cerruti, P., Talens, P., Chiralt, A., & Malinconico, M. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.03.070 · Cited by 76
Melocchi, A., Parietti, F., Maccagnan, S., Ortenzi, M. A., Antenucci, S., Vangosa, F. B., Maroni, A., Gazzaniga, A., & Zema, L. (2018) · AAPS PharmSciTech · doi:10.1208/s12249-018-1029-9 · Cited by 71
Fastø, M. M., Genina, N., Kaae, S. S., & Sporrong, S. K. (2019) · International Journal of Clinical Pharmacy · doi:10.1007/s11096-019-00892-6 · Cited by 71
Prasad, E., Islam, M. T., Goodwin, D., Megarry, A. J., Halbert, G., Florence, A. J., & ROBERTSON, J. G. (2019) · Additive manufacturing · doi:10.1016/j.addma.2019.06.027 · Cited by 70
Hyperspectral imaging in quality control of inkjet printed personalised dosage forms
Vakili, H., Kolakovic, R., Genina, N., Marmion, M., Salo, H., Ihalainen, P., Peltonen, J. P. K., & Sandler, N. (2014) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2014.12.034 · Cited by 67
Chen, D., Xu, X., Li, R., Zang, G.-A., Zhang, Y., Wang, M.-R., Xiong, M.-F., Xu, J., Wang, T., Fu, H., et al. (2019) · AAPS PharmSciTech · doi:10.1208/s12249-019-1521-x · Cited by 67
3D printed capsules for quantitative regional absorption studies in the GI tract
Smith, D. M., Kapoor, Y., Hermans, A., Nofsinger, R., Kesisoglou, F., Gustafson, T. P., & Procopio, A. T. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.08.055 · Cited by 66
Singh, A. V., Ansari, M. H. D., Wang, S., Laux, P., Luch, A., Kumar, A., Patil, R., & Nußberger, S. (2019) · Applied Sciences · doi:10.3390/app9040811 · Cited by 66
Tagami, T., Ando, M., Nagata, N., Goto, E., Yoshimura, N., Takeuchi, T., Noda, T., & Ozeki, T. (2018) · Journal of Pharmaceutical Sciences · doi:10.1016/j.xphs.2018.08.026 · Cited by 64
Extrudability analysis of drug loaded pastes for 3D printing of modified release tablets
Zidan, A. S., Alayoubi, A. Y., Coburn, J., Asfari, S., Ghammraoui, B., Cruz, C. N., & Ashraf, M. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.11.025 · Cited by 64
Personalised medicines: More tailored drugs, more tailored delivery
Florence, A. T., & Lee, V. H. L. (2011) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2011.04.047 · Cited by 63
Yang, M., Wang, P., Suwardie, H., & Gogos, C. G. (2010) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2010.10.026 · Cited by 63
Dwivedi, C., Pandey, H., Pandey, A. C., Patil, S., Ramteke, P. W., Laux, P., Luch, A., & Singh, A. V. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11040180 · Cited by 63
New strategies for polymer development in pharmaceutical science — a short review
Godwin, A., Bolina, K., Clochard, M.-C., Dinand, E., Rankin, S., Simic, S., & Brocchini, S. (2001) · Journal of Pharmacy and Pharmacology · doi:10.1211/0022357011776612 · Cited by 60
Saviano, M., Aquino, R. P., Gaudio, P. D., Sansone, F., & Russo, P. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.02.025 · Cited by 57
3D printing in the design of pharmaceutical dosage forms
Souto, E. B., Campos, J. C., Filho, S. C., Teixeira, M. C., Martins‐Gomes, C., Zielińska, A., Carbone, C., & Silva, A. M. (2019) · Pharmaceutical Development and Technology · doi:10.1080/10837450.2019.1630426 · Cited by 56
Zidan, A. S., Alayoubi, A. Y., Asfari, S., Coburn, J., Ghammraoui, B., Aqueel, M. S., Cruz, C. N., & Ashraf, M. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.11.044 · Cited by 53
Messimer, S. L., Patterson, A. E., Muna, N., Deshpande, A. P., & Pereira, T. R. (2018) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp2010012 · Cited by 49
Solanki, N. G., Gumaste, S. G., Shah, A. V., & Serajuddin, A. T. M. (2019) · Journal of Pharmaceutical Sciences · doi:10.1016/j.xphs.2019.05.010 · Cited by 46
Polamaplly, P., Cheng, Y., Shi, X., Manikandan, K., Zhang, X., Kremer, G. E. O., & Qin, H. (2019) · Polymer · doi:10.1016/j.polymer.2019.04.013 · Cited by 45
Ilyés, K., Balogh, A., Casian, T., Igricz, T., Borbás, E., Démuth, B., Vass, P., Menyhárt, L., Kovács, N. K., Marosi, G., et al. (2019) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2019.06.024 · Cited by 44
Pelras, T., Glaß, S., Scherzer, T., Elsner, C., Schulze, A., & Abel, B. (2017) · Polymers · doi:10.3390/polym9120639 · Cited by 43
Dimensional stability of natural fiber-based and hybrid composites
Taib, M. N. A. M., & Julkapli, N. (2019) · Mechanical and Physical Testing of Biocomposites, Fibre-Reinforced Composites and Hybrid Composites · doi:10.1016/b978-0-08-102292-4.00004-7 · Cited by 43
Joo, Y., Shin, I., Ham, G., Abuzar, S. M., Hyun, S.-M., & Hwang, S. (2019) · Journal of Pharmaceutical Investigation · doi:10.1007/s40005-019-00451-1 · Cited by 41
Suwardie, H., Wang, P., Todd, D. B., Panchal, V., Yang, M., & Gogos, C. G. (2011) · European Journal of Pharmaceutics and Biopharmaceutics · doi:10.1016/j.ejpb.2011.03.013 · Cited by 39
Li, P., Zhang, S., Sun, W., Cui, M., Wen, H., Li, Q., Pan, W., & Yang, X. (2019) · AAPS PharmSciTech · doi:10.1208/s12249-019-1455-3 · Cited by 37
Azad, M. A., Osorio, J. G., Brancazio, D., Hammersmith, G., Klee, D., Rapp, K., & Myerson, A. S. (2018) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2018.01.027 · Cited by 36
Self-citationThe Indian Polycap Study (TIPS)
Wald, N., & Law, M. (2009) · The Lancet · doi:10.1016/s0140-6736(09)61584-1 · Cited by 35
Elbadawi, M. (2019) · ACS Omega · doi:10.1021/acsomega.8b03057 · Cited by 34
Renterghem, J. V., Vervaet, C., & Beer, T. D. (2017) · Pharmaceutical Research · doi:10.1007/s11095-017-2239-7 · Cited by 33
Paste Extruder—Hardware Add-On for Desktop 3D Printers
Amza, C. G., Zapciu, A., & Popescu, D. (2017) · Technologies · doi:10.3390/technologies5030050 · Cited by 30
Photocurable Bioinks for the 3D Pharming of Combination Therapies
Acosta‐Vélez, G. F., Linsley, C. S., Zhu, T. Z., Wu, W., & Wu, B. M. (2018) · Polymers · doi:10.3390/polym10121372 · Cited by 29
3D-printability of aqueous poly(ethylene oxide) gels
Viidik, L., Seera, D., Antikainen, O. K., Kogermann, K., Heinämäki, J., & Laidmäe, I. (2019) · European Polymer Journal · doi:10.1016/j.eurpolymj.2019.08.033 · Cited by 29
Maniruzzaman, M. (2019) · Pharmaceutics · doi:10.3390/pharmaceutics11050218 · Cited by 28
Feuerbach, T., Callau-Mendoza, S., & Thommes, M. (2018) · Pharmaceutical Development and Technology · doi:10.1080/10837450.2018.1514522 · Cited by 24
Studies of Hydroxypropyl Methylcellulose Donut-Shaped Tablets
Cheng, K., Zhu, J., Song, X., Sun, L., & Zhang, J. (1999) · Drug Development and Industrial Pharmacy · doi:10.1081/ddc-100102271 · Cited by 20
Aho, J., Renterghem, J. V., Arnfast, L., Beer, T. D., & Rantanen, J. (2017) · International Journal of Pharmaceutics · doi:10.1016/j.ijpharm.2017.06.012 · Cited by 20
On-Demand Manufacturing of Direct Compressible Tablets: Can Formulation Be Simplified?
Azad, M. A., Osorio, J. G., Wang, A., Klee, D. M., Eccles, M. E., Grela, E., Sloan, R., Hammersmith, G., Rapp, K., Brancazio, D., et al. (2019) · Pharmaceutical Research · doi:10.1007/s11095-019-2716-2 · Cited by 18
Self-citationSpence, J. D. (2008) · International Journal of Stroke · doi:10.1111/j.1747-4949.2008.00169.x · Cited by 17
3D printing: the future of manufacturing medicine?
(2015) · Pharmaceutical journal/The pharmaceutical journal · doi:10.1211/pj.2015.20068625 · Cited by 14
Thyroid dysfunction and drug interactions
(2015) · Pharmaceutical journal/The pharmaceutical journal · doi:10.1211/pj.2015.20068601 · Cited by 9
[A review of 3D printing via fused deposition modeling in pharmaceutics].
He, D.-L., Han, F.-G., Wang, Z., & Liu, Q. (2016) · PubMed · Cited by 4
The Indian Polycap Study (TIPS)
Urquhart, J. (2009) · The Lancet · doi:10.1016/s0140-6736(09)61586-5 · Cited by 4
Research works printed but not linked: 3
- Hardung, 2010, Combining HME & solubilization: Soluplus®—The solid solution, Drug Deliv. Technol., 10, 20
- Aho, J., Genina, N., Edinger, M., Botker, J.P., Baldursdottir, S., and Rantanen, J. (June, January 30). Drug-loaded poly (ε-caprolactone) for 3D printing of personalized medicine: A rheological study. Proceedings of the 25th Nordic Rheology Conference, Helsinki, Finland.
- Campbell, 2017, Pharma to table: 3-D printing and the regulatory future of home remedies, Conn. L. Rev. CONNtemplations, 49, 1
Cited by
3D Printing as a Promising Tool in Personalized Medicine
Vaz, V. M., & Kumar, L. (2021) · AAPS PharmSciTech · doi:10.1208/s12249-020-01905-8 · Cited by 409
Seoane-Viaño, I., Januskaite, P., Alvarez-Lorenzo, C., Basit, A. W., & Goyanes, A. (2021) · Journal of Controlled Release · doi:10.1016/j.jconrel.2021.02.027 · Cited by 357
Lignins as Promising Renewable Biopolymers and Bioactive Compounds for High-Performance Materials
Vasile, C., & Baican, M. (2023) · Polymers · doi:10.3390/polym15153177 · Cited by 251
“AM techniques, such as extrusion printing, direct ink writing, and fused deposition modeling, are suitable for printing pure lignin, lignin derivatives, or a combination with other polymers or monomers as fillers or additives necessary to create lignin-based printable feedstocks [278,279].”
MethodPolymeric drug delivery systems by additive manufacturing
Borandeh, S., van Bochove, B., Teotia, A., & Seppälä, J. (2021) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2021.03.022 · Cited by 254
“Like FDM, pressure assisted microsyringe (PAM, also known as semi-solid extrusion, SSE) relies on the computer-controlled preparation of a 3D structure with designed composition and architecture via the deposition of the materials in a layer-bylayer manner [96].”
BackgroundMethodInfluentialRecent advances in 3D printing technologies for wearable (bio)sensors
Kalkal, A., Kumar, S., Kumar, P., Pradhan, R., Willander, M., Packirisamy, G., Kumar, S., & Malhotra, B. D. (2021) · Additive Manufacturing · doi:10.1016/j.addma.2021.102088 · Cited by 232
Metadata
- Authors
- Azad, M. A., Olawuni, D., Kimbell, G., Badruddoza, A. Z. M., Hossain, M. S., & Sultana, T.
- Affiliations
- North Carolina Agricultural and Technical State University (US)
- Virginia Commonwealth University (US)
- City University of New York (US)
- Massachusetts College of Pharmacy and Health Sciences (US)
- Corresponding author
- Azad, Mohammad A.
- Venue
- Pharmaceutics
- Publisher
- MDPI AG
- Published
- 2020-02-03
- Volume
- 12
- Issue
- 2
- Pages
- 124
- ISSN
- 1999-4923 (ISSN-L)
- PMC
- PMC7076526
- OpenAlex
- W3003558240
- Semantic Scholar
- d0e7b174bfd4c9215a0e766bbf1923bb5c15a67d
- Cited by
- 356
- References
- 176
- Citations by year
- 2026: 38 · 2025: 44 · 2024: 48 · 2023: 73 · 2022: 66 · 2021: 57 · 2020: 28
- FWCI
- 3.89
- Type
- journal article
- Language
- en
- Open access
- gold
- dx.doi.org
- Licence
- Locations
- Pharmaceutics (publishedVersion, cc-by)
- Europe PMC (PubMed Central) (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- CUNY Academic Works (City University of New York) (submittedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Topics
- Physical Sciences › Engineering › Industrial and Manufacturing Engineering › Additive Manufacturing and 3D Printing Technologies
- Physical Sciences › Engineering › Building and Construction › Innovations in Concrete and Construction Materials
- Life Sciences › Pharmacology, Toxicology and Pharmaceutics › Pharmaceutical Science › Advanced Drug Delivery Systems
- Keywords
- material extrusion, pharmaceutical 3D printing, fused deposition modeling, polymer rheology, controlled drug release
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.