The DOI matches its Crossref record; 8 of the 9 references it cites were found in a registry or an index.
A one-dimensional model for frost formation on a cold flat surface
Overview
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
Claims other papers make about this one
Each is checked against this paper’s own text: does it say what the citing paper says it does?
In the citing paper
“Fig. 6b suggests that the model describes the measured frost surface temperature reasonably well except for some overprediction in the case of φ = 50% (where the data exhibit somewhat irregular behavior for times below about 40 min).”
From Frost growth and densification in laminar flow over flat surfaces (2011) · cites this paper as [6]
In the citing paper
“Generally reasonable agreement is achieved between the model and the measurements for the frost thickness at the three values of φ = 50, 70 and 80% (Fig. 6a), although it must be admitted that the model somewhat underpredicts the data.”
From Frost growth and densification in laminar flow over flat surfaces (2011) · cites this paper as [6]
In the citing paper
“At φ = 80%, the measured frost surface temperature increases to about -4 ºC, which is relatively close to the melting temperature.”
From Frost growth and densification in laminar flow over flat surfaces (2011) · cites this paper as [6]
In the citing paper
“In the case of φ =50%, the model satisfactorily predicts that data up to t = 90 min, beyond which the data show a small jump in frost thickness.”
From Frost growth and densification in laminar flow over flat surfaces (2011) · cites this paper as [6]
In the citing paper
“The measurements suggest that as the air velocity increases the frost thickness increases, with the data for V = 0.5 m/s and V = 1m/s approach each other for times in excess of about 110 minutes.”
From Frost growth and densification in laminar flow over flat surfaces (2011) · cites this paper as [6]
In the citing paper
“Existing frosting models have focused on predicting the characteristics of heat and mass transfer at the surfaces of basic geometries, such as a flat plate or cylindrical surface [1-12].”
From Performance prediction of a fin-and-tube heat exchanger considering air-flow reduction due to the frost accumulation (2013) · cites this paper as [3]
In the citing paper
“According to their correlations [9,10,11] frost thermal conductivity varies with its density.”
From Frost formation on fin-and-tube heat exchangers. Part I—Modeling of frost formation on fin-and-tube heat exchangers (2004) · cites this paper as [11]
In the citing paper
“Therefore, frost formation on flat plate and cylindrical surface is relatively well known and can be predicted reliably with existing models and correlations.”
From Modeling for predicting frosting behavior of a fin–tube heat exchanger (2006) · cites this paper as [2]
In the citing paper
“relative to experiments, the average relative deviations are 17.01% for these representative literature models”
From A physics-informed quasi-steady frosting model with coupled heat–mass transfer for predicting frost layer growth (2026) · cites this paper as [48]
In the citing paper
“Lee et al. [11] presented a model that only considered the frost layer when calculating the frost formation on a cold flat surface.”
From Numerical Simulation of Frosting on Fin-and-Tube Heat Exchanger Surfaces (2017) · cites this paper as [11]
In the citing paper
“The model assumed that the humid air was saturated at the frost surface, while Webb and coworker [7,12] assumed that the humid air was supersaturated at the frost surface.”
From Numerical Simulation of Frosting on Fin-and-Tube Heat Exchanger Surfaces (2017) · cites this paper as [11]
In the citing paper
“In 1997, this method was used for the validation of the developed one-dimensional model for the frost formation on a cold flat surface by Lee et al. [44].”
From Review on the measurement and calculation of frost characteristics (2018) · cites this paper as [44]
In the citing paper
“the probe of the digital micrometer was made of acrylic resin to prevent frost from melting when it would come in contact with the frost surface.”
From Review on the measurement and calculation of frost characteristics (2018) · cites this paper as [44]
In the citing paper
“the frost thickness was decreased along the air flow direction, but they indicated the difference in frost thickness along air flow direction was negligible when the air velocity was higher than 2 m/s.”
From Frosting mechanism and behaviors on surfaces with simple geometries: A state-of-the-art literature review (2022) · cites this paper as [75]
Citations
Cites
ASHRAE Handbook—1981 Fundamentals
(1981) · Building Services Engineering Research and Technology · doi:10.1177/014362448100200409 · Cited by 3,398
Study of frost properties correlating with frost formation types
Hayashi, Y., Aoki, A., Adachi, S., & Hori, K. (1977) · Journal of Heat Transfer · doi:10.1115/1.3450675 · Cited by 402
A mathematical model for predicting the densification and growth of frost on a flat plate
Tao, Y.-X., Besant, R. W., & Rezkallah, K. S. (1993) · International Journal of Heat and Mass Transfer · doi:10.1016/0017-9310(93)80011-i · Cited by 183
Frost formation with varying environmental parameters
Jones, B. W., & Parker, J. D. (1975) · Journal of Heat Transfer · doi:10.1115/1.3450350 · Cited by 171
(1989) · ASHRAE winter conference papers · Cited by 69
Prediction of Growth Parameters of Frost Deposits in Forced Convection
White, J. E., & Cremers, C. J. (1981) · ASME Journal of Heat and Mass Transfer · doi:10.1115/1.3244426 · Cited by 28
(1994) · Cited by 28
Self-citationNumerical prediction of frost formation on cooled heat exchangers
Sami, S. M., & Duong, T. (1988) · International Communications in Heat and Mass Transfer · doi:10.1016/0735-1933(88)90009-7 · Cited by 9
Research works printed but not linked: 1
- Yamakawa, 1972, Forced convection heat and mass transfer under frost condition, Heat Transfer Japanese Research, 1, 1
Cited by
Sorted by citations
Formation and aging of incipient thin film wax‐oil gels
Singh, P., Venkatesan, R., Fogler, H. S., & Nagarajan, N. (2000) · AIChE Journal · doi:10.1002/aic.690460517 · Cited by 531
The strength of paraffin gels formed under static and flow conditions
Venkatesan, R., Nagarajan, N., Paso, K. G., Yi, Y., Sastry, A. M., & Fogler, H. S. (2005) · Chemical Engineering Science · doi:10.1016/j.ces.2005.02.045 · Cited by 300
“Frost formation (Lee et al., 1997), scale deposition (El-Hattab, 1985), and crystallization fouling of heat exchangers (Bott, 1997) are some examples of solid deposition phenomena that occur in many process systems.”
BackgroundA study of frost growth and densification on flat surfaces
Hermes, C. J. L., Piucco, R. O., Barbosa, J. R., & Melo, C. (2009) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2008.10.006 · Cited by 257
Morphological evolution of thick wax deposits during aging
Singh, P., Venkatesan, R., Fogler, H. S., & Nagarajan, N. (2001) · AIChE Journal · doi:10.1002/aic.690470103 · Cited by 215
New model for frost growth rate
Na, B., & Webb, R. L. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2003.09.001 · Cited by 212
Review on the measurement and calculation of frost characteristics
Song, M., & Dang, C. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.03.094 · Cited by 212
Yao, Y., Jiang, Y., Deng, S., & Ma, Z. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2004.03.013 · Cited by 196
Prediction of the frost formation on a cold flat surface
Lee, K.-S., Jhee, S., & Yang, D.-K. (2003) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(03)00195-9 · Cited by 190
Self-citationXia, Y., Zhong, Y., Hrnjak, P. S., & Jacobi, A. M. (2006) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2006.03.005 · Cited by 152
Seker, D., Karatas, H., & Egrican, N. (2004) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2003.12.003 · Cited by 147
Frost growth and densification in laminar flow over flat surfaces
Kandula, M. (2011) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2011.02.056 · Cited by 141
Mass transfer on and within a frost layer
Na, B., & Webb, R. L. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2003.08.023 · Cited by 129
Shin, J., Tikhonov, A. V., & Kim, C. (2003) · Journal of Heat Transfer · doi:10.1115/1.1518496 · Cited by 123
Electric vehicle range extension strategies based on improved AC system in cold climate – A review
Zhang, Z.-Q., Wang, D.-D., Zhang, C.-Q., & Chen, J.-P. (2018) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2017.12.018 · Cited by 107
Zhang, S., Shang, L., Zhou, L., & Lv, Z. (2022) · Energy & Fuels · doi:10.1021/acs.energyfuels.1c03812 · Cited by 111
Frosting and defrosting characteristics of a fin according to surface contact angle
Kim, K., & Lee, K.-S. (2011) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2011.02.065 · Cited by 108
Self-citationFrosting model for predicting macroscopic and local frost behaviors on a cold plate
Kim, D., Kim, C., & Lee, K.-S. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.11.048 · Cited by 103
Self-citationState-of-the-art review of frost deposition on flat surfaces
Léoni, A., Mondot, M., Durier, F., Revellin, R., & Haberschill, P. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.04.004 · Cited by 103
“On the contrary, Lee et al. (1997) consider frost density as a function of mass flux of densification.”
BackgroundInfluentialAn analytical solution to the problem of frost growth and densification on flat surfaces
Hermes, C. (2012) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2012.06.070 · Cited by 107
Frost formation on a plate with different surface hydrophilicity
Lee, H.-U., Shin, J.-M., Ha, S., Choi, B., & Lee, J.-K. (2004) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2004.05.021 · Cited by 107
Phase change mass transfer model for frost growth and densification
Wu, X., Ma, Q., Chu, F., & Hu, S. (2016) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2016.01.018 · Cited by 100
Sommers, A., Gebhart, C. W., & Hermes, C. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.01.074 · Cited by 68
An experimental study of frost formation on a horizontal cylinder under cross flow
Lee, Y. B., & Ro, S. T. (2001) · International Journal of Refrigeration · doi:10.1016/s0140-7007(00)00073-6 · Cited by 95
Modeling for predicting frosting behavior of a fin–tube heat exchanger
Yang, D.-K., Lee, K.-S., & Song, S. (2006) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2005.09.022 · Cited by 94
Self-citationFrosting model based on phase change driving force
Wu, X.-M., Chu, F., & Ma, Q. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.03.081 · Cited by 94
Transient two-dimensional model of frost formation on a fin-and-tube heat exchanger
Lenic, K., Trp, A., & Frankovic, B. (2009) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2008.06.005 · Cited by 92
Modeling of frost growth and frost properties with airflow over a flat plate
Yun, R., Kim, Y., & Min, M.-K. (2002) · International Journal of Refrigeration · doi:10.1016/s0140-7007(01)00026-3 · Cited by 104
Review Article: A Critical Review of Properties and Models for Frost Formation Analysis
Iragorry, J., Tao, Y.-X., & Jia, S. (2004) · HVAC&R Research · doi:10.1080/10789669.2004.10391111 · Cited by 89
“K8 Obtained N6 Lee et al. (1997)”
MethodInfluentialA generalized simple model for predicting frost growth on cold flat plate
Wang, W., Guo, Q. C., Lu, W. P., Feng, Y. C., & Na, W. (2012) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2011.10.011 · Cited by 89
Kim, J., Choi, H., & Kim, K. (2015) · Applied Energy · doi:10.1016/j.apenergy.2015.02.074 · Cited by 85
“When the outdoor heat exchanger is operated below 0 C, the moisture contained in the outdoor air comes down on the surface of the evaporator fins and frost is generated [2,3].”
Sommers, A. D., Truster, N. L., Napora, A. C., Riechman, A. C., & Caraballo, E. J. (2016) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2016.01.008 · Cited by 84
“In another work [11], the influence of relative humidity was examined, and the frost layer thickness was shown to increase with humidity.”
BackgroundJiang, Y., Fu, H., Yao, Y., Yan, L., & Gao, Q. (2013) · Energy and Buildings · doi:10.1016/j.enbuild.2013.08.055 · Cited by 84
Zhang, L., Song, M., Deng, S., Shen, J., & Dang, C. (2022) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2022.118984 · Cited by 83
Fin spacing optimization of a fin-tube heat exchanger under frosting conditions
Yang, D.-K., Lee, K.-S., & Song, S. (2006) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2006.01.016 · Cited by 81
Self-citationChung, Y., Yoo, J. W., Kim, G. T., & Kim, M. S. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.10.085 · Cited by 81
Eom, Y. H., Chung, Y., Park, M., Hong, S. B., & Kim, M. S. (2021) · Energy · doi:10.1016/j.energy.2021.120542 · Cited by 81
Frost growth and densification on a flat surface in laminar flow with variable humidity
Kandula, M. (2012) · International Communications in Heat and Mass Transfer · doi:10.1016/j.icheatmasstransfer.2012.07.016 · Cited by 79
“[4,5], Cheng and Wu [6], and Hermes et al.”
BackgroundAir-side heat transfer enhancement of a refrigerator evaporator using vortex generation
Sommers, A., & Jacobi, A. (2005) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2005.04.003 · Cited by 89
“[21] correlation for frost thermal conductivity,”
Moallem, E., Cremaschi, L., Fisher, D. E., & Padhmanabhan, S. (2012) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2012.01.022 · Cited by 91
Determination method of defrosting start-time based on temperature measurements
Kim, M.-H., & Lee, K.-S. (2015) · Applied Energy · doi:10.1016/j.apenergy.2015.02.071 · Cited by 79
Self-citationInfluence of Outdoor Air Conditions on the Air Source Heat Pumps Performance
Vocale, P., Morini, G. L., & Spiga, M. (2014) · Energy Procedia · doi:10.1016/j.egypro.2014.01.070 · Cited by 85
Zhao, Y., Wang, R. Z., & Yang, C. (2017) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2016.12.112 · Cited by 78
A mathematical model for frost growth and densification on flat surfaces
ElCheikh, A., & Jacobi, A. M. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.05.054 · Cited by 79
Leoni, A., Mondot, M., Durier, F., Revellin, R., & Haberschill, P. (2017) · Experimental Thermal and Fluid Science · doi:10.1016/j.expthermflusci.2017.06.005 · Cited by 80
Frost formation on a cold surface under turbulent flow
Yang, D.-K., Lee, K.-S., & Cha, D.-J. (2006) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2005.07.003 · Cited by 75
Self-citationBrèque, F., & Nemer, M. (2016) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.06.010 · Cited by 70
Ye, H.-Y., & Lee, K.-S. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.08.026 · Cited by 70
Self-citationModeling of frosting behavior on a cold plate
Yang, D.-K., & Lee, K.-S. (2005) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2004.08.001 · Cited by 77
Self-citationFirst-principles modeling of frost accumulation on fan-supplied tube-fin evaporators
da Silva, D. L., Hermes, C. J. L., & Melo, C. (2011) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2011.04.029 · Cited by 70
A semi-empirical correlation for the frost density
Hermes, C. J. L., Loyola, F. R., & Nascimento, V. S. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2014.02.008 · Cited by 69
The behavior of frost layer growth under conditions favorable for desublimation
Lee, J., & Lee, K.-S. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2017.12.039 · Cited by 68
Self-citationFrost formation from general-low to ultra-low temperatures: A review
Byun, S., Jeong, H., Son, H., Kim, D. R., & Lee, K.-S. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123164 · Cited by 66
Self-citationKim, K., Kim, M.-H., Kim, D. R., & Lee, K.-S. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.12.060 · Cited by 64
Self-citationLocal variation of frost layer thickness and morphology
Qu, K., Komori, S., & Jiang, Y. (2006) · International Journal of Thermal Sciences · doi:10.1016/j.ijthermalsci.2005.05.004 · Cited by 67
Frost layer growth behavior under cryogenic conditions
Lee, J., Jeong, H., Kim, D. R., & Lee, K.-S. (2019) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2019.114333 · Cited by 60
Self-citationYou, Y., Wang, S., Lv, W., Chen, Y., & Gross, U. (2021) · International Journal of Heat and Fluid Flow · doi:10.1016/j.ijheatfluidflow.2021.108807 · Cited by 62
Moallem, E., Padhmanabhan, S., Cremaschi, L., & Fisher, D. E. (2012) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2011.08.010 · Cited by 61
Comments on analogies for correlated heat and mass transfer in turbulent flow
Venkatesan, R., & Fogler, H. S. (2004) · AIChE Journal · doi:10.1002/aic.10146 · Cited by 60
“An example of such a situation is frost formation on the cold surfaces of heat exchangers that are exposed to moist air (Lee et al., 1997).”
BackgroundA semi-empirical correlation for the thermal conductivity of frost
Negrelli, S., & Hermes, C. J. L. (2015) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2015.05.021 · Cited by 59
Moallem, E., Hong, T., Cremaschi, L., & Fisher, D. E. (2013) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2012.09.009 · Cited by 57
Experimental and numerical investigations of frost formation on wavy plates
Ma, Q., Wu, X., Chu, F., & Zhu, B. (2018) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2018.04.098 · Cited by 56
Modeling of frost layer growth considering frost porosity
Lee, J., Kim, J., Kim, D. R., & Lee, K.-S. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.05.098 · Cited by 52
Self-citationFrost spreading on microscale wettability/morphology patterned surfaces
Zhao, Y., & Yang, C. (2017) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2017.04.063 · Cited by 55
Modelling and experimental validation of the hot-gas defrost process of an air-cooled evaporator
Dopazo, J. A., Fernandez-Seara, J., Uhía, F. J., & Diz, R. (2010) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2009.12.027 · Cited by 55
Numerical simulation of frosting behavior and its effect on a direct-contact ambient air vaporizer
Kuang, Y.-W., Yi, C., & Wang, W. (2015) · Journal of Natural Gas Science and Engineering · doi:10.1016/j.jngse.2015.06.042 · Cited by 45
Dynamic heat transfer analysis of liquefied natural gas ambient air vaporizer under frost conditions
Liu, S., Jiao, W., Ren, L., Wang, H., & Zhang, P. (2016) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2016.09.016 · Cited by 50
Transient model of a vertical freezer with door openings and defrost effects
Mastrullo, R., Mauro, A. W., Menna, L., Palma, A., & Vanoli, G. (2014) · Applied Energy · doi:10.1016/j.apenergy.2014.01.069 · Cited by 45
“[13]):”
BackgroundRobust predictive models for estimating frost deposition on horizontal and parallel surfaces
Zendehboudi, A., & Li, X. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2017.05.013 · Cited by 49
A lattice Boltzmann model for solidification of water droplet on cold flat plate
Sun, J., Gong, J., & Li, G. (2015) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2015.07.003 · Cited by 49
Liu, S., Jiao, W., Ren, L., & Tian, X. (2019) · Renewable Energy · doi:10.1016/j.renene.2019.10.072 · Cited by 49
Kim, K.-H., Ko, H.-J., Kim, K., Kim, Y.-W., & Cho, K.-J. (2009) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2008.10.015 · Cited by 47
Experimental investigation of frost retardation for superhydrophobic surface using a luminance meter
Kim, D., Kim, H., Kim, S. W., Kim, D. R., & Lee, K.-S. (2015) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2015.04.042 · Cited by 46
Self-citationEffective thermal conductivity of frost during the crystal growth period
Şahin, A. Z. (2000) · International Journal of Heat and Mass Transfer · doi:10.1016/s0017-9310(99)00162-3 · Cited by 53
(2015) · doi:10.1016/j.expthermflusci.2014.10.006 · Cited by 47
Review on frosting, defrosting and frost management techniques in industrial food freezers
Badri, D., Toublanc, C., Rouaud, O., & Michel Havet, C. (2021) · Renewable and Sustainable Energy Reviews · doi:10.1016/j.rser.2021.111545 · Cited by 45
Numerical Simulation of Frosting on Fin-and-Tube Heat Exchanger Surfaces
Wu, X., Ma, Q., & Chu, F. (2017) · Journal of Thermal Science and Engineering Applications · doi:10.1115/1.4035925 · Cited by 42
Hwang, J., & Cho, K. (2014) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2014.04.026 · Cited by 44
A Semi-Empirical Model for Predicting Frost Properties
Li, S.-M., Yang, K., & Wang, C. (2021) · Processes · doi:10.3390/pr9030412 · Cited by 43
Ma, J., Kim, D., Braun, J. E., & Horton, W. T. (2023) · Energy · doi:10.1016/j.energy.2023.127030 · Cited by 46
Study of the thermal behavior of a latent heat cold storage unit operating under frosting conditions
Simard, A., & Lacroix, M. (2003) · Energy Conversion and Management · doi:10.1016/s0196-8904(02)00183-8 · Cited by 41
Hu, Y., Yuill, D. P., & Ebrahimifakhar, A. (2020) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2020.119423 · Cited by 39
Effects of aluminium surface morphology and chemical modification on wettability
Rahimi, M., Fojan, P., Gurevich, L., & Afshari, A. (2014) · Applied Surface Science · doi:10.1016/j.apsusc.2014.01.059 · Cited by 39
Zhang, L., Song, M., Mao, N., & Dong, J. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.122192 · Cited by 38
Kim, J., Jeon, J., Kim, D. R., & Lee, K.-S. (2018) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.06.023 · Cited by 35
Self-citationChung, Y., Na, S.-I., Yoo, J. W., & Kim, M. S. (2021) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2020.116405 · Cited by 38
Lenic, K., Trp, A., & Frankovic, B. (2009) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2008.12.030 · Cited by 38
Xia, Y., & Jacobi, A. M. (2010) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2009.09.021 · Cited by 35
Negrelli, S., Cardoso, R., & Hermes, C. (2016) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2016.05.135 · Cited by 30
The frost restraining effect of solar air collector applied to air source heat pump
Jiang, Y. Q., Pu, J., Zhang, H., Liu, S., Wang, Y., You, S., Wan, Z., Wu, Z., Fan, X., Liu, Z., et al. (2023) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2023.120215 · Cited by 34
Sommers, A., Napora, A., Truster, N., Caraballo, E., & Hermes, C. (2017) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2016.10.025 · Cited by 32
Nicholas, J. W., Koh, C. A., & Sloan, E. D. (2009) · AIChE Journal · doi:10.1002/aic.11921 · Cited by 32
Lee, S.-H., Lee, M., Yoon, W., & Kim, Y. (2013) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2013.04.018 · Cited by 29
Frost formation and heat transfer on a cold surface in ice fog
Mago, P., & Sherif, S. (2004) · International Journal of Refrigeration · doi:10.1016/j.ijrefrig.2004.10.004 · Cited by 38
Chen, G., Deng, X., Zhang, G., & Yan, X. (2019) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2018.12.133 · Cited by 31
Modeling of the frost deposition by natural convection on horizontal ultra-low-temperature surfaces
Zendehboudi, A., & Hosseini, S. H. (2019) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-019-08087-x · Cited by 26
Mechanisms of trace water vapor frosting on a cryogenic surface in nitrogen gas flow
Qi, Y., Zhi, X., Zhang, H., Wang, K., & Qiu, L. (2021) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2021.120898 · Cited by 31
Wei, W.-Z., Guo, Y.-T., Wang, W., Jiang, Z., Zhang, X., Dai, C.-M., Sun, Y.-Y., Li, B., Wang, S.-Q., & Zhang, C.-X. (2026) · Energy · doi:10.1016/j.energy.2025.139859 · Cited by 34
Three dimensional reconstruction of frost structure by replica method
Takayashiki, M., Nishimura, K., Ściążko, A., Okabe, T., Taniguchi, J., & Shikazono, N. (2022) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2022.123280 · Cited by 30
Sarmiento, A. P., de Sá Sarmiento, F. I. P., Shooshtari, A., & Ohadi, M. (2024) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2024.123680 · Cited by 29
Theoretical study on the critical heat and mass transfer characteristics of a frosting tube
Wang, W., Guo, Q., Feng, Y. C., Lu, W. P., Dong, X., & Zhu, J. H. (2013) · Applied Thermal Engineering · doi:10.1016/j.applthermaleng.2013.01.040 · Cited by 29
“[19], the heat conductive coefficient lf is always a single valued function to the frost density rf.”
Background
Metadata
- Authors
- Lee, K.-S., Kim, W.-S., & Lee, T.-H.
- Affiliations
- Hanyang University (KR)
- Venue
- International Journal of Heat and Mass Transfer
- Publisher
- Elsevier BV
- Published
- 1997-11
- Volume
- 40
- Issue
- 18
- Pages
- 4359-4365
- ISSN
- 0017-9310 (ISSN-L)
- OpenAlex
- W2122043584
- Cited by
- 296
- References
- 9
- Citations by year
- 2026: 17 · 2025: 19 · 2024: 14 · 2023: 18 · 2022: 14 · 2021: 19 · 2020: 9 · 2019: 15 · 2018: 20 · 2017: 24 · 2016: 10 · 2015: 10 · 2014: 16 · 2013: 9 · 2012: 12
- FWCI
- 5.64
- Type
- journal article
- Language
- en
- Open access
- closed
- Locations
- International Journal of Heat and Mass Transfer (publishedVersion)
- Topics
- Physical Sciences › Engineering › Aerospace Engineering › Icing and De-icing Technologies
- Physical Sciences › Engineering › Mechanical Engineering › Refrigeration and Air Conditioning Technologies
- Physical Sciences › Engineering › Mechanical Engineering › Adsorption and Cooling Systems
- Keywords
- frost formation, frost layer, sublimation, heat generation, water vapor concentration, absorption coefficient, one-dimensional model, analytical model
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
