Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells
Open accessThe DOI matches its Crossref record; 175 of the 175 references it cites were found in a registry or an index; 71 of the 306 sources its claims cite were checked for support.
Abstract
The structure of a catalyst layer (CL) significantly impacts the performance, durability, and cost of proton exchange membrane (PEM) fuel cells and is influenced by the catalyst ink and the CL formation process. This review focuses on the effect of the composition, formulation, and preparation of catalyst ink and the CL formation process on the CL structure.
Overview
CoChat Summary
TL;DR
This review synthesizes how the composition, formulation, and preparation of catalyst ink — and the subsequent coating and drying steps — govern the multiscale structure of conventional catalyst layers (CLs) in PEM fuel cells. It concludes that the ink–structure–performance relationship remains incompletely understood and that inconsistent literature conclusions stem from many simultaneously varying manufacturing variables.
Key findings
- The CL is a three-dimensional network of Pt/C, ionomer, and pores with a multiscale structure: 2–5 nm Pt nanoparticles on 10–50 nm carbon black, ionomer films 3.5–20 nm thick, primary catalyst–ionomer agglomerates of a few hundred nm, and secondary agglomerates of a few µm, giving a bimodal pore distribution of 2–20 nm (primary) and >20 nm (secondary) pores; typical CL thickness is 5–10 µm.
- Ink formulation controls ink microstructure and macroscopic properties: catalyst type (e.g., Pt/Ketjen ink is generally more viscous than Pt/Vulcan ink), ionomer type and I/C ratio, and solvent properties (dielectric constant, solubility parameter, viscosity, boiling point, surface tension). Ionomer adsorption follows a Langmuir-type plateau — absorbed ionomer rises from 0.25 to 0.50 I/C then stays nearly constant up to 1.00 I/C, while non-absorbed ionomer increases with I/C; the reported optimum Nafion content is 30 wt.% (I/C ≈ 0.7).
- Ink preparation matters: premixing Pt/C, water, and ethanol before adding ionomer dispersion decreases agglomerate size and yields a more viscous, more homogeneous CL; insufficient dispersion leaves large agglomerates that raise proton, gas, and water transport resistance, while overly aggressive dispersion degrades Pt and ionomer.
- CL formation process controls morphology: solid content requirements differ by technique (spray coating commonly <3 wt.%, e.g., ~0.6, ~1.8, or 2.5 wt.%; roll-to-roll commonly >5 wt.%, e.g., 5.76 wt.% or ~4.5–15 wt.%, up to 33.76 wt.% for screen printing); roll-to-roll can increase fabrication speed by over 500 times versus lab-scale spray coating; cracks arise from fast solvent evaporation, weak ionomer–catalyst interaction, or film defects.
Methods
- Design: narrative review focused on conventional (ink-based) CLs, explicitly excluding structure-ordered CLs; the companion relationship between CL structure and cell performance/durability was covered in the authors' previous review.
- Scope: (1) multiscale CL structure, (2) catalyst ink microstructure and macroscopic properties (rheology, surface tension, stability), (3) effects of catalyst, ionomer, I/C ratio, and solvent, (4) effects of mixing order and dispersion process, (5) CL formation (substrate, coating, drying), and (6) future directions.
- Evidence base: synthesis of prior experimental and modeling literature, including characterization techniques such as DLS, SAS/SANS/SAXS, CV-SANS, ¹⁹F NMR, TEM/Cryo-TEM, SEM/Cryo-SEM, X-CT, and ELS (zeta potential), plus tabulated solvent and commercial ionomer dispersion properties.
Limitations
- Stated by the paper: the relationship between ink formulation/preparation or CL formation and the multiscale CL structure (and ultimately performance and durability) is still unclear and sometimes inconsistent across studies; most ink characterization techniques require modifying the ink (dilution for DLS/ELS, consolidation for TEM/SEM) or only probe local structure; studies on high-solid-content ink, ink storage stability and reversibility of aged ink, and the drying process are limited; inconsistent conclusions arise when variables other than the one under study are not held constant.
- Evident from the text: as a review, it reports no new primary data or meta-analysis; several quantitative values are cited from other works rather than generated here, and some passages (e.g., Table 3 entries and figure captions) are truncated or garbled in the provided text.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures

![Figure 2 Illustration of ionomer-coated catalyst agglomerate [21,45]. Figure 2. Illustration of ionomer-coated catalyst agglomerate [21,45].](https://figures.cochat.ai/paper-figures/db0c1df119f047a2821d28c7fd83fc86/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-2.png)


![Figure 5 Viscosity of Nafion ionomer dispersions ( a ), Pt/HSC dispersions ( b ), Pt/HSC and ionomer dispersions with a fixed 3 wt.% carbon ( c ) in 1-propanol and aqueous solvent mixture (3:1 mass ratio) at different concentrations or I/C ratios (Reprinted with permission from ref. [53]. Copyright (2018) American Chemical Society). Figure 5. Viscosity of Nafion ionomer dispersions ( a ), Pt/HSC dispersions ( b ), Pt/HSC and ionomer dispersions with a fixed 3 wt.% carbon ( c ) in 1-propanol and aqueous solvent mixture (3:1 mass ratio) at different concentrations or I/C ratios (Reprinted with permission from ref. [53]. Copyright (2018) American Chemical Society).](https://figures.cochat.ai/paper-figures/c8224a962e504bf795c9bc2d448bf161/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-5.png)
![Figure 6 Schematics of the distribution of ionomer on carbon and Pt nanoparticles in the conventional case ( left ), the selective distribution of ionomer on only carbon surface through masking Pt nanoparticles ( right ), as well as the oxygen/proton transport in both cases. (Reprinted from Ref. [103] with permission from the Royal Society of Chemistry). Figure 6. Schematics of the distribution of ionomer on carbon and Pt nanoparticles in the conventional case ( left ), the selective distribution of ionomer on only carbon surface through masking Pt nanoparticles ( right ), as well as the oxygen/proton transport in both cases. (Reprinted from Ref. [103] with permission from the Royal Society of Chemistry).](https://figures.cochat.ai/paper-figures/d4d0b60cc2c14103b97670c443ce43fc/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-6.png)
![Figure 7 The chemical structures of 3M PFIA ionomer, Nafion ionomer, 3M PFSA ionomer, and Aquivion ionomer [108,112]. Figure 7. The chemical structures of 3M PFIA ionomer, Nafion ionomer, 3M PFSA ionomer, and Aquivion ionomer [108,112].](https://figures.cochat.ai/paper-figures/59c7b792fcf44f4cb0dc2ecaf3cff4ae/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-7.png)
![Figure 8 ( a ) The physical properties of solvent and their effects on the microstructure and macroscopic properties of catalyst ink, or evaporation rate; ( b ) the size and morphologies of Nafion ionomer in different solvents (Adapted with permission from [128], Copyright (2012) American Chemical Society; Reprinted from [26], Copyright (2013), with permission from Elsevier). Figure 8. ( a ) The physical properties of solvent and their effects on the microstructure and macroscopic properties of catalyst ink, or evaporation rate; ( b ) the size and morphologies of Nafion ionomer in different solvents (Adapted with permission from [128], Copyright (2012) American Chemical Society; Reprinted from [26], Copyright (2013), with permission from Elsevier).](https://figures.cochat.ai/paper-figures/afb87606d70e45d89b9023b9441d0401/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-8.png)
![Figure 9 The structures of Pt/C-Nafion ionomer and CL with insufficient ( a , d ), appropriate ( b , e ), and excessive ( c , f ) dispersion. (( a -c ) Modified with permission from [156], Copyright (2019), American Chemical Society; ( d -e ) Reprinted with permission from [24], Copyright (2019), American Chemical Society; ( f ) Reprinted from [159], Copyright (2014), with permission from Elsevier). Figure 9. The structures of Pt/C-Nafion ionomer and CL with insufficient ( a , d ), appropriate ( b , e ), and excessive ( c , f ) dispersion. (( a -c ) Modified with permission from [156], Copyright (2019), American Chemical Society; ( d -e ) Reprinted with permission from [24], Copyright (2019), American Chemical Society; ( f ) Reprinted from [159], Copyright (2014), with permission from Elsevier).](https://figures.cochat.ai/paper-figures/6afd56e4348a4fb59baff8cb4eef7fd8/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-9.png)

![Figure 11 Stylus profilometry traces of Nafion membrane ( a1 ), CL deposited on membrane (the surface facing the GDL) ( a2 ), GDL (the surface of MPL facing CL) ( b1 ), and CL of GDE (the surface facing the membrane) ( b2 ) (Reprinted from [75] with permission of John Wiley & Sons); ( c , d ) SEM images of cross-section view of the MEA. Cathode: a good CL/membrane interface due to the ionomer overlayer deposited on GDE; Anode: the observed gaps at the interface of MPL and CL which was deposited on the membrane, due to the high MPL surface roughness (root mean square surface roughness: 15.85 µm) (Reprinted with permission from [166]. Copyright (2019) American Chemical Society). The CCM-based MEAs, GDE-based MEAs, and DTM-based MEAs generally have Figure 11. Stylus profilometry traces of Nafion membrane ( a1 ), CL deposited on membrane (the surface facing the GDL) ( a2 ), GDL (the surface of MPL facing CL) ( b1 ), and CL of GDE (the surface facing the membrane) ( b2 ) (Reprinted from [75] with permission of John Wiley & Sons); ( c , d ) SEM images of cross-section view of the MEA. Cathode: a good CL/membrane interface due to the ionomer overlayer deposited on GDE; Anode: the observed gaps at the interface of MPL and CL which was deposited on the membrane, due to the high MPL surface roughness (root mean square surface roughness: 15.85 µ m) (Reprinted with permission from [166]. Copyright (2019) American Chemical Society).](https://figures.cochat.ai/paper-figures/ddc2cb855a164348b938a49c1097adb3/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-11.png)
![Figure 12 ( a ) Schematic of the roll-to-roll manufacturing process coupled with slot-die coating, (Reprinted from [165], Copyright (2020), with permission from Elsevier), ( b ) illustration of slot-die coating (Adapted from [39], Copyright (2019), with permission from Elsevier), ( c ) illustration of gravure coating (Adapted from [38]). Figure 12. ( a ) Schematic of the roll-to-roll manufacturing process coupled with slot-die coating, (Reprinted from [165], Copyright (2020), with permission from Elsevier), ( b ) illustration of slot-die coating (Adapted from [39], Copyright (2019), with permission from Elsevier), ( c ) illustration of gravure coating (Adapted from [38]).](https://figures.cochat.ai/paper-figures/2ec7807590cc4eebbdf1aef0c98880fa/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-12.png)
![Figure 13 Weight change of the ink film at different drying conditions (20 or 40 °C, dry-0% R humid-80% RH) and the schematics of the structure change from the ink film to the dried CL (R printed from [56], Copyright (2016), with permission from Elsevier). Figure 13. Weight change of the ink film at different drying conditions (20 or 40 ◦ C, dry-0% RH, humid-80% RH) and the schematics of the structure change from the ink film to the dried CL (Reprinted from [56], Copyright (2016), with permission from Elsevier).](https://figures.cochat.ai/paper-figures/0f08e3663fbf4033af01d3475c5a0809/effect-of-catalyst-ink-and-formation-process-on-the-multiscale-structure-of-figure-13.png)
Verification
Claims the paper makes
61 Valid · 20 Not valid · 137 Not checked · 126 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“The equilibrium constant of ionomer adsorption on catalyst decreases with increasing the amount of the surface oxygen-containing groups [96].”
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > 4.1. Catalyst and Catalyst Content in the Ink
What the sources say
- Disputedcites [96] Andersen, 2014, Adsorption Behavior of Perfluorinated Sulfonic Acid Ionomer on Highly Graphitized Carbon Nanofibers and Their Thermal Stabilities, J. Phys. Chem. C sourceExperimental — accuracy not yet measured
The Discussion (p. 8) reports that the equilibrium constant first falls as oxygen-containing groups increase, but rises to about 21 for the more highly oxidized CNFF3 sample. The Conclusions (p. 10) likewise describe an initial decrease followed by an increase, contrary to the claimed continuous decrease. (LLM, conf=0.90)
Checked by a reasoning model — may be wrong.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“The penetration degree depends on the deposition method due to the difference in the viscosity of the used ink or the drying rates for various coating techniques [38].”
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > •
What the sources say
- Disputedcites [38] Mauger, 2018, Gravure coating for roll-to-roll manufacturing of proton-exchange-membrane fuel cell catalyst layers, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
The Results and Discussion section reports no significant catalyst penetration into the microporous layer with either gravure or spray coating. Although the paper describes differences in ink concentration, viscosity, and drying between the methods, it says the observed penetration difference relative to another study is likely due to the substrate’s microporous layer, not the coating method. (LLM, conf=0.90)
Checked by a reasoning model — may be wrong.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“al. found that the decrease in the primary and secondary agglomerates size resulting from dilution approaches 20%, through studying the ink with and without dilution by using a recent DLS apparatus [34].”
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > 3.1. Microstructure of Catalyst Ink
What the sources say
- Partly supportedcites [34] Shukla, 2017, Experimental and theoretical analysis of ink dispersion stability for polymer electrolyte fuel cell applications, J. Electrochem. Soc. sourceExperimental — accuracy not yet measured
The ink-dilution discussion and Table V report that average carbon-ink particle diameter fell from 284.5 to 233.1 nm—less than 20%—as the ink was diluted. The Sample preparation section confirms that DLS was used to compare diluted and undiluted ink. The paper does not report separate size decreases for primary and secondary agglomerates. Exact page numbers are unavailable in our copy. (LLM, conf=0.87)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“During the solvent evaporation process, the movement, aggregation, or self-assembly of the agglomerates in the ink film occur, determining the final structure of the CL [40,41].”
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > 1. Introduction
What the sources say
- Partly supportedcites [40] Zhao, 2019, The effect of ink dilution and evaporation on the microstructures of catalyst layers in polymer electrolyte membrane fuel cells, Int. J. Energy Res. sourceExperimental — accuracy not yet measured
The Introduction (page unavailable) says solvent evaporation determines initial catalyst-layer microstructures and affects catalyst-particle movement. Section 3.2 (page unavailable) describes particles moving and accumulating as droplets dry, but does not establish self-assembly or aggregation of agglomerates in an ink film. (LLM, conf=0.84)
- Partly supportedcites [41] Mauger, 2021, Development of high-performance roll-to-roll-coated gas-diffusion-electrode-based fuel cells, J. Power Sources sourceExperimental — accuracy not yet measured
The Introduction (pp. 4–5) explains that evaporation and diffusion affect particle distribution as an ink film dries, and the Results and Discussion (p. 14) report likely ionomer migration during drying. This supports movement shaping the final catalyst-layer structure, but the cited passages do not establish that agglomerates aggregate or self-assemble during evaporation. (LLM, conf=0.84)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“Therefore, the secondary catalyst-ionomer agglomerates usually exhibit a bimodal pore size distribution, including 2-20 nm-sized pores within primary agglomerates and larger over 20 nm-sized pores between primary agglomerates in the secondary agglomerates-the former is often referred to as the primary pores, and the latter the secondary pores [47,48].”
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > 2. Multiscale Structure of CL in PEM Fuel Cell
What the sources say
- Not checked — no full text of the sourcecites [47] Ohma, 2011, Analysis of proton exchange membrane fuel cell catalyst layers for reduction of platinum loading at Nissan, Electrochim. Acta source
- Supportedcites [48] Soboleva, 2010, On the Micro-, Meso-, and Macroporous Structures of Polymer Electrolyte Membrane Fuel Cell Catalyst Layers, ACS Appl. Mater. Interfaces source
The Carbon Powders section describes 2–20 nm pores within carbon-particle agglomerates and pores larger than 20 nm between agglomerates. The introductory section describes this as a bimodal pore-size distribution and calls the two groups primary and secondary pores. (LLM, conf=0.91)
plain- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
174 more claims · 32 with their cited sources checked
Create a free account to see all 344 claims and to verify the 4 references still open.
- Probably not a substantial claim. 57
- It may state two separate claims as one. 128
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > 8. Concluding Remarks
“| Formamide | HCONH 2 | 111 | 3.34 | 210 | 57.03 | 16.6 | 17.2 | 26.2 | 19.0 |”
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > 4.3. Solvent
“δ = δ total = δ D 2 + δ P 2 + δ H 2 (3”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
“1 MPa 1/2 is equal to 2.0455 (cal/cm 3 ) 1/2 [129].”
§ Effect of Catalyst Ink and Formation Process on the Multiscale Structure of Catalyst Layers in PEM Fuel Cells > 4.3. Solvent
Reported 2.0455 · recomputed 0.488878
Citations
Cites
Electrocatalyst approaches and challenges for automotive fuel cells
Debe, M. K. (2012) · Nature · doi:10.1038/nature11115 · Cited by 5,885 · cited 1×
“, internal combustion engines or other kinds of fuel cells, PEM fuel cells also have the advantages of high energy efficiency and low operation temperature [3,4].”
BackgroundHansen Solubility Parameters: A User's Handbook, Second Edition
Hansen, C. M. (2007) · CRC Press eBooks · doi:10.1201/9781420006834 · Cited by 3,156
New Insights into Perfluorinated Sulfonic-Acid Ionomers
Kusoglu, A., & Weber, A. Z. (2017) · Chemical Reviews · doi:10.1021/acs.chemrev.6b00159 · Cited by 2,432
Biaxially strained PtPb/Pt core/shell nanoplate boosts oxygen reduction catalysis
Bu, L., Zhang, N., Guo, S., Zhang, X., Li, J., Yao, J., Wu, T., Lu, G., Ma, J.-Y., Su, D., et al. (2016) · Science · doi:10.1126/science.aah6133 · Cited by 1,642
Ultrafine jagged platinum nanowires enable ultrahigh mass activity for the oxygen reduction reaction
Li, M., Zhao, Z., Cheng, T., Fortunelli, A., Chen, C.-Y., Yu, R., Zhang, Q., Gu, L., Merinov, B. V., Lin, Z., et al. (2016) · Science · doi:10.1126/science.aaf9050 · Cited by 1,605
Engineering bunched Pt-Ni alloy nanocages for efficient oxygen reduction in practical fuel cells
Tian, X., Zhao, X., Su, Y.-Q., Wang, L., Wang, H., Dang, D., Chi, B., Liu, H., Hensen, E. J. M., Lou, X. W. (., et al. (2019) · Science · doi:10.1126/science.aaw7493 · Cited by 1,527
Self-citationKonsistenzmessungen von Gummi-Benzollösungen
Herschel, W. H., & Bulkley, R. (1926) · Kolloid-Zeitschrift · doi:10.1007/bf01432034 · Cited by 1,499
New roads and challenges for fuel cells in heavy-duty transportation
Cullen, D. A., Neyerlin, K. C., Ahluwalia, R. K., Mukundan, R., More, K. L., Borup, R. L., Weber, A. Z., Myers, D. J., & Kusoglu, A. (2021) · Nature Energy · doi:10.1038/s41560-021-00775-z · Cited by 1,277
Wang, Y.-J., Zhao, N., Fang, B., Li, H., Bi, X. T., & Wang, H. (2015) · Chemical Reviews · doi:10.1021/cr500519c · Cited by 1,267 · cited 1×
“platinum (Pt)-based catalysts is necessary to promote the electrode reactions to supply the required performance and durability for practical application [5].”
BackgroundBoosting Fuel Cell Performance with Accessible Carbon Mesopores
Yarlagadda, V., Carpenter, M. K., Moylan, T. E., Kukreja, R. S., Koestner, R., Gu, W., Thompson, L., & Kongkanand, A. (2018) · ACS Energy Letters · doi:10.1021/acsenergylett.8b00186 · Cited by 686
Banham, D., & Ye, S. (2017) · ACS Energy Letters · doi:10.1021/acsenergylett.6b00644 · Cited by 583 · cited 1×
“, internal combustion engines or other kinds of fuel cells, PEM fuel cells also have the advantages of high energy efficiency and low operation temperature [3,4].”
BackgroundImaging the Microscopic Structure of Shear Thinning and Thickening Colloidal Suspensions
Cheng, X., McCoy, J. H., Israelachvili, J. N., & Cohen, I. (2011) · Science · doi:10.1126/science.1207032 · Cited by 524 · cited 1×
“, viscosity, different from the stationary case, which is commonly due to the change of the fluid microstructure caused by shear force [70].”
BackgroundFuel Cell Catalyst Layers: A Polymer Science Perspective
Holdcroft, S. (2014) · Chemistry of Materials · doi:10.1021/cm401445h · Cited by 481 · cited 3×
“Although typical CLs only have a thickness of 5–10 μm [21], they have a complicated multiscale structure, i.”
BackgroundHigh-concentration zeta potential measurements using light-scattering techniques
Kaszuba, M., Corbett, J., Watson, F. M., & Jones, A. (2010) · Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences · doi:10.1098/rsta.2010.0175 · Cited by 430 · cited 3×
“The zeta potential of particles in the colloidal system is the electric potential at the outside of the stationary layer on the particle surface, i.e., the electric potential at the shear plane of the particle, which could be measured by Electrophoretic Light Scattering (ELS) [63].”
BackgroundInfluentialVelazquez Abad, A., & Dodds, P. E. (2020) · Energy Policy · doi:10.1016/j.enpol.2020.111300 · Cited by 425 · cited 1×
“If green hydrogen, commonly produced from renewable energy through water electrolysis, could be used as fuel, the by-products include only water and heat, significantly reducing zero-carbon emissions [1,2].”
BackgroundSoboleva, T., Zhao, X., Malek, K., Xie, Z., Navessin, T., & Holdcroft, S. (2010) · ACS Applied Materials & Interfaces · doi:10.1021/am900600y · Cited by 424 · cited 2×
“primary agglomerates in the secondary agglomerates—the former is often referred to as the primary pores, and the latter the secondary pores [47,48].”
BackgroundThree-dimensional analysis of Nafion layers in fuel cell electrodes
Lopez-Haro, M., Guétaz, L., Printemps, T., Morin, A., Escribano, S., Jouneau, P.-H., Bayle-Guillemaud, P., Chandezon, F., & Gebel, G. (2014) · Nature Communications · doi:10.1038/ncomms6229 · Cited by 402 · cited 3×
“ered with a thin ionomer film, (iii) partially covered by ionomer, and (iv) completely uncovered by ionomer [45].”
BackgroundPark, Y.-C., Tokiwa, H., Kakinuma, K., Watanabe, M., & Uchida, M. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.02.091 · Cited by 389
The Key to High Performance Low Pt Loaded Electrodes
Orfanidi, A., Madkikar, P., El-Sayed, H. A., Harzer, G. S., Kratky, T., & Gasteiger, H. A. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.1621704jes · Cited by 276
Kim, O.-H., Cho, Y.-H., Kang, S. H., Park, H.-Y., Kim, M., Lim, J. W., Chung, D. Y., Lee, M. J., Choe, H., & Sung, Y.-E. (2013) · Nature Communications · doi:10.1038/ncomms3473 · Cited by 275
Kodama, K., Motobayashi, K., Shinohara, A., Hasegawa, N., Kudo, K., Jinnouchi, R., Osawa, M., & Morimoto, Y. (2018) · ACS Catalysis · doi:10.1021/acscatal.7b03571 · Cited by 258 · cited 1×
“The ionomer exhibits a preferential interaction with Pt relative to carbon through the side chain [50,89].”
BackgroundMorphological features (defects) in fuel cell membrane electrode assemblies
Kundu, S., Fowler, M. W., Simon, L. C., & Grot, S. (2006) · Journal of Power Sources · doi:10.1016/j.jpowsour.2005.12.027 · Cited by 244
Green hydrogen as feedstock: Financial analysis of a photovoltaic-powered electrolysis plant
Nicita, A., Maggio, G., Andaloro, A. P. F., & Squadrito, G. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.02.062 · Cited by 242 · cited 1×
“If green hydrogen, commonly produced from renewable energy through water electrolysis, could be used as fuel, the by-products include only water and heat, significantly reducing zero-carbon emissions [1,2].”
BackgroundNgo, T. T., Yu, T. L., & Lin, H.-L. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.10.055 · Cited by 231 · cited 6×
“(a) The physical properties of solvent and their effects on the microstructure and macroscopic properties of catalyst ink, or evaporation rate; (b) the size and morphologies of Nafion ionomer in different solvents (Adapted with permission from [128], Copyright (2012) American Chemical Society; Reprinted from [26], Cop…”
BackgroundMethodInfluentialSolubility Parameters: Theory and Application
Burke, J. J. (1984) · Cited by 218
Nafion in dilute solvent systems: Dispersion or solution?
Welch, C., Labouriau, A., Hjelm, R., Orler, B., Johnston, C., & Kim, Y. S. (2012) · ACS Macro Letters · doi:10.1021/mz3005204 · Cited by 211
Tian, Z. Q., Lim, S. H., Poh, C. K., Tang, Z., Xia, Z., Luo, Z., Shen, P. K., Chua, D., Feng, Y. P., Shen, Z., et al. (2011) · Advanced Energy Materials · doi:10.1002/aenm.201100371 · Cited by 210 · cited 1×
“125 mg/cm2 MEA (membrane electrode assembly, MEA) without sacrificing fuel cell performance in some structure-ordered CLs [16,18,19].”
BackgroundOhma, A., Mashio, T., Sato, K., Iden, H., Ono, Y., Sakai, K., Akizuki, K., Takaichi, S., & Shinohara, K. (2011) · Electrochimica Acta · doi:10.1016/j.electacta.2011.04.058 · Cited by 209
Shin, S.-J., Lee, J.-K., Ha, H.-Y., Hong, S.-A., Chun, H.-S., & Oh, I.-H. (2002) · Journal of Power Sources · doi:10.1016/s0378-7753(01)01045-x · Cited by 205
Wang, M., Park, J. H., Kabir, S., Neyerlin, K. C., Kariuki, N. N., Lv, H., Stamenkovic, V. R., Myers, D. J., Ulsh, M., & Mauger, S. A. (2019) · ACS Applied Energy Materials · doi:10.1021/acsaem.9b01037 · Cited by 192
Effect of ball size and powder loading on the milling efficiency of a laboratory-scale wet ball mill
Shin, H., Lee, S., Suk Jung, H., & Kim, J.-B. (2013) · Ceramics International · doi:10.1016/j.ceramint.2013.04.093 · Cited by 190 · cited 1×
“The structure-ordered CLs are usually ultrathin, less than 1 μm or even less than 200 nm in some cases [14,16,20], which will result in inherently low mass transport resistance versus the conventional CLs with a thickness of several μm due to the shorter transport distance.”
BackgroundOptimum Nafion content in PEM fuel cell electrodes
Sasikumar, G., Ihm, J. W., & Ryu, H. (2004) · Electrochimica Acta · doi:10.1016/j.electacta.2004.01.126 · Cited by 187 · cited 1×
“2), Pt loading in the electrode [94], or operation conditions (e.”
BackgroundDebe, M. K. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.049306jes · Cited by 183 · cited 3×
“However, most structureordered CLs are susceptible to topple over [14,18], thus losing their ordered structure during the decal or hot-pressing process.”
BackgroundThe Controllable Design of Catalyst Inks to Enhance PEMFC Performance: A Review
Guo, Y., Pan, F., Chen, W., Ding, Z., Yang, D., Li, B., Ming, P., & Zhang, C. (2021) · Electrochemical Energy Reviews · doi:10.1007/s41918-020-00083-2 · Cited by 175
Ink solvent dependence of the ionomer distribution in the catalyst layer of a PEMFC
Orfanidi, A., Rheinländer, P. J., Schulte, N., & Gasteiger, H. A. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.1251814jes · Cited by 169
Ferrara, A., Jakubek, S., & Hametner, C. (2021) · Energy Conversion and Management · doi:10.1016/j.enconman.2020.113795 · Cited by 161
Murata, S., Imanishi, M., Hasegawa, S., & Namba, R. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.11.073 · Cited by 155 · cited 1×
“, vertically aligned carbon nanotubes [10,11] or conductive polymer [12,13]), ordered catalysts [14–16], ordered ionomer materials [17], or ordered non-conductive materials (e.”
BackgroundRheological Investigation on the Microstructure of Fuel Cell Catalyst Inks
Khandavalli, S., Park, J. H., Kariuki, N. N., Myers, D. J., Stickel, J. J., Hurst, K., Neyerlin, K. C., Ulsh, M., & Mauger, S. A. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b15039 · Cited by 153 · cited 9×
“To the best of our knowledge, most catalyst inks usually give a shear-thinning behavior [28,52,53,74]; only a few cases exhibit a nearly Newtonian behavior for shear rate of about 1~1000 s−1 [53,75].”
BackgroundInfluentialMicrostructure of Catalyst Layers in PEM Fuel Cells Redefined: A Computational Approach
Malek, K., Mashio, T., & Eikerling, M. (2011) · Electrocatalysis · doi:10.1007/s12678-011-0047-0 · Cited by 151
Van Cleve, T., Khandavalli, S., Chowdhury, A., Medina, S., Pylypenko, S., Wang, M., More, K. L., Kariuki, N., Myers, D. J., Weber, A. Z., et al. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b17614 · Cited by 148 · cited 3×
“These would affect the local gas transport resistance through the ionomer layer or the interfacial resistance between the ionomer film and Pt [60].”
BackgroundTakahashi, S., Mashio, T., Horibe, N., Akizuki, K., & Ohma, A. (2015) · ChemElectroChem · doi:10.1002/celc.201500131 · Cited by 143 · cited 4×
“, water/alcohol mixed solvent, due to hydrophobic interaction [25]; in contrast, increasing the hydrophilicity of carbon through introducing plenty of functional groups tends to form small agglomerates in polar solvents due to an enhanced repulsion force [51].”
BackgroundMethodInfluentialSassin, M. B., Garsany, Y., Gould, B. D., & Swider-Lyons, K. E. (2017) · Analytical Chemistry · doi:10.1021/acs.analchem.6b03005 · Cited by 143
Millington, B., Whipple, V., & Pollet, B. G. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.06.024 · Cited by 141 · cited 2×
“For example, different coating techniques have different demands on the viscosity or the choice of solvent [37,38].”
BackgroundImpact of manufacturing processes on proton exchange membrane fuel cell performance
Shahgaldi, S., Alaefour, I., & Li, X. (2018) · Applied Energy · doi:10.1016/j.apenergy.2018.05.086 · Cited by 138
Self-citationShukla, S., Bhattacharjee, S., Weber, A. Z., & Secanell, M. (2017) · Journal of The Electrochemical Society · doi:10.1149/2.0961706jes · Cited by 137 · cited 4×
“As the catalyst agglomerates are commonly covered by ionomer in the catalyst ink, solvent affects the dispersion or dispersion stability of catalyst likely through impacting the ionomer coverage on catalyst or the conformation of the adsorbed ionomer [34].”
BackgroundMethodInfluentialControlling cracking formation in fuel cell catalyst layers
Kumano, N., Kudo, K., Suda, A., Akimoto, Y., Ishii, M., & Nakamura, H. (2019) · Journal of Power Sources · doi:10.1016/j.jpowsour.2019.02.058 · Cited by 135
Yakovlev, Y. V., Lobko, Y. V., Vorokhta, M., Nováková, J., Mazur, M., Matolínová, I., & Matolín, V. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229531 · Cited by 135
Improved PEM fuel cell electrodes by controlled self-assembly
Middelman, E. (2002) · Fuel Cells Bulletin · doi:10.1016/s1464-2859(02)11028-5 · Cited by 132 · cited 1×
“[9], which is constituted of the aligned electronic conductor loaded with Pt nanoparticles perpendicular to the membrane, being covered by ~10 nm thick ionomer layer.”
Kim, T.-H., Yi, J.-Y., Jung, C.-Y., Jeong, E., & Yi, S.-C. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2016.12.015 · Cited by 127
Catalyst layer ink interactions that affect coatability
Dixit, M. B., Harkey, B. A., Shen, F., & Hatzell, K. B. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0191805jes · Cited by 126 · cited 1×
“However, the addition of catalyst and ionomer will change the surface tension [33].”
BackgroundDoo, G., Lee, J. H., Yuk, S., Choi, S., Lee, D.-H., Lee, D. W., Kim, H. G., Kwon, S. H., Lee, S. G., & Kim, H.-T. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b01751 · Cited by 126 · cited 4×
“It was believed that the colloid ionomer with fine dispersion or specific size adsorbs on catalyst agglomerates, resulting in the formation of the slightly larger agglomerates, which improves the CL microstructure and enhances the porosity and then the gas transport, further the fuel cell performance [23,25,132,138,13…”
BackgroundMethodInfluentialYang, F., Xin, L., Uzunoglu, A., Qiu, Y., Stanciu, L., Ilavsky, J., Li, W., & Xie, J. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b12949 · Cited by 124 · cited 3×
“If introducing -SO3H onto the carbon surface, a similar phenomenon will be incurred [51].”
BackgroundPark, Y.-C., Kakinuma, K., Uchida, H., Watanabe, M., & Uchida, M. (2015) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.10.149 · Cited by 123
Uchida, M., Park, Y.-C., Kakinuma, K., Yano, H., Tryk, D. A., Kamino, T., Uchida, H., & Watanabe, M. (2013) · Physical Chemistry Chemical Physics · doi:10.1039/c3cp51801a · Cited by 122 · cited 1×
“However, for Pt/Ketjen, Ketjen carbon black is a porous carbon support and has a high surface area and abundant internal pore; only∼50% or even less than 50% of Pt nanoparticles reside on the external surface [87,88].”
BackgroundInherent Acidity of Perfluorosulfonic Acid Ionomer Dispersions and Implications for Ink Aggregation
Berlinger, S. A., McCloskey, B. D., & Weber, A. Z. (2018) · The Journal of Physical Chemistry B · doi:10.1021/acs.jpcb.8b06493 · Cited by 122 · cited 4×
“Due to the high affinity with water molecules, the side chains of Nafion tend to be extended out in the waterrich solvent mixtures, which would increase the coulomb repulsion force between Nafion agglomerates, or between catalyst–Nafion agglomerates, or between both, enhancing the colloidal stability of the ink, where…”
BackgroundInfluentialYuan, X., Nayoze-Coynel, C., Shaigan, N., Fisher, D. C., Zhao, N., Zamel, N., Gazdzicki, P., Ulsh, M., Friedrich, K. A., Girard, F., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229540 · Cited by 118
Self-citationThe importance of ultrasonic parameters in the preparation of fuel cell catalyst inks
Pollet, B. G., & Goh, J. T. E. (2014) · Electrochimica Acta · doi:10.1016/j.electacta.2013.09.160 · Cited by 117
Dual cohesive energy densities of perfluorosulphonic acid (Nafion) membrane
Yeo, R. S. (1980) · Polymer · doi:10.1016/0032-3861(80)90015-4 · Cited by 117
Wang, W., Chen, S., Li, J., & Wang, W. (2015) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2015.02.027 · Cited by 115 · cited 5×
“, the solvent with low boiling point, easily causes much difference in the drying speed between the surface and interior, resulting in the increased drying stress and then cracking in the dried CL [42,66].”
BackgroundInfluentialRoll-to-roll production of catalyst coated membranes for low-temperature electrolyzers
Park, J., Kang, Z., Bender, G., Ulsh, M., & Mauger, S. A. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228819 · Cited by 115
Jeon, S., Lee, J., Rios, G. M., Kim, H.-J., Lee, S.-Y., Cho, E., Lim, T.-H., & Hyun Jang, J. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.06.044 · Cited by 113
White, R. T., Wu, A., Najm, M., Orfino, F. P., Dutta, M., & Kjeang, E. (2017) · Journal of Power Sources · doi:10.1016/j.jpowsour.2017.03.058 · Cited by 109
Effect of Pt and Ionomer Distribution on Polymer Electrolyte Fuel Cell Performance and Durability
Kobayashi, A., Fujii, T., Harada, C., Yasumoto, E., Takeda, K., Kakinuma, K., & Uchida, M. (2021) · ACS Applied Energy Materials · doi:10.1021/acsaem.0c02841 · Cited by 109 · cited 2×
“, nanopore volume [88]) or Pt loading on carbon [92,93] will impact the optimal I/C ratio; certainly, the optimal I/C ratio also depends on the type of ionomer (discussed more in Section 4.”
BackgroundOsuji, C. O., Kim, C., & Weitz, D. A. (2008) · Physical Review E · doi:10.1103/physreve.77.060402 · Cited by 106 · cited 1×
“Badly dispersed carbon inks with dry agglomerates could exhibit shear thickening behavior at critical shear rates, whereas the overall flow behavior is shear thinning [76,77].”
BackgroundSchmies, H., Hornberger, E., Anke, B., Jurzinsky, T., Nong, H. N., Dionigi, F., Kühl, S., Drnec, J., Lerch, M., Cremers, C., et al. (2018) · Chemistry of Materials · doi:10.1021/acs.chemmater.8b03612 · Cited by 105
Fouzaï, I., Gentil, S., Bassetto, V. C., Silva, W. O., Maher, R., & Girault, H. H. (2021) · Journal of Materials Chemistry A · doi:10.1039/d0ta07470e · Cited by 102
Negi, A. S., & Osuji, C. O. (2009) · Rheologica Acta · doi:10.1007/s00397-008-0341-9 · Cited by 99
Nano-scale control of the ionomer distribution by molecular masking of the Pt surface in PEMFCs
Doo, G., Yuk, S., Lee, J. H., Choi, S., Lee, D.-H., Lee, D. W., Hyun, J., Kwon, S. H., Lee, S. G., & Kim, H.-T. (2020) · Journal of Materials Chemistry A · doi:10.1039/c9ta14002f · Cited by 99
Understanding inks for porous-electrode formation
Hatzell, K. B., Dixit, M. B., Berlinger, S. A., & Weber, A. Z. (2017) · J. Mater. Chem. A · doi:10.1039/c7ta07255d · Cited by 97 · cited 4×
“For the time being, there have been some reviews focused on the optimization of the formulation and dispersion techniques of catalyst ink, the characterization and modeling of catalyst ink, the coating techniques, or the underlying interactions between solvent, ionomer, and catalyst [29,35,43].”
BackgroundMethodInfluentialBalu, R., Choudhury, N. R., Mata, J. P., de Campo, L., Rehm, C., Hill, A. J., & Dutta, N. K. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b20645 · Cited by 96
Impact of Catalyst Ink Dispersing Solvent on PEM Fuel Cell Performance and Durability
Lei, C., Yang, F., Macauley, N., Spinetta, M., Purdy, G., Jankovic, J., Cullen, D. A., More, K. L., Kim, Y. S., & Xu, H. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abf2b0 · Cited by 93 · cited 4×
“It was reported that cracks [57,58,141] or larger ionomer patches [49] are more likely formed in the CLs made of the ink containing water/2-propanol.”
BackgroundInfluentialEffect of dispersion solvent in catalyst ink on proton exchange membrane fuel cell performance
Huang, D.-C., Yu, P.-J., Liu, F.-J., Huang, S.-L., Hsueh, K.-L., Chen, Y.-C., Wu, C.-H., Chang, W.-C., & Tsau, F.-H. (2011) · International Journal of Electrochemical Science · doi:10.1016/s1452-3981(23)18202-2 · Cited by 93 · cited 5×
“(2) Viscosity: The solvent viscosity has an effect on the ink viscosity and stability, coating process, and drying process [42,126].”
BackgroundInfluentialNgo, T. T., Yu, T. L., & Lin, H.-L. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2013.03.055 · Cited by 92
Shahgaldi, S., Alaefour, I., Unsworth, G., & Li, X. (2017) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2017.02.127 · Cited by 89
Self-citationDu, S., Li, W., Wu, H., Abel Chuang, P.-Y., Pan, M., & Sui, P.-C. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.07.241 · Cited by 88 · cited 9×
“To the best of our knowledge, most catalyst inks usually give a shear-thinning behavior [28,52,53,74]; only a few cases exhibit a nearly Newtonian behavior for shear rate of about 1~1000 s−1 [53,75].”
BackgroundMethodInfluentialMolecular Dynamics Study of Ionomer Adsorption at a Carbon Surface in Catalyst Ink
Mashio, T., Ohma, A., & Tokumasu, T. (2016) · Electrochimica Acta · doi:10.1016/j.electacta.2016.04.004 · Cited by 84
Development of high-performance roll-to-roll-coated gas-diffusion-electrode-based fuel cells
Mauger, S. A., Wang, M., Cetinbas, F. C., Dzara, M. J., Park, J., Myers, D. J., Ahluwalia, R. K., Pylypenko, S., Hu, L., Litster, S., et al. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.230039 · Cited by 84 · cited 27×
“The CCM-based MEAs exhibit a superior performance in some studies due to excellent interfacial contact between the CL and membrane [167], while the GDE-based MEAs perform better in others [75].”
BackgroundMethodInfluentialXu, F., Zhang, H., Ilavsky, J., Stanciu, L., Ho, D., Justice, M. J., Petrache, H. I., & Xie, J. (2010) · Langmuir · doi:10.1021/la1028228 · Cited by 82
Dispersion of Rod-like Particles of Nafion in Salt-Free Water/1-Propanol and Water/Ethanol Solutions
Yamaguchi, M., Matsunaga, T., Amemiya, K., Ohira, A., Hasegawa, N., Shinohara, K., Ando, M., & Yoshida, T. (2014) · The Journal of Physical Chemistry B · doi:10.1021/jp506814m · Cited by 81
High-Resolution Analysis of Ionomer Loss in Catalytic Layers after Operation
Morawietz, T., Handl, M., Oldani, C., Gazdzicki, P., Hunger, J., Wilhelm, F., Blake, J., Friedrich, K. A., & Hiesgen, R. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0151806jes · Cited by 81
Gravure coating for roll-to-roll manufacturing of proton-exchange-membrane fuel cell catalyst layers
Mauger, S. A., Neyerlin, K. C., Yang-Neyerlin, A. C., More, K. L., & Ulsh, M. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0091813jes · Cited by 81 · cited 9×
“However, for screen printing, slot-die coating, or gravure coating, the viscosity of the catalyst ink needs to be increased [38,39].”
BackgroundMethodInfluentialAhn, C.-Y., Jang, S., Cho, Y.-H., Choi, J., Kim, S., Kim, S. M., Sung, Y.-E., & Choi, M. (2018) · Scientific Reports · doi:10.1038/s41598-018-19861-6 · Cited by 80
Simulation of capillary shrinkage cracking in cement-like materials
Slowik, V., Hübner, T., Schmidt, M., & Villmann, B. (2009) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2009.05.004 · Cited by 79
Fuel cell catalyst layers containing short-side-chain perfluorosulfonic acid ionomers
Peron, J., Edwards, D., Haldane, M., Luo, X., Zhang, Y., Holdcroft, S., & Shi, Z. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2010.06.050 · Cited by 77
Zeng, Y., Zhang, H., Wang, Z., Jia, J., Miao, S., Song, W., Xiao, Y., Yu, H., Shao, Z., & Yi, B. (2018) · Journal of Materials Chemistry A · doi:10.1039/c7ta10901f · Cited by 77 · cited 2×
“However, most structureordered CLs are susceptible to topple over [14,18], thus losing their ordered structure during the decal or hot-pressing process.”
BackgroundTakahashi, S., Shimanuki, J., Mashio, T., Ohma, A., Tohma, H., Ishihara, A., Ito, Y., Nishino, Y., & Miyazawa, A. (2016) · Electrochimica Acta · doi:10.1016/j.electacta.2016.12.068 · Cited by 76
Highly durable fuel cell electrodes based on ionomers dispersed in glycerol
Kim, Y. S., Welch, C. F., Mack, N. H., Hjelm, R. P., Orler, E. B., Hawley, M. E., Lee, K. S., Yim, S.-D., & Johnston, C. M. (2014) · Phys. Chem. Chem. Phys. · doi:10.1039/c4cp00496e · Cited by 75
Kusano, T., Hiroi, T., Amemiya, K., Ando, M., Takahashi, T., & Shibayama, M. (2015) · Polymer Journal · doi:10.1038/pj.2015.36 · Cited by 74
Fabrication of a thin catalyst layer using organic solvents
Yang, T.-H., Yoon, Y.-G., Park, G.-G., Lee, W.-Y., & Kim, C.-S. (2004) · Journal of Power Sources · doi:10.1016/j.jpowsour.2003.09.018 · Cited by 74
Dispersion-Solvent Control of Ionomer Aggregation in a Polymer Electrolyte Membrane Fuel Cell
Lee, J. H., Doo, G., Kwon, S. H., Choi, S., Kim, H.-T., & Lee, S. G. (2018) · Scientific Reports · doi:10.1038/s41598-018-28779-y · Cited by 74
Wang, M., Medina, S., Pfeilsticker, J. R., Pylypenko, S., Ulsh, M., & Mauger, S. A. (2019) · ACS Applied Energy Materials · doi:10.1021/acsaem.9b01871 · Cited by 74
Sharma, R., & Andersen, S. M. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b14622 · Cited by 73
Suzuki, T., Tanaka, H., Hayase, M., Tsushima, S., & Hirai, S. (2016) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2016.09.078 · Cited by 72 · cited 9×
“printed from [56], Copyright (2016), with permission from Elsevier).”
BackgroundMethodInfluentialMulticomponent, multiphase interactions in fuel-cell inks
Berlinger, S. A., Garg, S., & Weber, A. Z. (2021) · Current Opinion in Electrochemistry · doi:10.1016/j.coelec.2021.100744 · Cited by 72 · cited 1×
“For the time being, there have been some reviews focused on the optimization of the formulation and dispersion techniques of catalyst ink, the characterization and modeling of catalyst ink, the coating techniques, or the underlying interactions between solvent, ionomer, and catalyst [29,35,43].”
BackgroundLet’s Not Ignore the Ultrasonic Effects on the Preparation of Fuel Cell Materials
Pollet, B. G. (2014) · Electrocatalysis · doi:10.1007/s12678-014-0211-4 · Cited by 70
Wang, C., Cheng, X., Yan, X., Shen, S., Ke, C., Wei, G., & Zhang, J. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.0401904jes · Cited by 69
Van Cleve, T., Wang, G., Mooney, M., Cetinbas, C. F., Kariuki, N., Park, J., Farghaly, A., Myers, D., & Neyerlin, K. C. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228889 · Cited by 66 · cited 1×
“Therefore, Pt/Vulcan has a more uniform ionomer coverage than Pt/Ketjen due to higher Pt surface density [53,59,60].”
BackgroundIntegrating nanostructured Pt-based electrocatalysts in proton exchange membrane fuel cells
Ly, A., Asset, T., & Atanassov, P. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228516 · Cited by 65 · cited 1×
“(2) The amount and charge type of functional groups on carbon [51,85,96]: For example, hydrophobic carbon tends to form large agglomerates in the polar solvent, e.”
BackgroundImpact of Dispersion Solvent on Ionomer Thin Films and Membranes
Berlinger, S. A., Dudenas, P. J., Bird, A., Chen, X., Freychet, G., McCloskey, B. D., Kusoglu, A., & Weber, A. Z. (2020) · ACS Applied Polymer Materials · doi:10.1021/acsapm.0c01076 · Cited by 65
Guo, Y., Yang, D., Li, B., Yang, D., Ming, P., & Zhang, C. (2021) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.1c07070 · Cited by 65 · cited 2×
“The thixotropy of ink could be regulated by varying the dispersion method [28] or adjusting the dielectric constant of solvent or varying I/C ratio [79].”
BackgroundMabuchi, T., Huang, S.-F., & Tokumasu, T. (2020) · Macromolecules · doi:10.1021/acs.macromol.9b02725 · Cited by 64
Evaluation of particle interactions by in situ visualization of separation behaviour
Lerche, D., & Sobisch, T. (2014) · Colloids and Surfaces A: Physicochemical and Engineering Aspects · doi:10.1016/j.colsurfa.2012.10.015 · Cited by 63
Lei, C., Bessarabov, D., Ye, S., Xie, Z., Holdcroft, S., & Navessin, T. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.03.024 · Cited by 62
Ramaswamy, N., Kumaraguru, S., Koestner, R., Fuller, T., Gu, W., Kariuki, N., Myers, D., Dudenas, P. J., & Kusoglu, A. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abe5eb · Cited by 62
Andersen, S. M. (2015) · Applied Catalysis B: Environmental · doi:10.1016/j.apcatb.2015.07.049 · Cited by 61
Densities, Surface Tensions, and Refractive Indices of the Water + 1,3-Propanediol System
Lee, J., Park, S., & Lee, H. J. (1999) · Journal of Chemical & Engineering Data · doi:10.1021/je990196m · Cited by 61
Andersen, S. M., & Grahl-Madsen, L. (2016) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2015.11.101 · Cited by 61 · cited 1×
“% [98], is not appropriate for all catalysts [91,99].”
BackgroundInfluence of ionomer adsorption on agglomerate structures in high-solid catalyst inks
Kumano, N., Kudo, K., Akimoto, Y., Ishii, M., & Nakamura, H. (2020) · Carbon · doi:10.1016/j.carbon.2020.07.047 · Cited by 61 · cited 8×
“To the best of our knowledge, most catalyst inks usually give a shear-thinning behavior [28,52,53,74]; only a few cases exhibit a nearly Newtonian behavior for shear rate of about 1~1000 s−1 [53,75].”
BackgroundMethodInfluentialIntegrated High‐Efficiency Pt/Carbon Nanotube Arrays for PEM Fuel Cells
Zhang, W., Minett, A. I., Gao, M., Zhao, J., Razal, J. M., Wallace, G. G., Romeo, T., & Chen, J. (2011) · Advanced Energy Materials · doi:10.1002/aenm.201100092 · Cited by 59 · cited 1×
“, vertically aligned carbon nanotubes [10,11] or conductive polymer [12,13]), ordered catalysts [14–16], ordered ionomer materials [17], or ordered non-conductive materials (e.”
BackgroundKim, T.-H., Yoo, J. H., Maiyalagan, T., & Yi, S.-C. (2019) · Applied Surface Science · doi:10.1016/j.apsusc.2019.03.113 · Cited by 59
Ahn, C.-Y., Cheon, J.-Y., Joo, S.-H., & Kim, J. (2013) · Journal of Power Sources · doi:10.1016/j.jpowsour.2012.09.012 · Cited by 58 · cited 2×
“% [98], is not appropriate for all catalysts [91,99].”
BackgroundBonifácio, R. N., Paschoal, J. O. A., Linardi, M., & Cuenca, R. (2011) · Journal of Power Sources · doi:10.1016/j.jpowsour.2011.01.010 · Cited by 58 · cited 1×
“5 mN/m (the surface tension value of carbon cloth) [80].”
BackgroundSo, M., Ohnishi, T., Park, K., Ono, M., Tsuge, Y., & Inoue, G. (2019) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2019.09.012 · Cited by 58
Shrivastava, U. N., Fritzsche, H., & Karan, K. (2018) · Macromolecules · doi:10.1021/acs.macromol.8b01240 · Cited by 56
Andersen, S. M., Borghei, M., Dhiman, R., Ruiz, V., Kauppinen, E., & Skou, E. (2014) · The Journal of Physical Chemistry C · doi:10.1021/jp501088d · Cited by 55 · cited 2×
“The equilibrium constant of ionomer adsorption on catalyst decreases with increasing the amount of the surface oxygen-containing groups [96].”
BackgroundSong, C.-H., & Park, J.-S. (2019) · Energies · doi:10.3390/en12030549 · Cited by 54 · cited 1×
“It was reported that cracks [57,58,141] or larger ionomer patches [49] are more likely formed in the CLs made of the ink containing water/2-propanol.”
BackgroundEnabling industrial production of electrodes by use of slot-die coating for HT-PEM fuel cells
Bodner, M., García, H. R., Steenberg, T., Terkelsen, C., Alfaro, S. M., Avcioglu, G. S., Vassiliev, A., Primdahl, S., & Hjuler, H. A. (2019) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2018.11.091 · Cited by 54 · cited 6×
“However, for screen printing, slot-die coating, or gravure coating, the viscosity of the catalyst ink needs to be increased [38,39].”
BackgroundMethodInfluentialChisaka, M., & Daiguji, H. (2006) · Electrochimica Acta · doi:10.1016/j.electacta.2006.01.018 · Cited by 52
Shahgaldi, S., Alaefour, I., Zhao, J., & Li, X. (2018) · Fuel · doi:10.1016/j.fuel.2018.04.076 · Cited by 52
Self-citationYoshimune, W., & Harada, M. (2019) · Chemistry Letters · doi:10.1246/cl.190017 · Cited by 51 · cited 1×
“recently observed that increasing Pt loading on carbon would lead to reduced density and increased thickness of the adsorbed ionomer layer in the water/ethanol-based catalyst ink, due to the hydrophobic interaction between the main chain of ionomer and carbon [90].”
BackgroundSambandam, S., & Ramani, V. (2010) · Physical Chemistry Chemical Physics · doi:10.1039/b921916a · Cited by 49
Jang, S., Kim, S., Kim, S. M., Choi, J., Yeon, J., Bang, K., Ahn, C.-Y., Hwang, W., Her, M., Cho, Y.-H., et al. (2018) · Nano Energy · doi:10.1016/j.nanoen.2017.11.011 · Cited by 45
Kuroki, H., Onishi, K., Asami, K., & Yamaguchi, T. (2019) · Industrial & Engineering Chemistry Research · doi:10.1021/acs.iecr.9b02111 · Cited by 45 · cited 8×
“((a–c) Modified with permission from [156], Copyright (2019), American Chemical Society; (d–e) Reprinted with p rmission from [24], Copyright (2019), America Chemical Society; (f) Reprinted from [159], Copyright (2014), with permission from Elsevier).”
BackgroundMethodInfluentialTalukdar, K., Ripan, M. A., Jahnke, T., Gazdzicki, P., Morawietz, T., & Friedrich, K. A. (2020) · Journal of Power Sources · doi:10.1016/j.jpowsour.2020.228169 · Cited by 45
Effects of Ionomer Carbon Ratio and Ionomer Dispersity on the Performance and Durability of MEAs
Lee, M. ‐., Lee, H. ‐., Yim, S. ‐., Kim, C. ‐., Shul, Y. ‐., Kucernak, A., & Shin, D. (2018) · Fuel Cells · doi:10.1002/fuce.201700178 · Cited by 44
Impact of Nonadsorbed Ionomer on Viscosity of Catalyst Inks for Polymer Electrolyte Fuel Cells
Yoshimune, W., & Harada, M. (2020) · Bulletin of the Chemical Society of Japan · doi:10.1246/bcsj.20190321 · Cited by 44 · cited 4×
“, a low I/C ratio, the ionomer molecules adsorb on the catalyst agglomerates, enhancing the columbic repulsion force and steric hindrance of inter-agglomerates [42,53,74], inhibiting aggregation, to some extent similar to a stabilizing agent, decreasing the agglomerate size, and thus improving the colloidal stability…”
BackgroundInfluentialGomes Bezerra, C. A., Deiner, L. J., & Tremiliosi-Filho, G. (2019) · Advanced Engineering Materials · doi:10.1002/adem.201900703 · Cited by 43 · cited 5×
“The CCM-based MEAs exhibit a superior performance in some studies due to excellent interfacial contact between the CL and membrane [167], while the GDE-based MEAs perform better in others [75].”
BackgroundInfluentialSome Physical Properties of Diacetone Alcohol, Mesityl Oxide and Methyl Isobutyl Ketone
Fuge, E. T. J., Bowden, S. T., & Jones, W. J. (1952) · The Journal of Physical Chemistry · doi:10.1021/j150500a022 · Cited by 41
On the state and stability of fuel cell catalyst inks
Bapat, S., Giehl, C., Kohsakowski, S., Peinecke, V., Schäffler, M., & Segets, D. (2021) · Advanced Powder Technology · doi:10.1016/j.apt.2021.08.030 · Cited by 38
Jiang, S., Yi, B., Cao, L., Song, W., Zhao, Q., Yu, H., & Shao, Z. (2016) · Journal of Power Sources · doi:10.1016/j.jpowsour.2016.08.098 · Cited by 37 · cited 1×
“, vertically aligned carbon nanotubes [10,11] or conductive polymer [12,13]), ordered catalysts [14–16], ordered ionomer materials [17], or ordered non-conductive materials (e.”
BackgroundThoma, M., Lin, W., Hoffmann, E., Sattes, M.-M., Segets, D., Damm, C., & Peukert, W. (2018) · Langmuir · doi:10.1021/acs.langmuir.8b02726 · Cited by 37
Does power ultrasound affect Nafion® dispersions?
Adamski, M., Peressin, N., Holdcroft, S., & Pollet, B. G. (2019) · Ultrasonics Sonochemistry · doi:10.1016/j.ultsonch.2019.104758 · Cited by 37
Bapat, S., & Segets, D. (2020) · ACS Applied Nano Materials · doi:10.1021/acsanm.0c01467 · Cited by 37
Takahashi, K., Kakinuma, K., & Uchida, M. (2016) · Journal of The Electrochemical Society · doi:10.1149/2.0611610jes · Cited by 34
Sun, R., Xia, Z., Shang, L., Fu, X., Li, H., Wang, S., & Sun, G. (2017) · Journal of Materials Chemistry A · doi:10.1039/c7ta02500a · Cited by 34 · cited 1×
“, vertically aligned carbon nanotubes [10,11] or conductive polymer [12,13]), ordered catalysts [14–16], ordered ionomer materials [17], or ordered non-conductive materials (e.”
BackgroundInk Degradation and Its Effects on the Crack Formation of Fuel Cell Catalyst Layers
Uemura, S., Yoshida, T., Koga, M., Matsumoto, H., Yang, X., Shinohara, K., Sasabe, T., & Hirai, S. (2019) · Journal of The Electrochemical Society · doi:10.1149/2.0411902jes · Cited by 34 · cited 4×
“The former includes the oxidation of carbon, ionomer, and organic solvent caused by the catalysis of Pt or dealloying of catalyst during storage, modifying the composition of catalyst ink and as a result, impacting the structure or performance of CL [64,81].”
BackgroundInfluentialFormulation of carbon black-ionomer dispersions for thin film formation in fuel cells
Hoffmann, E., Zhang, S., Thoma, M., Damm, C., & Peukert, W. (2019) · Particuology · doi:10.1016/j.partic.2018.08.001 · Cited by 34 · cited 7×
“modulus of ionomer, decreasing the risk of cracking [74].”
BackgroundMethodInfluentialKim, O. ‐., Oh, S. ‐., Ahn, C. ‐., Kim, S., Kim, J. K., Kim, J., Yang, S., Choi, M., Cho, Y. ‐., & Sung, Y. ‐. (2018) · Fuel Cells · doi:10.1002/fuce.201800083 · Cited by 31
Chisaka, M., Matsuoka, E., & Daiguji, H. (2010) · Journal of The Electrochemical Society · doi:10.1149/1.3439617 · Cited by 30
Sun, C.-N., More, K. L., Veith, G. M., & Zawodzinski, T. A. (2013) · Journal of The Electrochemical Society · doi:10.1149/2.055309jes · Cited by 28
Fluorocarbon-Based Ionomers with Single Acid and Multiacid Side Chains at Nanothin Interfaces
Farzin, S., Sarella, A., Yandrasits, M., & Dishari, S. K. (2019) · The Journal of Physical Chemistry C · doi:10.1021/acs.jpcc.9b10015 · Cited by 28
Impact of DAA/water composition on PFSA ionomer conformation
Hoffmann, E., Fischer, D., Thoma, M., Damm, C., Lobaz, V., Zhigunov, A., & Peukert, W. (2021) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2020.08.058 · Cited by 28
Zhao, N., Shi, Z., & Girard, F. (2021) · Materials · doi:10.3390/ma15010078 · Cited by 28
Effect of Organic Solvents on Catalyst Layer Structure in Polymer Electrolyte Membrane Fuel Cells
Chisaka, M., & Daiguji, H. (2008) · Journal of The Electrochemical Society · doi:10.1149/1.3000592 · Cited by 28
Lee, J. H., Doo, G., Kwon, S. H., Kang, H., Choi, S., Yim, S.-D., Kim, H.-T., & Lee, S. G. (2020) · ACS Applied Polymer Materials · doi:10.1021/acsapm.0c00042 · Cited by 27
Liu, H., Qin, J., Rockward, T., Wu, J., Li, J., Li, G., Mao, Q., Lv, Y., Wang, X., Zhang, S., et al. (2020) · Journal of Materials Chemistry A · doi:10.1039/d0ta07189g · Cited by 27 · cited 2×
“The structure-ordered CLs are usually ultrathin, less than 1 μm or even less than 200 nm in some cases [14,16,20], which will result in inherently low mass transport resistance versus the conventional CLs with a thickness of several μm due to the shorter transport distance.”
BackgroundSelf-citationElectrostatic spraying of membrane electrode for proton exchange membrane fuel cell
Liu, R., Zhou, W., Wan, L., Zhang, P., Li, S., Gao, Y., Xu, D., Zheng, C., & Shang, M. (2020) · Current Applied Physics · doi:10.1016/j.cap.2019.09.016 · Cited by 26
Effect of an Electrospray-Generated Ionomer Morphology on Polymer Electrolyte Fuel Cell Performance
Cho, S., Tamoto, K., & Uchida, M. (2020) · Energy & Fuels · doi:10.1021/acs.energyfuels.0c02337 · Cited by 24
Modeling ionomer swelling dynamics of a sulfonated polyphenylene, pentablock copolymers, and nafion
Wang, D., & Cornelius, C. J. (2017) · Journal of Polymer Science Part B Polymer Physics · doi:10.1002/polb.24284 · Cited by 21
Choi, M., Kim, J. K., Kim, J., Yang, S., Park, J.-E., Kim, O.-H., & Cho, Y.-H. (2018) · RSC Advances · doi:10.1039/c8ra07754a · Cited by 21
Effect of catalytic ink on sub-freezing endurance of PEMFCs
Song, W., Yu, H., Hao, L., Yi, B., & Shao, Z. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.07.041 · Cited by 20
Zhao, J., Li, X., & Liu, Z. (2019) · International Journal of Energy Research · doi:10.1002/er.4671 · Cited by 20 · cited 3×
“, molecular dynamic simulation [118] or discrete element method [40].”
BackgroundMethodSelf-citationSo, S., Kang, H., Choi, D., & Oh, K.-H. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.05.128 · Cited by 20
Fabrication of MEA with hydrocarbon based membranes using low temperature decal method for DMFC
Krishnan, N. N., Prabhuram, J., Hong, Y., Kim, H.-J., Yoon, K.-S., Ha, H. Y., Lim, T.-H., & Kim, S. (2010) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2010.03.023 · Cited by 19
Yang, F., Xin, L., Uzunoglu, A., Stanciu, L., Ilavsky, J., Son, S., & Xie, J. (2016) · ECS Transactions · doi:10.1149/07514.0361ecst · Cited by 19
Li, J. S., Tang, H., Chen, R., Liŭ, D., Xie, Z., Pan, M., & Jiang, S. P. (2015) · Journal of Materials Chemistry A · doi:10.1039/c5ta02190a · Cited by 17 · cited 1×
“, vertically aligned carbon nanotubes [10,11] or conductive polymer [12,13]), ordered catalysts [14–16], ordered ionomer materials [17], or ordered non-conductive materials (e.”
BackgroundSwelling agent adopted decal transfer method for membrane electrode assembly fabrication
Cho, D. H., Lee, S. Y., Shin, D. W., Hwang, D. S., & Lee, Y. M. (2014) · Journal of Power Sources · doi:10.1016/j.jpowsour.2014.02.037 · Cited by 15
New Fuel Cell Membranes with Improved Durability and Performance
Yandrasits, M., & USDOE Office of Energy Efficiency and Renewable Energy (EERE) (2017) · OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) · doi:10.2172/1415145 · Cited by 13
Li, W., Bi, X., Luo, M., & Sui, P.-C. (2021) · Journal of The Electrochemical Society · doi:10.1149/1945-7111/abe725 · Cited by 12 · cited 4×
“, 15 mPa s [68]), increasing the viscosity of ink will decrease the number of large droplets and increase the uniformity of the formed droplets, enhancing spraying quality.”
BackgroundInfluentialDevivaraprasad, R., & Masuda, T. (2020) · Langmuir · doi:10.1021/acs.langmuir.0c02023 · Cited by 11 · cited 1×
“The morphology, size, and conformation of the ionomer agglomerates dispersed will differ with the water fraction or the type of alcohol, altering the CLs’ structure and their performance [25,30,32,49,57,131,137,140].”
BackgroundChoi, S.-H., Jung, D.-W., Yoon, S.-O., Park, S., Oh, E.-S., & Kim, J. (2011) · Metals and Materials International · doi:10.1007/s12540-011-1019-x · Cited by 10 · cited 1×
“, nanopore volume [88]) or Pt loading on carbon [92,93] will impact the optimal I/C ratio; certainly, the optimal I/C ratio also depends on the type of ionomer (discussed more in Section 4.”
BackgroundFactors influencing slurry rheology
Benretem, A., Benidir, M., & Chaib, R. (2010) · World Pumps · doi:10.1016/s0262-1762(10)70199-1 · Cited by 9 · cited 1×
“For a certain solid content, the ink viscosity usually increases with decreasing the size of agglomerates [28,69].”
BackgroundCommunication—Investigation of catalyst ink degradation by X-ray CT
Uemura, S., Kameya, Y., Iriguchi, N., Yoshida, T., Shinohara, K., & Hirai, S. (2018) · Journal of The Electrochemical Society · doi:10.1149/2.0411803jes · Cited by 9 · cited 1×
“The former includes the oxidation of carbon, ionomer, and organic solvent caused by the catalysis of Pt or dealloying of catalyst during storage, modifying the composition of catalyst ink and as a result, impacting the structure or performance of CL [64,81].”
BackgroundOptimum ratio between Nafion and 20, 40 wt% Pt/C catalysts for MEAs
Jung, J.-H., Jung, D.-W., & Kim, J.-B. (2011) · Journal of the Korean Electrochemical Society · doi:10.5229/jkes.2011.14.1.050 · Cited by 8 · cited 1×
“, nanopore volume [88]) or Pt loading on carbon [92,93] will impact the optimal I/C ratio; certainly, the optimal I/C ratio also depends on the type of ionomer (discussed more in Section 4.”
BackgroundSolvation and Gelation Process of Nafion
Kim, Y. S., Labouriau, A., Welch, C. F., et al. (2013) · ECS Meeting Abstracts · doi:10.1149/ma2013-02/15/1390 · Cited by 5
Investigation of Catalyst Ink Dispersion Using Small Angle X-ray and Small Angle Neutron Scattering
Xu, F., Zhang, H., Ho, D., Ilavský, J., Justics, M., Petrache, H. I., Stanciu, L., & Xie, J. (2010) · ECS Transactions · doi:10.1149/1.3484625 · Cited by 5
Carine, T., & Christine, N.-C. (2020) · Nanomaterials Science & Engineering · doi:10.34624/nmse.v2i3.19554 · Cited by 4
Tailoring of Electrocatalyst Inks for Performance Enhancement in Proton Exchange Membrane Fuel Cells
Bapat, S., Fricke, S., Kohsakowski, S., Goessling, S., Peinecke, V., & Segets, D. (2020) · ECS Transactions · doi:10.1149/09707.0651ecst · Cited by 3
Modeling the Flow Behavior of Catalyst Inks for PEM Fuel Cells by an Evolutionary Algorithm
Ney, L., Singh, R., Göttlicher, N., et al. (2021) · Publikationsdatenbank der Fraunhofer-Gesellschaft (Fraunhofer-Gesellschaft) · doi:10.13140/rg.2.2.20968.19209 · Cited by 2
Self-citationYang, F., Xin, L., Uzunoğlu, A., Stanciu, L., Ilavský, J., Son, S. F., & Xie, J. (2016) · ECS Meeting Abstracts · doi:10.1149/ma2016-02/38/2698 · Cited by 1
Effect of Pt and Ionomer Distribution on Cell Performance and Durability
Kobayashi, A., Uchida, M., Kakinuma, K., & Fujii, T. (2021) · ECS Meeting Abstracts · doi:10.1149/ma2021-02391177mtgabs · Cited by 1
Effect of Electrospray-Generated Ionomer Morphology on Polymer Electrolyte Fuel Cell Performance
Cho, S., Tamoto, K., & Uchida, M. (2020) · ECS Meeting Abstracts · doi:10.1149/ma2020-02332117mtgabs
Takahashi, S., Shimanuki, J., Mashio, T., Ohma, A., Tohma, H., Ishihara, A., Ito, Y., Nishino, Y., & Miyazawa, A. (2016) · ECS Meeting Abstracts · doi:10.1149/ma2016-02/38/2594
Zhang, W., Minett, A. I., Gao, M., Zhao, J., Razal, J. M., Wallace, G. G., Romeo, T., & Chen, J. (2011) · Advanced Energy Materials · doi:10.1002/aenm.201190020
(Invited) Catalyst Layer Interactions That Affect Coatability
Dixit, M., Harkey, B., Shen, F., & Hatzell, K. B. (2018) · ECS Meeting Abstracts · doi:10.1149/ma2018-02/41/1392
Research works printed but not linked: 3
- Bird, B.R., Armstrong, R.C., and Hassager, O. (1987). Dynamics of Polymeric Liquids, Volume 1: Fluid Mechanics, Wiley-Interscience. [2nd ed.].
- (2022, March 21). Ion Exchange Materials. Available online: https://www.fuelcellearth.com/wp-content/uploads/converted_files/pdf/D520-D521-D1021-D2020-D2021-Product-Bulletin-Chemours.pdf.
- Rumble, J.R. (2017). CRC Handbook of Chemistry and Physics, CRC Press Taylor & Francis Group.
Cited by
(2023) · doi:10.1038/s41929-023-00949-w · Cited by 195
Bierling, M., McLaughlin, D., Mayerhöfer, B., & Thiele, S. (2023) · Advanced Energy Materials · doi:10.1002/aenm.202203636 · Cited by 59
Murugaiah, D. K., & Shahgaldi, S. (2024) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2024.04.036 · Cited by 60
Liu, P., Yang, D., Li, B., Zhang, C., & Ming, P. (2023) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2023.02.022 · Cited by 49
Liu, G., McLaughlin, D., Thiele, S., & Pham, C. V. (2022) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.141757 · Cited by 46
Metadata
- Authors
- Liu, H., Ney, L., Zamel, N., & Li, X.
- Affiliations
- University of Waterloo (CA)
- Fraunhofer Institute for Solar Energy Systems (DE)
- Corresponding author
- Zamel, Nada
- Li, Xianguo
- Venue
- Applied Sciences
- Publisher
- MDPI AG
- Published
- 2022-04-08
- Volume
- 12
- Issue
- 8
- Pages
- 3776
- ISSN
- 2076-3417 (ISSN-L)
- OpenAlex
- W4224267685
- Cited by
- 85
- References
- 171
- Citations by year
- 2026: 21 · 2025: 26 · 2024: 26 · 2023: 11 · 2022: 1
- FWCI
- 4.38
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Applied Sciences (publishedVersion, cc-by)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion)
- Fraunhofer-Publica (Fraunhofer-Gesellschaft) (submittedVersion, cc-by)
- Fraunhofer-Publica (Fraunhofer-Gesellschaft)
- Funders
- Canadian Urban Transit Research and Innovation Consortium (160028)
- the Ministry of the Environment, Climate, Protection and the Energy Sector Baden-Württemberg (L75 20113)
- German National Innovation Program Hydrogen and Fuel Cell Technology and The Federal Ministry of Transport and Digital Infrastructur (03B11018A)
- Topics
- Physical Sciences › Engineering › Electrical and Electronic Engineering › Fuel Cells and Related Materials
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Electrocatalysts for Energy Conversion
- Physical Sciences › Materials Science › Materials Chemistry › Advancements in Solid Oxide Fuel Cells
- Keywords
- catalyst layer, proton exchange membrane fuel cells, catalyst ink, multiscale structure, ionomers, catalyst dispersion, coating application, drying, membrane electrode assembly, ink aging, catalyst microstructure
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-09-28, under version 3 of the claim definition (prompt extract-v3).
A second model labelled each claim on 2026-09-28 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.