The DOI matches its Crossref record; 93 of the 93 references it cites were found in a registry or an index; 26 of the 91 sources its claims cite were checked for support.
Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production
Open accessAbstract
This comprehensive review explores silica aerogels and their application in environmental remediation. Due to rapid growth in the consumption of energy and water resources, the purification of contaminated resources for use by humankind should be considered important. The primary objectives of this review are to assess the evolving landscape of silica aerogels, their preparation, and drying techniques, and to discuss the main findings from a wide range of empirical studies and theoretical perspectives. Based on a significant amount of research, this review provides information about aerogels’ capabilities as an adsorbent and catalyst. The analysis spans a variety of contexts for the generation of hydrogen and the degradation of the dyes employed in industry, showing better performance in environmental remediation. The implications of this review point to the need for well-informed policies, innovative synthesis strategies, and ongoing research to harness the full potential for environmental management.
Overview
CoChat Summary
TL;DR
This review argues that silica aerogels are promising materials for environmental remediation and hydrogen production via catalytic or photocatalytic water splitting, owing to their high porosity and surface area. It surveys synthesis and drying methods, electrocatalysis metrics, and dye adsorption, while noting cost, dust, and limited catalyst-loading literature as barriers.
Key findings
- Silica aerogels have high porosity often above 80 vol% and specific surface area around 100–1000 m²/g; cross-linked pores range from 5 to 100 nm with an average diameter of 20–40 nm. Conventional silica aerogel density is about 0.120 g/cm³; densities below 0.090 g/cm³ are not brittle, while they become brittle at 0.150 g/cm³.
- In hydrogen generation, a cobalt-based silica aerogel (Co/SAG) nanocomposite showed a hydrogen generation rate surpassing Co/MCM-41 by 41%; TiO₂@SiO₂ composites demonstrated H₂ production rates about three-times greater than P25 TiO₂; Pt/Ru-promoted TiO₂ on mesoporous silica had a surface area of 140.6 m²/g and a hydrogen yield of 4791.43 μmol/h/g TiO₂, reported as 30-times greater than P25 (161 mmol/h/g TiO₂); CP-APTES-HCl silica aerogel produced 1860 mL min⁻¹ g⁻¹ of hydrogen at 298 K.
- For dye adsorption, hydrophilic silica aerogel (HSA) removed 98% of dyes; mesocellular silica foam pore diameter and pore volume decreased from 9.34 nm and 1.36 cm³ g⁻¹ to 8.03 nm and 0.67 cm³ g⁻¹ after methylene blue adsorption, with surface area decreasing from 585 to 399 m² g⁻¹; laccase with ABTS increased decolorization of Indigo and Alizarin red by 73% and 97%, respectively.
- Proposed activity descriptors for silica-based aerogels in water splitting include surface area and porosity, hydrophilicity and surface functionalization, electronic band structure, charge carrier dynamics and photocatalytic efficiency, stability and reusability, and metal/oxide doping effects.
Methods
- Comprehensive narrative review of silica aerogels, their preparation, drying techniques, and applications in environmental remediation, hydrogen generation, and dye degradation; no primary experiments are reported.
- Synthesizes empirical studies and theoretical perspectives, covering sol–gel chemistry, aging, drying methods, electrocatalysis parameters (overpotential, Tafel slope, current density, Faraday efficiency, turnover frequency, stability), and characterization techniques.
- No systematic search strategy, inclusion criteria, or meta-analysis is stated in the provided text.
Limitations
- Stated: existing literature on SiO₂ aerogels for catalyst loading is quite limited; cost remains significantly greater than traditional insulation materials; dust generated during production is difficult to eliminate; viability for sorption systems cannot be determined until dynamic adsorption/desorption under practical working conditions is examined.
- Stated: all three drying techniques have disadvantages and restrictions; supercritical drying requires high pressure and temperature and raises safety concerns; CO₂ supercritical drying is prolonged.
- Evident: as a narrative review, it lacks a systematic review protocol and quantitative synthesis; several claims rely on cited studies without detailed methods, and some section headings in the provided text are empty or fragmented.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures

![Figure 2 Electron microscope image of highly porous, continuous 3D network structure of aerogel layer (reprinted from S Alwin et al. [3] with permission. Copyright 2020, Spinger nature).](https://figures.cochat.ai/paper-figures/9d631bff55894e7886dbfe2aec27c721/silica-aerogels-as-a-promising-vehicle-for-effective-water-splitting-for-figure-2.jpg)



![Figure 6 Phase diagram of liquid to convert into gel network (reprinted from Suhail Ahmad, Sameer Ahmad, Javed Nabibaksha Sheikh [11] with permission. Copyright 2023, Elsevier).](https://figures.cochat.ai/paper-figures/abfc60e0e81941a7b916ea31ef5b1568/silica-aerogels-as-a-promising-vehicle-for-effective-water-splitting-for-figure-6.jpg)
![Figure 7 Phase diagram for freeze-drying of water (reprinted from Robert Ettema, Gokhan Kirkil, Steven Daly [40] with permission. Copyright 2009, Elsevier).](https://figures.cochat.ai/paper-figures/c74f8673d6fd4943b21c07249b4be9bd/silica-aerogels-as-a-promising-vehicle-for-effective-water-splitting-for-figure-7.jpg)

![Figure 9 Traditional SEM image of Si aerogels alongside a schematic depiction of primary and secondary silica particles (left); (1) neck development process of secondary silica particles and (2) comparative aging rate as a function of time for two mechanisms (a, b) (reprinted from S. Ahmad et al., [11] with permission. Copyright 2023, Elsevier).](https://figures.cochat.ai/paper-figures/1210910c015942188c0d94bc0953150a/silica-aerogels-as-a-promising-vehicle-for-effective-water-splitting-for-figure-9.jpg)




Verification
Claims the paper makes
16 Valid · 6 Not valid · 49 Not checked · 3 Own results and interpretations
At least one cited source doesn’t support this claim or points to a different paper, and none confirmed it — see the verdicts below.
In the paper
“Nonetheless, ambient pressure drying is a relatively straightforward and cost-effective method for producing aerogels on a large scale [4].”
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 4. Drying > 4.2. Ambient Pressure
What the sources say
- Disputedcites [4] Akhter, 2021, Silica Aerogels; a Review of Synthesis, Applications and Fabrication of Hybrid Composites, J. Porous Mater. sourceExperimental — accuracy not yet measured
Section 2.3.2 (Ambient pressure drying) calls APD cheaper than supercritical drying, but says it requires surface modification and other processing steps. It explicitly says the processing time and chemical use make APD too costly for large-scale production, contrary to the cited claim. (LLM, conf=0.90)
Checked by a reasoning model — may be wrong.
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Disputed
Every source the paper cites for this claim was checked and supports it.
In the paper
“The renewable energy performance of the system for electrolysis is increased by applying electrocatalysts.”
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 7. Fundamentals of Catalysis > 7.1. Catalysis
What the sources say
- Supportedcites [50] Aslam, 2023, Electrochemical Hydrogen Production: Sustainable Hydrogen Economy, Green Chem. source
Section 2.1, “Electrocatalysts for hydrogen production,” states that using electrocatalysts increases an electrolysis system’s energy efficiency. This supports the citing sentence’s claim about improved energy performance. (LLM, conf=0.91)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“The primary variables that impact the characteristics of electrocatalyst atom rearrangements include the influence of surface roughness, identification of catalytic center sites, phase transitions, and on the catalytic surface that occur during electrochemical processes [62,63].”
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 8. Aerogel as Catalyst > 8.1. Aerogel as an Electrocatalyst
What the sources say
- Could not verifycites [62] Khan, 2018, Recent Progresses in Electrocatalysts for Water Electrolysis, Electrochem. Energy Rev. sourceExperimental — accuracy not yet measured
Section 4.1 discusses how morphology affects electrocatalytic performance, and section 4.3 says active centres cannot yet be identified accurately. Neither passage addresses atom rearrangements or identifies surface roughness, active-site identification, and phase transitions as variables affecting them. Searches for atom rearrangements and surface reconstruction did not find a passage establishing that claim. (LLM, conf=0.70)
- Not checked — no full text of the sourcecites [63] Zinola, 2012, Electrocatalysis: Fundamentals and Applications, Int. J. Electrochem. source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The sources with a verdict support this claim; the rest weren’t checked yet, have no full text we could read, or their verdicts aren’t rated yet.
In the paper
“The higher the exchange current density, the more effective the electrocatalyst; the type of electrocatalyst is temperature-dependent, and the intrinsic rate of reaction transfer between the electrode and electrolyte is under equilibrium conditions [60,73,74].”
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 8. Aerogel as Catalyst > 8.1. Aerogel as an Electrocatalyst
What the sources say
- Supportedcites [60] Raveendran, 2023, A Comprehensive Review on the Electrochemical Parameters and Recent Material Development of Electrochemical Water Splitting Electrocatalysts, RSC Adv. source
The “Tafel slope and exchange current density” section directly states that a higher exchange current density indicates a better electrocatalyst. It also describes the density as reflecting the intrinsic reaction-transfer rate at equilibrium and as dependent on the electrocatalyst material, solution analyte, and temperature. (LLM, conf=0.95)
- Not checked — no full text of the sourcecites [73] Ďurovič, M., Hnát, J., and Bouzek, K. (2021). Electrocatalysts for the Hydrogen Evolution Reaction in Alkaline and Neutral Media. A Comparative Review. J. Power Sources, 493. source
- Not checked — no full text of the sourcecites [74] Wen, 2023, Electrocatalysts for the Oxygen Evolution Reaction: Mechanism, Innovative Strategies, and Beyond, Mater. Chem. Front. source
plainstates an association- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“These materials have been widely reported and hold high promise for use in electrochemical water splitting.”
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 7. Fundamentals of Catalysis > 7.1. Catalysis
What the sources say
- Could not verifycites [24] Niculescu, A.G., Tudorache, D.I., Bocioagă, M., Mihaiescu, D.E., Hadibarata, T., and Grumezescu, A.M. (2024). An Updated Overview of Silica Aerogel-Based Nanomaterials. Nanomaterials, 14. sourceExperimental — accuracy not yet measured
The Environmental Applications section discusses water decontamination and CO₂ capture, not electrochemical water splitting. Searches for water-splitting electrocatalysts and the listed non-precious material classes found no passage in our copy addressing their promise for that use. (LLM, conf=0.76)
- Could not verifycites [25] Normal, M.T., Amor, N., Ali, A., Petrik, S., Coufal, R., Adach, K., and Fijalkowski, M. (2021). Aerogels for Biomedical, Energy and Sensing Applications. Gels, 7. sourceExperimental — accuracy not yet measured
The 'Aerogels for Energy' section discusses aerogels for supercapacitors and batteries, but does not address the listed non-precious alternatives for electrochemical water splitting. Searches for those materials and for water-splitting electrocatalysts found no passage supporting that application in our copy. (LLM, conf=0.74)
- Not checked — no full text of the sourcecites [26] Smirnova, 2018, Aerogel Production: Current Status, Research Directions, and Future Opportunities, J. Supercrit. Fluids source
- Not checked — no full text of the sourcecites [27] Sharma, 2023, Aerogel Composites and Blankets with Embedded Fibrous Material by Ambient Drying: Reviewing Their Production, Characteristics, and Potential Applications, Dry. Technol. source
- Could not verifycites [28] Danks, 2016, The Evolution of “sol-Gel” Chemistry as a Technique for Materials Synthesis, Mater. Horiz. sourceExperimental — accuracy not yet measured
The passages on non-oxide sol-gel chemistry (section 6) describe synthesizing sulfides, nitrides, and carbides, while the gelatin passage (section 5.2.6) mentions composites with potential applications in catalysis. Neither those passages nor searches for electrochemical water splitting and electrocatalysis address whether the listed non-precious materials are widely reported or promising for electrochemical water splitting. Page numbers were not available in our copy. (LLM, conf=0.75)
- Not checked — no full text of the sourcecites [29] Sarvalkar, 2022, A Review on Multifunctional Nanotechnological Aspects in Modern Textile, J. Text. Inst. source
- Could not verifycites [30] Rashid, 2023, Silica Aerogel: Synthesis, Characterization, Applications, and Recent Advancements, Part. Part. Syst. Charact. sourceExperimental — accuracy not yet measured
Section 4.2.5 (Battery Applications; page unavailable) discusses silica-aerogel battery separators and electrolytes, while Section 4.4.3 (Gas-Phase Catalyst; page unavailable) discusses other catalytic reactions. Searches for water splitting and the listed non-precious catalyst classes found no passage assessing their promise for electrochemical water splitting. (LLM, conf=0.74)
- Not checked — no full text of the sourcecites [31] Banoth, 2022, Introduction to Electrocatalysts, ACS Symp. Ser. source
boosted- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
11 more claims · 1 with their cited sources checked
Create a free account to see all 74 claims and every source verdict.
- It may state two separate claims as one. 35
- Probably not a substantial claim. 36
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 4. Drying
“There are four main drying methods:”
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 4. Drying
“(e) Vacuum drying is used for wet gels, which enhance the high surface area and create large pore sizes in the gels. (f) Microwave drying is employed for structures with mesoporous and microporous 3D cross-linked gels, which also helps to reduce the drying time [24].”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 4. Drying
“As there is no capillary action in this final step of drying, the absence of a liquid–vapor interface is observed.”
§ Silica Aerogels as a Promising Vehicle for Effective Water Splitting for Hydrogen Production > 4. Drying > 4.3. Supercritical Drying
“As there is no capillary action in this final step of drying, a liquid–vapor interface is observed.”
Cited works that were retracted
Works this paper cites that were later retracted, from the retraction notices publishers deposit. Major when the notice came out before this paper was published.
A note, not an issue: for example, a cited work that was retracted only after this paper was published, which its authors could not have known.
In the paper
“Khan, 2024, Exploring the Versatility of Aerogels: Broad Applications in Biomedical Engineering, Astronautics, Energy Storage, Biosensing, and Current Progress, Heliyon, 10, e23102, 10.1016/j.heliyon.2023.e23102”
Cited work 10.1016/j.heliyon.2023.e23102 · retracted 2026-03-16 · notice 10.1016/j.heliyon.2026.e44744 · this paper published 2025-03-08
Citations
Cites
1 retracted
Khan, N. R., Sharmin, T., & Rashid, A. B. (2023) · Heliyon · doi:10.1016/j.heliyon.2023.e23102 · Cited by 98
RetractedChemistry of Aerogels and Their Applications
Pierre, A. C., & Pajonk, G. M. (2002) · Chemical Reviews · doi:10.1021/cr0101306 · Cited by 2,239 · cited 2×
“For instance, in SiO 2 , trivalent Al 3+ cations can be used in place of tetravalent Si 4+ cations to utilize a tetrahedral Si site [61].”
The Evolution of “sol-Gel” Chemistry as a Technique for Materials Synthesis
Danks, A. E., Hall, S. R., & Schnepp, Z. (2016) · Materials Horizons · doi:10.1039/c5mh00260e · Cited by 1,718
Yan, Y., Xia, B. Y., Zhao, B., & Wang, X. (2016) · Journal of Materials Chemistry A · doi:10.1039/c6ta08075h · Cited by 1,368
Raveendran, A., Chandran, M., & Dhanusuraman, R. (2023) · RSC Advances · doi:10.1039/d2ra07642j · Cited by 892
Silica Aerogel: Synthesis and Applications
Gurav, J. L., Jung, I.-K., Park, H.-H., Kang, E. S., & Nadargi, D. Y. (2010) · Journal of Nanomaterials · doi:10.1155/2010/409310 · Cited by 756 · cited 2×
“12 of 28 Scheme 1 shows the hydrolysis and reaction of condensation [44–46]. trifunctional silicon alkoxides is conducted under suitable circumstances.”
An Overview on Silica Aerogels Synthesis and Different Mechanical Reinforcing Strategies
Maleki, H., Durães, L., & Portugal, A. (2014) · Journal of Non-Crystalline Solids · doi:10.1016/j.jnoncrysol.2013.10.017 · Cited by 740
Recent development in electrocatalysts for hydrogen production through water electrolysis
Anwar, S., Khan, F., Zhang, Y., & Djire, A. (2021) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2021.06.191 · Cited by 652
Tailoring Mechanical Properties of Aerogels for Aerospace Applications
Randall, J. P., Meador, M. A. B., & Jana, S. C. (2011) · ACS Applied Materials & Interfaces · doi:10.1021/am200007n · Cited by 579
Recent Progresses in Electrocatalysts for Water Electrolysis
Khan, M. A., Zhao, H., Zou, W., Chen, Z., Cao, W., Fang, J., Xu, J., Zhang, L., & Zhang, J. (2018) · Electrochemical Energy Reviews · doi:10.1007/s41918-018-0014-z · Cited by 527
Hydrogen society: from present to future
Guan, D., Wang, B., Zhang, J., Shi, R., Jiao, K., Li, L., Wang, Y., Xie, B., Zhang, Q., Yu, J., et al. (2023) · Energy & Environmental Science · doi:10.1039/d3ee02695g · Cited by 524
A Special Material or a New State of Matter: A Review and Reconsideration of the Aerogel
Du, A., Zhou, B., Zhang, Z., & Shen, J. (2013) · Materials · doi:10.3390/ma6030941 · Cited by 481
Ďurovič, M., Hnát, J., & Bouzek, K. (2021) · Journal of Power Sources · doi:10.1016/j.jpowsour.2021.229708 · Cited by 436
Linhares, T., Pessoa de Amorim, M. T., & Durães, L. (2019) · Journal of Materials Chemistry A · doi:10.1039/c9ta04811a · Cited by 366
Aerogel Production: Current Status, Research Directions, and Future Opportunities
Smirnova, I., & Gurikov, P. (2018) · The Journal of Supercritical Fluids · doi:10.1016/j.supflu.2017.12.037 · Cited by 300
Electrocatalytic Water Splitting Mechanism and Electrocatalyst Design
Wu, H., Huang, Q., Shi, Y., Chang, J., & Lu, S. (2023) · Nano Research · doi:10.1007/s12274-023-5502-8 · Cited by 295
Distinct Approaches of Removal of Dyes from Wastewater: A Review
Bal, G., & Thakur, A. (2022) · Materials Today Proceedings · doi:10.1016/j.matpr.2021.09.119 · Cited by 285 · cited 1×
“…have the potential to negatively impact aquatic ecosystems and inhibit the penetration of sunlight into water, thereby slowing down the process of photosynthesis. of dye in water The concentration of dye in water needs to be either removed or lowered to an acceptable level prior to drainage [15].”
Theoretical Advances in Understanding and Designing the Active Sites for Hydrogen Evolution Reaction
Sun, F., Tang, Q., & Jiang, D.-E. (2022) · ACS Catalysis · doi:10.1021/acscatal.2c02081 · Cited by 285
Vidas, L., & Castro, R. (2021) · Applied Sciences · doi:10.3390/app112311363 · Cited by 269
Electrochemical Hydrogen Production: Sustainable Hydrogen Economy
Aslam, S., Rani, S., Lal, K., Fatima, M., Hardwick, T., Shirinfar, B., & Ahmed, N. (2023) · Green Chemistry · doi:10.1039/d3gc02849f · Cited by 263
Computational chemistry for water-splitting electrocatalysis
Miao, L., Jia, W., Cao, X., & Jiao, L. (2024) · Chemical Society Reviews · doi:10.1039/d2cs01068b · Cited by 241
Karamikamkar, S., Naguib, H. E., & Park, C. B. (2020) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2020.102101 · Cited by 207
Synthesis, Drying Process and Medical Application of Polysaccharide-Based Aerogels
El-Naggar, M. E., Othman, S. I., Allam, A. A., & Morsy, O. M. (2020) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2019.10.037 · Cited by 197
Quaternized Magnetic Microspheres for the Efficient Removal of Reactive Dyes
Shuang, C., Li, P., Li, A., Zhou, Q., Zhang, M., & Zhou, Y. (2012) · Water Research · doi:10.1016/j.watres.2012.05.052 · Cited by 164
Aerogels: Promising Nanostructured Materials for Energy Conversion and Storage Applications
Alwin, S., & Sahaya Shajan, X. (2020) · Materials for Renewable and Sustainable Energy · doi:10.1007/s40243-020-00168-4 · Cited by 157
Parale, V. G., Kim, T., Choi, H., Phadtare, V. D., Dhavale, R. P., Kanamori, K., & Park, H. (2024) · Advanced Materials · doi:10.1002/adma.202307772 · Cited by 146
An overview on alumina-silica-based aerogels
Almeida, C. M. R., Ghica, M. E., & Durães, L. (2020) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2020.102189 · Cited by 132
Multifunctional Aerogels: A comprehensive review on types, synthesis and applications of aerogels
Sonu, S. S., Rai, N., & Chauhan, I. (2023) · Journal of Sol-Gel Science and Technology · doi:10.1007/s10971-022-06026-1 · Cited by 132
Silica Aerogels; a Review of Synthesis, Applications and Fabrication of Hybrid Composites
Akhter, F., Soomro, S. A., & Inglezakis, V. J. (2021) · Journal of Porous Materials · doi:10.1007/s10934-021-01091-3 · Cited by 131
Synergistic effects of silica aerogels/xerogels on properties of polymer composites: A review
Kaya, G. G., & Deveci, H. (2020) · Journal of Industrial and Engineering Chemistry · doi:10.1016/j.jiec.2020.05.019 · Cited by 128
Flexible and Transparent Silica Aerogels: An Overview
Parale, V. G., Lee, K.-Y., & Park, H.-H. (2017) · Journal of the Korean Ceramic Society · doi:10.4191/kcers.2017.54.3.12 · Cited by 113
Domínguez, M., Taboada, E., Idriss, H., Molins, E., & Llorca, J. (2010) · Journal of Materials Chemistry · doi:10.1039/c0jm00184h · Cited by 111
An Updated Overview of Silica Aerogel-Based Nanomaterials
Niculescu, A.-G., Tudorache, D.-I., Bocioagă, M., Mihaiescu, D. E., Hadibarata, T., & Grumezescu, A. M. (2024) · Nanomaterials · doi:10.3390/nano14050469 · Cited by 109
Electrocatalysts for the Oxygen Evolution Reaction: Mechanism, Innovative Strategies, and Beyond
Wen, N., Jiao, X., Xia, Y., & Chen, D. (2023) · Materials Chemistry Frontiers · doi:10.1039/d3qm00423f · Cited by 104
Yu, J., Li, Z., Liu, T., Zhao, S., Guan, D., Chen, D., Shao, Z., & Ni, M. (2023) · Chemical Engineering Journal · doi:10.1016/j.cej.2023.141674 · Cited by 99
Silica Centered Aerogels as Advanced Functional Material and Their Applications: A Review
Ahmad, S., Ahmad, S., & Sheikh, J. N. (2023) · Journal of Non-Crystalline Solids · doi:10.1016/j.jnoncrysol.2023.122322 · Cited by 97
Sol-Gel Synthesis of Non-Silica Monolithic Materials
(2010) · doi:10.3390/ma3042815 · Cited by 95
Mohanty, B., Bhanja, P., & Jena, B. K. (2022) · Materials Today Energy · doi:10.1016/j.mtener.2021.100902 · Cited by 88
Silica Aerogel: Synthesis, Characterization, Applications, and Recent Advancements
Rashid, A. B., Shishir, S. I., Mahfuz, M. A., Hossain, M. T., & Hoque, M. E. (2023) · Particle & Particle Systems Characterization · doi:10.1002/ppsc.202200186 · Cited by 86
Various methods for removal of dyes from industrial effluents - a review
Sharma, S., & Kaur, A. (2018) · Indian Journal of Science and Technology · doi:10.17485/ijst/2018/v11i12/120847 · Cited by 82
A comprehensive review of anionic azo dyes adsorption on surface-functionalised silicas
Al-Amrani, W. A., Hanafiah, M. A. K. M., & Mohammed, A.-H. A. (2022) · Environmental Science and Pollution Research · doi:10.1007/s11356-022-23062-0 · Cited by 79
Saiz, J., Bringas, E., & Ortiz, I. (2014) · Journal of Chemical Technology & Biotechnology · doi:10.1002/jctb.4331 · Cited by 79
Aerogels for Biomedical, Energy and Sensing Applications
Noman, M. T., Amor, N., Ali, A., Petrik, S., Coufal, R., Adach, K., & Fijalkowski, M. (2021) · Gels · doi:10.3390/gels7040264 · Cited by 73
A Comprehensive Review of Effective Adsorbents Used for the Removal of Dyes from Wastewater
Vishnu, D., Dhandapani, B., Authilingam, S., & Sivakumar, S. V. (2020) · Current Analytical Chemistry · doi:10.2174/1573411016999200831111155 · Cited by 66
Xu, C., Zhang, M., Yin, X., Gao, Q., Jiang, S., Cheng, J., Kong, X., Liu, B., & Peng, H.-Q. (2023) · Journal of Materials Chemistry A · doi:10.1039/d3ta02293e · Cited by 65
Hydrogen Production by Using Ru Nanoparticle Decorated with Fe3O4@SiO2–NH2 Core-Shell Microspheres
Sait Izgi, M., Ece, M. Ş., Kazici, H. Ç., Şahi̇n, Ö., & Onat, E. (2020) · International Journal of Hydrogen Energy · doi:10.1016/j.ijhydene.2020.08.043 · Cited by 64
Inocêncio, C. V. M., Holade, Y., Morais, C., Kokoh, K. B., & Napporn, T. W. (2023) · Electrochemical Science Advances · doi:10.1002/elsa.202100206 · Cited by 57
Study on Preparation and Performance of Advanced Aerogel Foamed Concrete with Ultra-Light Aerogel
Wu, H., Zhang, H., Zhang, G., Liu, J., Liu, Z., & Du, F. (2023) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2022.130166 · Cited by 53
Introduction to Electrocatalysts
Banoth, P., Kandula, C., & Kollu, P. (2022) · ACS symposium series · doi:10.1021/bk-2022-1432.ch001 · Cited by 51
Solanki, R., Patra, I., Ahmad, N., Kumar, N. B., Parra, R. M. R., Zaidi, M., Yasin, G., Anil Kumar, T. C., Hussein, H. A., Sivaraman, R., et al. (2022) · Journal of environmental chemical engineering · doi:10.1016/j.jece.2022.108207 · Cited by 49
Kayal, U., Mohanty, B., Bhanja, P., Chatterjee, S., Chandra, D., Hara, M., Kumar Jena, B., & Bhaumik, A. (2019) · Dalton Transactions · doi:10.1039/c8dt04159h · Cited by 48
The Synthesis and Polymer-Reinforced Mechanical Properties of SiO2 Aerogels: A Review
Zhan, W., Chen, L., Kong, Q., Li, L., Chen, M., Jiang, J., Li, W., Shi, F., & Xu, Z. (2023) · Molecules · doi:10.3390/molecules28145534 · Cited by 48
Sun, F., Xu, D., Xie, Y., Liu, F., Wang, W., Shao, H., Ma, Q., Yu, H., Yu, W., & Dong, X. (2022) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2022.08.089 · Cited by 47
Liu, Q., Liu, Y., Zhang, Z., Wang, X., & Shen, J. (2020) · Chinese Journal of Chemical Engineering · doi:10.1016/j.cjche.2020.04.023 · Cited by 39
A Review on Multifunctional Nanotechnological Aspects in Modern Textile
Sarvalkar, P. D., Barawkar, S. D., Karvekar, O. S., Patil, P. D., Prasad, S. R., Sharma, K. K., Prasad, N. R., & Vhatkar, R. S. (2023) · The Journal of The Textile Institute · doi:10.1080/00405000.2022.2046304 · Cited by 38 · cited 1×
“These clusters can be colloidal or polymeric in nature [29].”
Sarvalkar, P. D., Vadanagekar, A. S., Karvekar, O. S., Kumbhar, P. D., Terdale, S. S., Thounaojam, A. S., Kolekar, S. S., Vhatkar, R. S., Patil, P. S., & Sharma, K. K. K. (2023) · ACS Omega · doi:10.1021/acsomega.3c00552 · Cited by 37
Self-citationMajeed, S. S., Othuman Mydin, M. A., Bahrami, A., Dulaimi, A., Özkılıç, Y. O., Omar, R., & Jagadesh, P. (2024) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2024.01.282 · Cited by 37
Zhai, Q.-Z. (2020) · Water Science & Technology · doi:10.2166/wst.2020.267 · Cited by 35
Sharma, A. K., Sehgal, S. S., & Sandhu, H. (2018) · Indian Journal of Science and Technology · doi:10.17485/ijst/2018/v11i26/13056 · Cited by 35
Silica Foams with Ultra-Large Specific Surface Area Structured by Hollow Mesoporous Silica Spheres
Huo, W., Zhang, X., Hu, Z., Chen, Y., Wang, Y., & Yang, J. (2019) · Journal of the American Ceramic Society · doi:10.1111/jace.16115 · Cited by 34 · cited 1×
“From SEM, it was observed that the cell wall of the hollow sphere was 200–600 nm in range, showing apparent open pores [91].”
Premier, Progress and Prospects in Renewable Hydrogen Generation: A Review
Sharma, M., Pramanik, A., Bhowmick, G., Tripathi, A., Ghangrekar, M., Pandey, C., & Kim, B.-S. (2023) · Fermentation · doi:10.3390/fermentation9060537 · Cited by 34
Electrocatalysis: Fundamentals and Applications
Zinola, C. F., Martins, M. E., Tejera, E. P., & Neves, N. P. (2012) · International Journal of Electrochemistry · doi:10.1155/2012/874687 · Cited by 34 · cited 1×
“The primary variables that impact the characteristics of electrocatalyst atom rearrangements include the influence of surface roughness, identification of catalytic center sites, phase transitions, and on the catalytic surface that occur during electrochemical processes [62,63].”
Understanding Defect Chemistry in TMOS Involved Electrocatalytic OER; an Analysis for Advancement
Krishnan, A., Ajay, R., Anakha, J., & Namboothiri, U. S. K. (2022) · Surfaces and Interfaces · doi:10.1016/j.surfin.2022.101942 · Cited by 33
Yu, P.-J., Lee, M.-H., Hsu, H.-M., Tsai, H.-M., & Chen-Yang, Y. W. (2015) · RSC Advances · doi:10.1039/c4ra14002h · Cited by 32
Meléndez‐Ortiz, H. I., Puente‐Urbina, B., Mercado‐Silva, J. A., & García‐Uriostegui, L. (2019) · International Journal of Applied Ceramic Technology · doi:10.1111/ijac.13179 · Cited by 32
Flexible Hybrid and Single-Component Aerogels: Synthesis, Characterization, and Applications
Fijałkowski, M., Coufal, R., Ali, A., Adach, K., Petřík, S., Bu, H., & Karl, C. W. (2023) · Langmuir · doi:10.1021/acs.langmuir.3c01811 · Cited by 25
Huang, C., Cheng, X., Chen, B., Wang, J., Dai, Y., Situ, Y., & Huang, H. M. (2022) · Nano Letters · doi:10.1021/acs.nanolett.2c02768 · Cited by 20
Research Progress and Applications of Silica-Based Aerogels—A Bibliometric Analysis
Ji, C., Zhu, S., Zhang, E., Li, W., Liu, Y., Zhang, W., Su, C., Gu, Z., & Zhang, H. (2022) · RSC Advances · doi:10.1039/d2ra01511k · Cited by 20
Sharma, J., Sheikh, J., & Behera, B. K. (2023) · Drying Technology · doi:10.1080/07373937.2022.2162918 · Cited by 19
Effect of Catalyst and Substrate on the Moisture Diffusivity of Silica-Aerogel-Coated Metal Foams
Nawaz, K., Schmidt, S. J., & Jacobi, A. M. (2014) · International Journal of Heat and Mass Transfer · doi:10.1016/j.ijheatmasstransfer.2014.02.048 · Cited by 19 · cited 1×
“The mass diffusivity influences the adsorption rate, and the adsorption isotherm determines the capacity of a porous adsorbent material in the adsorption of an adsorbate gas [90].”
Effect of O 2 plasma treatment on the properties of SiO 2 aerogel film
Kim, H.-R., Park, H., Hyun, S., & Yeom, G. Y. (1998) · Thin Solid Films · doi:10.1016/s0040-6090(98)01044-x · Cited by 18
Plasma Treatments of Molecularly Templated Nanoporous Silica Films
Cho, A. T., Tsai, T. G., Yang, C., Chao, K. J., & Pan, F. (2001) · Electrochemical and Solid-State Letters · doi:10.1149/1.1354698 · Cited by 18
Aerogels-Inspired based Photo and Electrocatalyst for Water Splitting to Produce Hydrogen
Al-Hamamre, Z., Karimzadeh, Z., Ji, S., Choi, H., & Maleki, H. (2022) · Applied Materials Today · doi:10.1016/j.apmt.2022.101670 · Cited by 18
Synthesis of aerogel foams through a pressurized sol-gel method
Malakooti, S., Zhao, E., Tsao, N., et al. (2020) · Polymer · doi:10.1016/j.polymer.2020.122925 · Cited by 18
Kim, J.-J., Park, H.-H., & Hyun, S.-H. (2000) · Thin Solid Films · doi:10.1016/s0040-6090(00)01295-5 · Cited by 18
Vinayakumar, K., Palliyarayil, A., Kumar, N. S., & Sil, S. (2022) · Environmental Science and Pollution Research · doi:10.1007/s11356-022-20355-2 · Cited by 17
Yue, X., Li, H., Qiu, Y., Xiao, Z., Yu, X., Xue, C., & Xiang, J. (2021) · Journal of Solid State Chemistry · doi:10.1016/j.jssc.2021.122250 · Cited by 16
Engineering of Aerogel-Based Electrocatalysts for Oxygen Evolution Reaction
Gao, C., Zhang, X., Zhan, J., & Cai, B. (2022) · Electrochemical Science Advances · doi:10.1002/elsa.202100113 · Cited by 15
The Effect of Ar+ Ion Bombardment on SiO2 Aerogel Film
Kim, H.-R., & Park, H.-H. (1998) · Japanese Journal of Applied Physics · doi:10.1143/jjap.37.6955 · Cited by 14
Zhao, M., Wang, Y., Liu, Z., Cui, D., & Bian, X. (2011) · Journal of Macromolecular Science Part A · doi:10.1080/10601325.2011.573330 · Cited by 12
Joshi, M. M., Labhsetwar, N. K., Parwate, D. V., & Rayalu, S. S. (2013) · Materials Research Bulletin · doi:10.1016/j.materresbull.2013.05.057 · Cited by 9
Abebe, A. M., Sorarù, G. D., Ganesh, T., Andoshe, D. M., Zambotti, A., Ahmed, G. M. S., Tirth, V., & Algahtani, A. (2022) · Materials · doi:10.3390/ma15041277 · Cited by 8
Zhang, X., Shakeel, M., Li, B., & Wang, L. (2020) · Electrochimica Acta · doi:10.1016/j.electacta.2019.135369 · Cited by 6 · cited 1×
“In each instance, According to this, the presence of an acid or a base causes condensation. metaloxane or siloxane are formed in the bonds for different metals [7,45 In each instance, metaloxane or siloxane are formed in the bonds for di ff erent metals [7,45,47].”
Gowrisankar, A., & Kim, B. (2024) · Critical Reviews in Analytical Chemistry · doi:10.1080/10408347.2024.2358492 · Cited by 5
The role of vacuum ultraviolet in H2 plasma treatment on SiO2 aerogel film
Jung, S.-B., Park, H.-H., & Kim, H. (2003) · Applied Surface Science · doi:10.1016/s0169-4332(03)00508-7 · Cited by 4
Zhai, Q.-Z., & Dong, Y. (2019) · Instrumentation Science & Technology · doi:10.1080/10739149.2019.1597734 · Cited by 2
Jung, S.-B., & Park, H.-H. (2006) · Thin Solid Films · doi:10.1016/j.tsf.2005.08.082 · Cited by 2
Somakli, S., & Butun Sengel, S. (2023) · Silicon · doi:10.1007/s12633-023-02546-9 · Cited by 2
Research works printed but not linked: 3
- Faez, 2005, The State of Art and Possible New Applications of Nano/Meso Porous Silica Aerogel, Electron. J. Biol., 1, 76
- Brinker, C.J., and Scherer, G.W. (2013). Sol-Gel Science: The Physics and Chemistry of Sol-Gel Processing, Academic Press.
- Gores, H.J., and Schweiger, H. (2014). Encyclopedia of Applied Electrochemistry, Springer.
Cited by
Elavarasan, S., Begam, M. R., Balraj, B., Guo, D., & Bharathi, M. (2026) · Inorganic Chemistry Communications · doi:10.1016/j.inoche.2026.117560 · Cited by 2
Metadata
- Authors
- Vadanagekar, A., Lapcik, L., Kvitek, L., & Lapcikova, B.
- Affiliations
- Palacký University Olomouc (CZ)
- Department of Physical Chemistry, Faculty of Science, Palacky University in Olomouc, Listopadu 12, 771 46 Olomouc, Czech Republic
- Venue
- Molecules
- Publisher
- MDPI AG
- Published
- 2025-03-08
- Volume
- 30
- Issue
- 6
- Pages
- 1212
- ISSN
- 1420-3049 (ISSN-L)
- PMC
- PMC11944295
- OpenAlex
- W4408296865
- Semantic Scholar
- 3e51c9f8671d8335182338847b779d90c980b91b
- Cited by
- 4
- References
- 92
- Citations by year
- 2026: 3 · 2025: 1
- FWCI
- 0.35
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Molecules (publishedVersion, cc-by)
- PubMed Central (publishedVersion, cc-by)
- PubMed (publishedVersion)
- DOAJ (DOAJ: Directory of Open Access Journals) (submittedVersion, cc-by-sa)
- Funders
- Internal Student Grant Agency of the Palacký University in Olomouc, Czech Republic and Fischer Scholarship (ASV) (IGA_PrF_2025_022, NW25-08-00288)
- Czech Health Research Council (AZV), Ministry of Health of the Czech Republic (IGA_PrF_2025_022, NW25-08-00288)
- Topics
- Physical Sciences › Materials Science › Materials Chemistry › Aerogels and thermal insulation
- Physical Sciences › Materials Science › Materials Chemistry › Mesoporous Materials and Catalysis
- Physical Sciences › Energy › Renewable Energy, Sustainability and the Environment › Advanced Photocatalysis Techniques
- Keywords
- silica aerogel, water splitting, hydrogen production, environmental remediation, adsorbents, catalysts, dye degradation, aerogel synthesis, drying methods, water purification
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-11, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-11 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.