One part alkali activated materials: A state-of-the-art review
Open accessThe DOI matches its Crossref record; 217 of the 217 references it cites were found in a registry or an index.
Abstract
This article assesses the state-of-the-art for research on one-part alkali-activated materials, with particular emphasis on recent work dealing with the constituent materials, preparation methods, fresh properties, mechanical properties, and durability characteristics. The review, which covers over 170 studies, first discusses the different precursors, solid activators, admixtures, and aggregates used within such materials. Preparation techniques of one-part alkali-activated materials are then addressed, including pre-mixing treatment, mixing and curing, and 3D-printing. Reaction mechanisms and resulting binding phases are also outlined, followed by a detailed discussion on the fresh, mechanical and durability characteristics. The sensitivity of the compressive strength to different precursors and solid activators with varying chemical compositions, is examined, and predictive strength equations are proposed for common mixes. A brief comparison between the fresh, mechanical and durability characteristics of one-part and two-part AAMs is outlined, followed by a discussion on design standards as well as health and environmental aspects. The review concludes with suggestions for future research for key applications, with due consideration to the projected availability of precursors and the sustainability of solid activators. It is shown that despite the significant recent developments on one-part alkali-activated materials, further progress necessitates future research with a focus on optimising mixes made from precursors other than fly ash and blast furnace slag, as well as detailed investigations on structural members and components.
Overview
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Free: it reads the open-access text and checks the first 5 claims that cite a source we can check. Create a free account to check every claim.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Geopolymer technology: The current state of the art
Duxson, P., Fernández-Jiménez, A., Provis, J. L., Lukey, G. C., Palomo, A., & van Deventer, J. S. J. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0637-z · Cited by 4,742 · cited 1×
“The size of MK particles is usually less than 5 μ m [66], and their shape is plate-like and non-uniform [67].”
BackgroundProvis, J. L. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.02.009 · Cited by 2,272 · cited 5×
“It is formed via the chlor-alkali process which involves the electrolysis of a sodium chloride solution, and nearly 60 million tons of NaOH are produced annually following this method [73].”
BackgroundMethodInfluentialNew cements for the 21st century: The pursuit of an alternative to Portland cement
Shi, C., Jiménez, A. F., & Palomo, A. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.03.016 · Cited by 1,691
3D printing using concrete extrusion: A roadmap for research
Buswell, R. A., Leal de Silva, W. R., Jones, S. Z., & Dirrenberger, J. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.05.006 · Cited by 1,604
Geopolymers and Related Alkali-Activated Materials
Provis, J. L., & Bernal, S. A. (2014) · Annual Review of Materials Research · doi:10.1146/annurev-matsci-070813-113515 · Cited by 1,597 · cited 4×
“The chemical composition of GGBS mainly includes CaO, magnesium oxide (MgO), Al 2 O 3 and SiO 2 [19].”
BackgroundMethodInfluentialMechanism of geopolymerization and factors influencing its development: a review
Khale, D., & Chaudhary, R. (2007) · Journal of Materials Science · doi:10.1007/s10853-006-0401-4 · Cited by 1,463 · cited 1×
“Using low-calcium precursors leads to the formation of 3-dimensional tetrahedrally interlinked N-A-S-H (sodium-aluminum-silica-te-hydrate) gels [10,152], whereas high-calcium precursors result in the formation of tobermorite-like C-A-S-H (calcium-alumi-num-silicate-hydrate) gels [152 – 155].”
BackgroundOne-part alkali-activated materials: A review
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.10.001 · Cited by 1,456 · cited 1×
“It is white in colour and formed by adding aluminium hydroxide (Al(OH) 3 ) to a 20 – 25% aqueous NaOH solution [79].”
BackgroundSupplementary cementitious materials: New sources, characterization, and performance insights
Juenger, M. C. G., Snellings, R., & Bernal, S. A. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.05.008 · Cited by 1,260 · cited 2×
“Also, the wide use of FA as a supplementary cementitious material (SCM) in conventional concrete will inevitably create competitive demand pressure for its use [15].”
BackgroundMethodGeopolymers and other alkali activated materials: why, how, and what?
Provis, J. L. (2014) · Materials and Structures · doi:10.1617/s11527-013-0211-5 · Cited by 986 · cited 1×
“Increasing the Al content in the mix could help control efflorescence by ensuring a certain extent of reaction at an early stage [19,153].”
BackgroundClean production and properties of geopolymer concrete; A review
Amran, Y. H. M., Alyousef, R., Alabduljabbar, H., & El-Zeadani, M. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.119679 · Cited by 901 · cited 1×
“Conventional AAMs typically consist of an aluminosilicate precursor, also known as a starting material or source material, mixed with an alkaline solution [2].”
BackgroundSelf-citation3D printing trends in building and construction industry: a review
Tay, Y. W. D., Panda, B., Paul, S. C., Noor Mohamed, N. A., Tan, M. J., & Leong, K. F. (2017) · Virtual and Physical Prototyping · doi:10.1080/17452759.2017.1326724 · Cited by 868
Wolfs, R. J. M., Bos, F. P., & Salet, T. A. M. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.02.017 · Cited by 836 · cited 1×
“This was observed in several 3D-con-crete-printing studies [149,150] and is likely due to the higher porosity of printed materials in comparison to mould-cast specimens.”
BackgroundRecent progress in low-carbon binders
Shi, C., Qu, B., & Provis, J. L. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2019.05.009 · Cited by 714
Part, W. K., Ramli, M., & Cheah, C. B. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2014.12.065 · Cited by 525 · cited 1×
“Although adequate strengths were achieved using RHA as a lone precursor in one-part AAMs (7-day strengths ~30 MPa [54]), additional alumina sources are usually provided to ensure viable Si/Al ratios for long-term stability [58].”
BackgroundKim, M. S., Jun, Y., Lee, C., & Oh, J. E. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.09.011 · Cited by 518 · cited 3×
“These activators are considerably cheaper than Na 2 SiO 3 and NaOH (5 – 6 times cheaper) and easier to source [86].”
BackgroundA review on alkaline activation: New analytical perspectives
Palomo, A., Krivenko, P., Garcia-Lodeiro, I., Kavalerova, E., Maltseva, O., & Fernández-Jiménez, A. (2014) · Materiales de Construcción · doi:10.3989/mc.2014.00314 · Cited by 501 · cited 2×
“Blending low-calcium and high-calcium binders in one-part AAMs leads to the development of cross-linked N-A-S-H and C-A-S-H gels [10,139,156].”
BackgroundAlkali-Activated Cements and Concretes
Shi, C., Roy, D. M., & Krivenko, P. V. (2003) · CRC Press eBooks · doi:10.1201/9781482266900 · Cited by 491 · cited 2×
“Sodium carbonate can be produced from several chemical processes, including the Solvay process [20], and the annual production of Na 2 CO 3 stands at nearly 50 million tons [73].”
BackgroundAdvances in geopolymer materials: A comprehensive review
Cong, P., & Cheng, Y. (2021) · Journal of Traffic and Transportation Engineering (English Edition) · doi:10.1016/j.jtte.2021.03.004 · Cited by 481 · cited 1×
“MK was used extensively in one-part AAMs and results from the calcination of kaolinite clay at temperatures ranging from 450 to 800 ◦ C [10,55].”
MethodAlkali-activated slag cement and concrete: a review of properties and problems
Wang, S.-D., Pu, X.-C., Scrivener, K. L., & Pratt, P. L. (1995) · Advances in Cement Research · doi:10.1680/adcr.1995.7.27.93 · Cited by 474 · cited 3×
“Alkaline solutions employed in AAMs include alkali-hydroxides (i.e., M. Elzeadani et al. sodium/potassium hydroxides), non-silicic salts (sodium/potassium carbonates) or silicic salts (sodium/potassium silicates) [3].”
BackgroundMethodAbdalqader, A. F., Jin, F., & Al-Tabbaa, A. (2016) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2015.12.010 · Cited by 444 · cited 1×
“This activator can be obtained from natural sources, such as trona and Na 2 CO 3 -rich brines [73], with reserves of over 24 billion tons worldwide [77].”
BackgroundBinding mechanism and properties of alkali-activated fly ash/slag mortars
Chi, M., & Huang, R. (2013) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2012.11.003 · Cited by 428 · cited 1×
“For instance, GGBS-based mixtures tend to have a more compact pore structure when compared to sole FA-based mixes [190], binary GGBS-and FASB-based pastes [12,167] or binary LS-and GGBS-based systems [23] due to the nature of hydration products formed.”
BackgroundNematollahi, B., Sanjayan, J., & Shaikh, F. U. A. (2015) · Ceramics International · doi:10.1016/j.ceramint.2014.12.154 · Cited by 426 · cited 4×
“…( M s = SiO 2 /Na 2 O) of around 0.9 typically outperforms the others, including Na 2 SiO 3 ⋅ 5H 2 O ( M s ≈ 1.04), Na 2 SiO 3 ⋅ 9H 2 O ( M s ≈ 1.03), Na 2 SiO 3 -GD ( M s = 2.0), quick-dissolving Na 2 SiO 3 ( M s ≈ 2.86) and sodium disilicate (Na 2 Si 2 O 5 ) ( M s ≈ 1.98) [4,5,27,84,170].”
BackgroundMethodInfluentialSynthesis and strength optimization of one-part geopolymer based on red mud
Ye, N., Yang, J., Liang, S., Hu, Y., Hu, J., Xiao, B., & Huang, Q. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.02.099 · Cited by 363 · cited 2×
“Silica fume (SF) – also known as microsilica or silica dust – is a by-product of the smelting process in silicon and ferrosilicon alloy production [33,34].”
BackgroundYousefi Oderji, S., Chen, B., Ahmad, M. R., & Shah, S. F. A. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.03.290 · Cited by 360 · cited 4×
“A Comparative study on FA-and GGBS-based one-part AA pastes activated using NaOH, KOH and Na 2 SiO 3 -anhydrous showed that NaOH activated mixes achieved the lowest flowability and higher rate of flow loss [161].”
BackgroundInfluentialProperties of cementless mortars activated by sodium silicate
Yang, K.-H., Song, J.-K., Ashour, A. F., & Lee, E.-T. (2008) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2007.07.003 · Cited by 319 · cited 3×
“For instance, Yang et al. [135] reported that the 28-day compressive strength of GGBS-based AA mortars (21.5 – 52.5 MPa) was higher than that of FA-based counterparts (0.57 – 9.45 MPa) using the same solid activator and cured in the same environment.”
BackgroundMethodInfluentialEffect of Alumina Release Rate on the Mechanism of Geopolymer Gel Formation
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2010) · Chemistry of Materials · doi:10.1021/cm101151n · Cited by 314 · cited 1×
“Besides SF, geothermal silica (GS) was used as a supplementary SiO 2 source in one-part AAMs [36,37].”
MethodOne‐Part Geopolymers Based on Thermally Treated Red Mud/NaOH Blends
Ke, X., Bernal, S. A., Ye, N., Provis, J. L., & Yang, J. (2015) · Journal of the American Ceramic Society · doi:10.1111/jace.13231 · Cited by 283 · cited 1×
“Ke et al. [131] and Ye et al. [33] performed alkali-fusion to enhance the reactivity of RM by heating it with NaOH at 800 ◦ C for 1 h.”
BackgroundThe effect of silica availability on the mechanism of geopolymerisation
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2011) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.02.001 · Cited by 279 · cited 1×
“Due to its high alumina content, NaAlO 2 was mainly combined with high silica precursors, such as RHA [54], SF [38,80], SR [81], and GS [37,82], or as substitutes to a proportion of Na 2 SiO 3 in FA-and GGBS-based mixes [13,83].”
MethodMicrostructure of ultra high performance concrete containing lithium slag
He, Z.-H., Du, S.-G., & Chen, D. (2018) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2018.03.063 · Cited by 279 · cited 1×
“It is a waste residue from lithium carbonate (Li 2 CO 3 ) production, and estimates suggest that about 10 tons of LS are generated for each ton of Li 2 CO 3 produced [25].”
BackgroundVinai, R., & Soutsos, M. (2019) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.11.008 · Cited by 279 · cited 1×
“Commercial Na 2 SiO 3 powder is white and spherical, and is produced by heating sodium carbonate (Na 2 CO 3 ) and SiO 2 at temperatures as high as 1200 ◦ C [74].”
BackgroundThe role of particle technology in developing sustainable construction materials
Provis, J. L., Duxson, P., & van Deventer, J. S. J. (2010) · Advanced Powder Technology · doi:10.1016/j.apt.2009.10.006 · Cited by 278 · cited 2×
“Rapid shearing of the fresh mix should be continued by the mixing machine without the addition of extra water to avoid reductions in mechanical properties and any harmful effects on durability [137].”
BackgroundMethodProperties and characterization of green one-part geopolymer activated by composite activators
Ma, C., Zhao, B., Guo, S., Long, G., & Xie, Y. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.02.159 · Cited by 273 · cited 7×
“For instance, GGBS-based mixtures tend to have a more compact pore structure when compared to sole FA-based mixes [190], binary GGBS-and FASB-based pastes [12,167] or binary LS-and GGBS-based systems [23] due to the nature of hydration products formed.”
BackgroundMethodInfluentialComparison of alkali and silica sources in one-part alkali-activated blast furnace slag mortar
Luukkonen, T., Abdollahnejad, Z., Yliniemi, J., Kinnunen, P., & Illikainen, M. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.03.202 · Cited by 261 · cited 4×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
BackgroundInfluentialSynthesis and characterization of one-part geopolymers for extrusion based 3D concrete printing
Panda, B., Singh, G. B., Unluer, C., & Tan, M. J. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.02.185 · Cited by 254 · cited 5×
“The mechanical properties of the resulting 3D-printed one-part AAM depend on several print related parameters, such as printing layer height and printing speed [92].”
BackgroundMethodInfluentialMa, C., Long, G., Shi, Y., & Xie, Y. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.08.060 · Cited by 253 · cited 3×
“In one-part AAMs, several forms of granular Na 2 SiO 3 were used with different amounts of chemically bound water, including sodium metasilicate anhydrous (Na 2 SiO 3 -anhydrous), sodium metasilicate pentahydrate (Na 2 SiO 3 ⋅ 5H 2 O), and sodium metasilicate nonahydrate (Na 2 SiO 3 ⋅ 9H 2 O) [76].”
BackgroundMethodInfluentialAn overview of the chemistry of alkali-activated cement-based binders
Garcia-Lodeiro, I., Palomo, A., & Fernández-Jiménez, A. (2015) · Handbook of Alkali-Activated Cements, Mortars and Concretes · doi:10.1533/9781782422884.1.19 · Cited by 249 · cited 4×
“Using low-calcium precursors leads to the formation of 3-dimensional tetrahedrally interlinked N-A-S-H (sodium-aluminum-silica-te-hydrate) gels [10,152], whereas high-calcium precursors result in the formation of tobermorite-like C-A-S-H (calcium-alumi-num-silicate-hydrate) gels [152 – 155].”
BackgroundMethodInfluentialCharacteristics and properties of lightweight concrete manufactured with cenospheres
Blanco, F., Garcı́a, P., Mateos, P., & Ayala, J. (2000) · Cement and Concrete Research · doi:10.1016/s0008-8846(00)00357-4 · Cited by 248 · cited 1×
“This by-product is characteristically lightweight with spherical and hollow particles [17,18].”
BackgroundThermal Activation of Albite for the Synthesis of One‐Part Mix Geopolymers
Feng, D., Provis, J. L., & van Deventer, J. S. J. (2012) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2011.04925.x · Cited by 244 · cited 4×
“For example, Feng et al. [68] heated albite powder with NaOH/Na 2 CO 3 at temperatures ranging from 850 ◦ C to 1150 ◦ C for a period of 30 min.”
BackgroundInfluentialRavikumar, D., & Neithalath, N. (2012) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2012.03.006 · Cited by 244
One-Part Geopolymer Mixes from Geothermal Silica and Sodium Aluminate
Hajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2008) · Industrial & Engineering Chemistry Research · doi:10.1021/ie8006825 · Cited by 239 · cited 1×
“SEM images of aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48]…”
BackgroundGeopolymerisation kinetics. 1. In situ energy-dispersive X-ray diffractometry
Provis, J. L., & van Deventer, J. S. J. (2007) · Chemical Engineering Science · doi:10.1016/j.ces.2007.01.027 · Cited by 224 · cited 1×
“The solubility of sodium silicate powders was determined to be less than that of potassium silicate powders, mainly due to the smaller hydration sphere of potassium ions [91,157,158].”
BackgroundCong, P., & Mei, L. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.122171 · Cited by 224 · cited 1×
“The potential of calcium carbide residue (CCR) as a solid activator in FA and GGBS-based AAMs was also investigated in several studies [102 – 105].”
BackgroundNematollahi, B., Sanjayan, J., Qiu, J., & Yang, E.-H. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.11.117 · Cited by 223
Properties and sustainability of alkali-activated slag foamed concrete
Yang, K.-H., Lee, K.-H., Song, J.-K., & Gong, M.-H. (2014) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2013.12.068 · Cited by 213
Alrefaei, Y., & Dai, J.-G. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.07.012 · Cited by 213
Tensile Strain Hardening Behavior of PVA Fiber-Reinforced Engineered Geopolymer Composite
Nematollahi, B., Sanjayan, J., & Ahmed Shaikh, F. U. (2015) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0001242 · Cited by 205
One-part geopolymer cement from slag and pretreated paper sludge
Adesanya, E., Ohenoja, K., Luukkonen, T., Kinnunen, P., & Illikainen, M. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.03.007 · Cited by 202
Synthesizing one-part geopolymers from rice husk ash
Sturm, P., Gluth, G. J. G., Brouwers, H. J. H., & Kühne, H.-C. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.017 · Cited by 200 · cited 3×
“This high SiO 2 ( > 85%-weight) waste product is the result of burning rice husk generated from rice paddies at a temperature of around 600 – 800 ◦ C [54 – 56].”
BackgroundMethodHanif, A., Diao, S., Lu, Z., Fan, T., & Li, Z. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.04.134 · Cited by 197 · cited 1×
“This by-product is characteristically lightweight with spherical and hollow particles [17,18].”
BackgroundCo-disposal of MSWI fly ash and Bayer red mud using an one-part geopolymeric system
Ye, N., Chen, Y., Yang, J., Liang, S., Hu, Y., Xiao, B., Huang, Q., Shi, Y., Hu, J., & Wu, X. (2016) · Journal of Hazardous Materials · doi:10.1016/j.jhazmat.2016.06.042 · Cited by 194 · cited 2×
“The annual global production of RM is about 120 million tons [40,41], and its high alkalinity (pH in the range of 10 – 12.5), together with its chemical composition ( > 80% of SiO 2 + Fe 2 O 3 + Al 2 O 3 + Na 2 O + CaO), makes it suitable as both precursor and activator.”
BackgroundMethodInfluentialAmbient temperature cured ‘just-add-water’ geopolymer for 3D concrete printing applications
Bong, S. H., Xia, M., Nematollahi, B., & Shi, C. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104060 · Cited by 193 · cited 1×
“Bong et al. [147] reported that the 28-day compressive strength of 3D-printed FA-and GGBS-based one-part AAMs was 10 – 27% lower than that of normal mould-cast specimens.”
BackgroundCharacterisation of One-Part Geopolymer Binders Made from Fly Ash
Hajimohammadi, A., & van Deventer, J. S. J. (2017) · Waste and Biomass Valorization · doi:10.1007/s12649-016-9582-5 · Cited by 192 · cited 1×
“Similarly, Hajimohammadi and van Deventer [160] highlighted that certain zeolite phases observed in FA-based two-part AAMs did not appear in FA-based one-part AAMs.”
BackgroundPanda, B., Ruan, S., Unluer, C., & Tan, M. J. (2020) · Composites Part B Engineering · doi:10.1016/j.compositesb.2020.107826 · Cited by 192 · cited 3×
“In a recent study, the rheological behaviour of 3D-printed GGBS-based one-part AAMs was investigated [145].”
BackgroundInfluentialThe effectiveness of different superplasticizers in ambient cured one-part alkali activated pastes
Alrefaei, Y., Wang, Y.-S., & Dai, J.-G. (2019) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2018.12.027 · Cited by 190 · cited 1×
“Alrefaei et al. [123] stated that for FA-and GGBS-based mixes, the water-to-binder (w/b) ratio was critical, with polycarboxylate-based SPs giving better results at a w/b ratio greater than 0.36 .”
MethodInfluentialTorres‐Carrasco, M., & Puertas, F. (2017) · Revista de ingeniería de construcción · doi:10.4067/s0718-50732017000200001 · Cited by 188 · cited 1×
“Using low-calcium precursors leads to the formation of 3-dimensional tetrahedrally interlinked N-A-S-H (sodium-aluminum-silica-te-hydrate) gels [10,152], whereas high-calcium precursors result in the formation of tobermorite-like C-A-S-H (calcium-alumi-num-silicate-hydrate) gels [152 – 155].”
BackgroundNematollahi, B., Sanjayan, J., Qiu, J., & Yang, E.-H. (2017) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2016.12.005 · Cited by 187
Development of high strength one-part geopolymer mortar using sodium metasilicate
Dong, M., Elchalakani, M., & Karrech, A. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.117611 · Cited by 187 · cited 9×
“Having finer Na 2 SiO 3 ⋅ 5H 2 O particles was shown to result in higher compressive strength in FA-and GGBS-based mixes [163].”
BackgroundMethodInfluentialMix composition and characterisation of one-part geopolymers with different activators
Askarian, M., Tao, Z., Samali, B., Adam, G., & Shuaibu, R. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.07.083 · Cited by 182 · cited 3×
“Adding potassium carbonate (K 2 CO 3 ) to Na 2 SiO 3 -GD and Ca(OH) 2 in FA-based one-part mixes caused a further reduction in workability [168].”
BackgroundInfluentialPore characteristics in one-part mix geopolymers foamed by H 2 O 2 : The impact of mix design
Hajimohammadi, A., Ngo, T., Mendis, P., Nguyen, T., Kashani, A., & van Deventer, J. S. J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.05.084 · Cited by 181 · cited 1×
“Aluminum powder, hydrogen peroxide (H 2 O 2 ), and surfactant were used as admixtures to form foamed one-part AAMs [97,128].”
MethodImprovement of early strength of fly ash-slag based one-part alkali activated mortar
Shah, S. F. A., Chen, B., Oderji, S. Y., Haque, M. A., & Ahmad, M. R. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118533 · Cited by 180 · cited 2×
“Few studies reported that adding sodium tetraborate decahydrate-borax to FA-and GGBS-based one-part AAMs (dosages in the range of 2 – 8% of precursor content) caused a reduction in strength in proportion with the dosage added [124,165].”
BackgroundCompressive strength of one-part alkali activated fly ash using red mud as alkali supplier
Choo, H., Lim, S., Lee, W., & Lee, C. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.08.015 · Cited by 178 · cited 3×
“SEM images of aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48]…”
BackgroundOderji, S. Y., Chen, B., Shakya, C., Ahmad, M. R., & Shah, S. F. A. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.116891 · Cited by 178 · cited 3×
“SEM images of aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48]…”
BackgroundMethodInfluentialA novel method to produce dry geopolymer cement powder
Abdel-Gawwad, H. A., & Abo-El-Enein, S. A. (2016) · HBRC Journal · doi:10.1016/j.hbrcj.2014.06.008 · Cited by 176 · cited 2×
“For instance, the water absorption of GGBS-based one-part pastes activated using a combination of NaOH and CaCO 3 decreased as the w/s ratio increased from 0.24 to 0.27 and then increased again with a further increase in w/s up to 0.33 [180].”
BackgroundInfluential3D printing geopolymers: A review
Zhong, H., & Zhang, M. (2022) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2022.104455 · Cited by 176 · cited 3×
“In recent years, 3D printing technology/digital construction has gained increased interest, particularly due to the expected savings in construction time, material and labour with such technology and the potential for increased geometrical freedom [140 – 142].”
BackgroundMethodPreparation, structure and hydrothermal stability of alternative (sodium silicate-free) geopolymers
Koloušek, D., Brus, J., Urbanova, M., Andertova, J., Hulinsky, V., & Vorel, J. (2007) · Journal of Materials Science · doi:10.1007/s10853-007-1910-5 · Cited by 175
Valorization of waste powders from cement-concrete life cycle: A pathway to circular future
Kaliyavaradhan, S. K., Ling, T., & Mo, K. H. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.122358 · Cited by 174
Manufacture of hybrid cements with fly ash and bottom ash from a municipal solid waste incinerator
García-Lodeiro, I., Taboada, V. C., Fernández‐Jiménez, A., & Palomo, A. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.12.079 · Cited by 174 · cited 2×
“Both MSWI FA and MSWI BA show high concentrations of CaO and their XRD patterns depict peaks of quartz and calcite; and calcite, portlandite, halite and periclase, respectively [56,64].”
BackgroundMethodNeupane, K. (2016) · Mechanics of Materials · doi:10.1016/j.mechmat.2016.09.012 · Cited by 174 · cited 2×
“Both Neupane [188] and Neupane et al. [189] suggest Eq.”
BackgroundInfluentialMellado, A., Catalán, C., Bouzón, N., Borrachero, M. V., Monzó, J. M., & Payá, J. (2014) · RSC Adv. · doi:10.1039/c4ra03375b · Cited by 172 · cited 2×
“The production of NaOH is energy intensive and nearly 1.1 kg of CO 2 is emitted for each 1 kg of NaOH produced [75].”
BackgroundInfluentialAdesanya, E., Perumal, P., Luukkonen, T., Yliniemi, J., Ohenoja, K., Kinnunen, P., & Illikainen, M. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.125558 · Cited by 170 · cited 2×
“Among such activators is paper sludge (PS), a waste material rich in CaO resulting from the treatment of recycled paper [35,94].”
BackgroundDevelopment of Cleaner One-part geopolymer from lithium slag
Ali Shah, S. F., Chen, B., Ahmad, M. R., & Haque, M. A. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.125241 · Cited by 168 · cited 7×
“SEM images of aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48]…”
BackgroundMethodInfluentialFormation of one-part-mixing geopolymers and geopolymer ceramics from geopolymer powder
Liew, Y.-M., Cheng-Yong, H., Li, L.-Y., Jaya, N. A., Abdullah, M. M. A. B., Tan, S. J., & Kamarudin, H. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.08.110 · Cited by 165 · cited 1×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
Sulfuric acid resistance of one-part alkali-activated mortars
Sturm, P., Gluth, G. J. G., Jäger, C., Brouwers, H. J. H., & Kühne, H.-C. (2018) · Cement and Concrete Research · doi:10.1016/j.cemconres.2018.04.009 · Cited by 163 · cited 2×
“Higher calcium content in the precursor causes the formation of expansive products, such as gypsum and ettringite, when in contract with aggressive solutions, which could further damage the microstructure of one-part AAMs [81].”
BackgroundMethodHassan, H. S., Abdel-Gawwad, H. A., Vásquez-García, S. R., Israde-Alcántara, I., Flores-Ramirez, N., Rico, J. L., & Mohammed, M. S. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.11.137 · Cited by 162 · cited 1×
“Olive stone biomass ash (OBA), almond-shell biomass ash (ABA), and wood biomass ash (WBA), with their high K 2 O and CaO contents, were also used as solid activators [97 – 99].”
MethodMechanical properties of ambient cured one-part hybrid OPC-geopolymer concrete
Askarian, M., Tao, Z., Adam, G. A., & Samali, B. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.07.160 · Cited by 162 · cited 1×
“Several types of coarse aggregates were used in one-part AAC, including granite [90], basalt [108], limestone [109], dolomite [110], clay granules [111], and IMT waste [103].”
MethodMohammed, B. S., Haruna, S., Wahab, M. M. A., Liew, M. S., & Haruna, A. (2019) · Heliyon · doi:10.1016/j.heliyon.2019.e02255 · Cited by 160
Transformations of Na, Al, Si and Fe species in red mud during synthesis of one-part geopolymers
Ye, N., Chen, Y., Yang, J., Liang, S., Hu, Y. Q., Hu, J., Zhu, S., Fan, W., & Xiao, B. (2017) · Cement and Concrete Research · doi:10.1016/j.cemconres.2017.08.027 · Cited by 159 · cited 3×
“The annual global production of RM is about 120 million tons [40,41], and its high alkalinity (pH in the range of 10 – 12.5), together with its chemical composition ( > 80% of SiO 2 + Fe 2 O 3 + Al 2 O 3 + Na 2 O + CaO), makes it suitable as both precursor and activator.”
BackgroundInfluentialEnvironmental and economic perspective of waste-derived activators on alkali-activated mortars
Abdulkareem, M., Havukainen, J., Nuortila-Jokinen, J., & Horttanainen, M. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.124651 · Cited by 159 · cited 1×
“These include some of the precursors addressed earlier such as RM [41,42], CoW [61], VT [49,50], and WG [95].”
BackgroundMechanical properties and reaction mechanism of one-part geopolymer mortars
Zhang, H., Liu, J., & Wu, B. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.121973 · Cited by 159 · cited 10×
“…profiles of FA-and MK-based one-part AAMs activated with a combination of hydrous Na 2 SiO 3 and NaOH or Na 2 SiO 3 - anhydrous showed higher reaction heat with an increase in the activator intensity or a reduction in the activator modulus (i.e., higher reaction heat with higher alkalinity) [5].”
BackgroundInfluentialGlass waste versus sand as aggregates: The characteristics of the evolving geopolymer binders
Hajimohammadi, A., Ngo, T., & Kashani, A. (2018) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2018.05.086 · Cited by 159 · cited 2×
“The sources of natural aggregate replacements include crushed bricks [112], WG [113,114], CW [62,115], waste sands [107], crumb rubber [116], and sand derived from IMT waste [103].”
BackgroundYang, K.-H., & Song, J.-K. (2009) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)0899-1561(2009)21:3(119 · Cited by 157 · cited 4×
“The fineness of the source material plays an important role in the resulting compressive strength, with finer precursors often resulting in improved compressive strength development [110,136].”
BackgroundMethodInfluentialRetention of alkali ions by hydrated low-pH cements: Mechanism and Na+/K+ selectivity
Bach, T. T. H., Chabas, E., Pochard, I., Coumes, C. C. D., Haas, J., Frizon, F., & Nonat, A. (2013) · Cement and Concrete Research · doi:10.1016/j.cemconres.2013.04.010 · Cited by 155 · cited 1×
“The solubility of sodium silicate powders was determined to be less than that of potassium silicate powders, mainly due to the smaller hydration sphere of potassium ions [91,157,158].”
BackgroundLuukkοnen, T., Sreenivasan, H., Abdollahnejad, Z., Yliniemi, J., Kantola, A. M., Telkki, V., Kinnunen, P., & Illikainen, M. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.117354 · Cited by 155
High-Strength Geopolymer Concrete- Properties, Advantages and Challenges
Neupane, K. (2018) · Advances in Materials · doi:10.11648/j.am.20180702.11 · Cited by 155 · cited 2×
“Both Neupane [188] and Neupane et al. [189] suggest Eq.”
BackgroundInfluentialGuo, W., Zhang, Z., Bai, Y., Zhao, G., Sang, Z., & Zhao, Q. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.123367 · Cited by 154 · cited 1×
“Replacing a proportion of soda residue with CCR to activate GGBS-based AA mortars led to lower drying shrinkage values [104].”
BackgroundSustainable one-part geopolymer foams with glass fines versus sand as aggregates
Hajimohammadi, A., Ngo, T., & Kashani, A. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.03.120 · Cited by 149 · cited 3×
“Meanwhile, replacing a proportion of sand particles with either CW or WG fine aggregates in FA-and GGBS-based one-part AAMs resulted in an increase in the compressive strength [113,115,184].”
BackgroundMethodSamarakoon, M. H., Ranjith, P. G., Duan, W., & Silva, V. R. S. D. (2020) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103679 · Cited by 149 · cited 1×
“Comparing the compressive strength of two-part AAMs to that of similar one-part systems, the former usually develops a relatively higher compressive strength [193,194].”
BackgroundMine wastes based geopolymers: A critical review
Mabroum, S., Moukannaa, S., Machi, A. E., Taha, Y., Benzaazoua, M., & Hakkou, R. (2020) · Cleaner Engineering and Technology · doi:10.1016/j.clet.2020.100014 · Cited by 143 · cited 1×
“GMTs – a waste material from mining gold – mainly consist of SiO 2 and Al 2 O 3 , and their mineral phase structure is highly crystalline with peaks including quartz, albite, microcline, and muscovite [51].”
BackgroundInfluence of activator composition on the chloride binding capacity of alkali-activated slag
Ye, H., Huang, L., & Chen, Z. (2019) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2019.103368 · Cited by 142 · cited 1×
“However, Na 2 SO 4 possesses low pH ( 8) and results in mixes with a relatively lower strength [84,85].”
BackgroundHajimohammadi, A., Provis, J. L., & van Deventer, J. S. J. (2011) · Journal of Colloid and Interface Science · doi:10.1016/j.jcis.2011.02.045 · Cited by 140 · cited 2×
“Besides SF, geothermal silica (GS) was used as a supplementary SiO 2 source in one-part AAMs [36,37].”
MethodShah, S. F. A., Chen, B., Oderji, S. Y., Haque, M. A., & Ahmad, M. R. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118221 · Cited by 140
Ma, C., Zhao, B., Wang, L., Long, G., & Xie, Y. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.119279 · Cited by 139 · cited 7×
“Using Na 2 SiO 3 -anhydrous as a sole activator in GGBS-and FASB-based mixes resulted in lower porosity than using it in combination with either Na 2 CO 3 or Na 2 SO 4 [12,84,167].”
BackgroundMethodInfluentialMechanochemical synthesis of one-part alkali aluminosilicate hydraulic cement
Matalkah, F., Xu, L., Wu, W., & Soroushian, P. (2016) · Materials and Structures · doi:10.1617/s11527-016-0968-4 · Cited by 137 · cited 5×
“SEM images of aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48]…”
BackgroundMethodInfluentialAbdollahnejad, Z., Mastali, M., Woof, B., & Illikainen, M. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118129 · Cited by 137 · cited 4×
“The sources of natural aggregate replacements include crushed bricks [112], WG [113,114], CW [62,115], waste sands [107], crumb rubber [116], and sand derived from IMT waste [103].”
BackgroundMethodInfluentialAlmalkawi, A. T., Balchandra, A., & Soroushian, P. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.06.054 · Cited by 130 · cited 4×
“Both MSWI FA and MSWI BA show high concentrations of CaO and their XRD patterns depict peaks of quartz and calcite; and calcite, portlandite, halite and periclase, respectively [56,64].”
BackgroundMethodInfluentialExperimental comparisons between one-part and normal (two-part) alkali-activated slag binders
Ren, J., Sun, H., Li, Q., Li, Z., Ling, L., Zhang, X., Wang, Y., & Xing, F. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.125177 · Cited by 126 · cited 9×
“Saedi et al. [175] and Ren et al. [151] showed more rapid setting in GGBS-based two-part AAMs when compared to their one-part counterparts.”
BackgroundMethodResultInfluentialMohammed, B. S., Haruna, S., Wahab, M. M. A., & Liew, M. S. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.07.267 · Cited by 122
Lemougna, P. N., Adediran, A. A., Yliniemi, J., Ismailov, A., Levänen, E., Tanskanen, P., Kinnunen, P., Röning, J., & Illikainen, M. (2020) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103792 · Cited by 121 · cited 2×
“Lemougna et al. [177] also re-ported lower 7-day compressive strength of MK-based one-part pastes (~20 MPa) activated with Na 2 SiO 3 -anhydrous in comparison to GGBS-based one-part AA pastes (~62 MPa).”
BackgroundMethodDevelopment of artificial one-part geopolymer lightweight aggregates by crushing technique
Xu, L.-Y., Qian, L.-P., Huang, B.-T., & Dai, J. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.128200 · Cited by 120 · cited 2×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
MethodDevelopment and Characterization of Fly Ash–Slag Blended Geopolymer Mortar and Lightweight Concrete
Ismail, N., & El-Hassan, H. (2018) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0002209 · Cited by 120 · cited 1×
“Moreover, the flow loss of GGBS-based mixes with time is considerably higher than their FA-based counterparts [162].”
BackgroundDrying shrinkage of alkali activated binders cured at room temperature
Matalkah, F., Salem, T., Shaafaey, M., & Soroushian, P. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.12.223 · Cited by 119 · cited 4×
“Meanwhile, the addition of 5 wt% SF to a ternary blend of FA, GGBS and albite-based one-part AAM led to a slight increase in the drying shrinkage [127].”
BackgroundInfluentialPeng, M. X., Wang, Z. H., Shen, S. H., & Xiao, Q. G. (2014) · Materials and Structures · doi:10.1617/s11527-014-0350-3 · Cited by 118
Drying shrinkage of one-part alkali-activated slag concrete
Sadeghian, G., Behfarnia, K., & Teymouri, M. (2022) · Journal of Building Engineering · doi:10.1016/j.jobe.2022.104263 · Cited by 117 · cited 6×
“The addition of SF by 15% of binder weight to GGBS-based one-part AAC led to a significant reduction in the drying shrinkage by as much as 32% [109].”
BackgroundMethodInfluentialEffect of superplasticizers on properties of one-part Ca(OH)2/Na2SO4 activated geopolymer pastes
Alrefaei, Y., Wang, Y., Dai, J.-G., & Xu, Q. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.117990 · Cited by 116
Liu, Q., Li, X., Cui, M., Wang, J., & Lyu, X. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.126806 · Cited by 115 · cited 3×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
BackgroundAlternative alkali-activator from steel-making waste for one-part alkali-activated slag
Adesanya, E., Ohenoja, K., Maria, A. D., Kinnunen, P., & Illikainen, M. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.123020 · Cited by 114 · cited 1×
“Desulphurization dust, a waste product from steel production, with its high Na 2 O and CaO contents was also used as an activator in GGBS-based one-part AAMs [106].”
MethodSuwan, T., & Fan, M. (2016) · Materials and Manufacturing Processes · doi:10.1080/10426914.2016.1198013 · Cited by 110 · cited 1×
“Comparing the compressive strength of two-part AAMs to that of similar one-part systems, the former usually develops a relatively higher compressive strength [193,194].”
BackgroundGuo, W., Wang, S., Xu, Z., Zhang, Z., Zhang, C., Bai, Y., & Zhao, Q. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.124403 · Cited by 110 · cited 2×
“The potential of calcium carbide residue (CCR) as a solid activator in FA and GGBS-based AAMs was also investigated in several studies [102 – 105].”
BackgroundMethodPotassium-rich biomass ashes as activators in metakaolin-based inorganic polymers
Peys, A., Rahier, H., & Pontikes, Y. (2015) · Applied Clay Science · doi:10.1016/j.clay.2015.11.003 · Cited by 107 · cited 3×
“For instance, Maize stalk ash (MSA) and maize cob ash (MCA) from burning maize stalk and cob, respectively, were utilized as solid activators [28,96].”
BackgroundMethodInfluentialKadhim, A., Sadique, M., Al-Mufti, R. L., & Hashim, K. (2020) · Journal of Building Engineering · doi:10.1016/j.jobe.2020.101766 · Cited by 107 · cited 9×
“For example, Kadhim et al. [67,71] showed that calcining LKD at 950 ◦ C to activate MK-based one-part AAMs helped enhance the compressive strength remarkably.”
BackgroundMethodInfluentialThe degradation mechanisms of alkali-activated fly ash/slag blend cements exposed to sulphuric acid
Zhang, W., Yao, X., Yang, T., & Zhang, Z. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.08.050 · Cited by 106 · cited 1×
“Resistance of one-part AAMs to aggressive solutions depends mainly on their porosity as well as the nature of their hydration products [191].”
BackgroundSuitability of commercial superplasticizers for one-part alkali-activated blast-furnace slag mortar
Luukkοnen, T., Abdollahnejad, Z., Ohenoja, K., Kinnunen, P., & Illikainen, M. (2019) · Journal of Sustainable Cement-Based Materials · doi:10.1080/21650373.2019.1625827 · Cited by 105 · cited 1×
“…waste products: ABA [98] , WBA [118] , MCA [211] , MSA [212] , PS [94] , LKD [67]. the range of 0.5 – 1.0% gave better fresh properties in comparison to other SPs, such as sulfonated melamine-formaldehyde, sulfonated naphthalene-formaldehyde, polycarboxylate and carboxylic acrylic ester [110,122].”
BackgroundInfluentialPeng, M. X., Wang, Z. H., Shen, S. H., Xiao, Q. G., Li, L. J., Tang, Y. C., & Hu, L. L. (2016) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2016.11.010 · Cited by 104
Durability of the Reinforced One-Part Alkali-Activated Slag Mortars with Different Fibers
Abdollahnejad, Z., Mastali, M., Falah, M., Shaad, K. M., Luukkοnen, T., & Illikainen, M. (2020) · Waste and Biomass Valorization · doi:10.1007/s12649-020-00958-x · Cited by 104
Fiber-reinforced one-part alkali-activated slag/ceramic binders
Abdollahnejad, Z., Mastali, M., Luukkοnen, T., Kinnunen, P., & Illikainen, M. (2018) · Ceramics International · doi:10.1016/j.ceramint.2018.02.097 · Cited by 104 · cited 1×
“Abdollahnejad et al. [186] noted that water curing had a greater impact on improving the compressive strength of GGBS-and CW-based one-part mortars activated via Na 2 SiO 3 -anhydrous than sealed curing.”
Background3D-printable alkali-activated concretes for building applications: A critical review
Amran, M., Abdelgader, H. S., Onaizi, A. M., Федюк, Р. С., Ozbakkaloglu, T., Rashid, R. S. M., & Murali, G. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.126126 · Cited by 103
Bong, S. H., Nematollahi, B., Nazari, A., Xia, M., & Sanjayan, J. (2019) · Materials · doi:10.3390/ma12203410 · Cited by 100 · cited 3×
“Bong et al. [1] showed that adding polycarboxylate-and naphthalene-based SPs at 1% of precursor contents to FA-and GGBS-based one-part mixes activated via different types of sodium silicates caused a slight reduction in the compressive strength.”
BackgroundInfluentialStudy of seawater mixed one-part alkali activated GGBFS-fly ash
Lv, W., Sun, Z., & Su, Z. (2019) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2019.103484 · Cited by 94 · cited 1×
“Other water sources, such as sea water and reverse osmosis reject water, were also investigated to reduce the demand for fresh water [119 – 121].”
BackgroundMinimizing energy consumption to produce safe one-part alkali-activated materials
Refaat, M., Mohsen, A., Nasr, E.-S. A. R., & Kohail, M. (2021) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2021.129137 · Cited by 94
Rheology behavior of one-part alkali activated slag/glass powder (AASG) pastes
Li, L., Lu, J., Zhang, B., & Poon, C. S. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.120381 · Cited by 94 · cited 4×
“On the contrary, adding a small quantity of SF to GGBS-based one-part AAMs led to an improvement in initial flow, and caused a change in the shear stress-shear rate relationship by increasing the yield stress of the fresh mix and reducing the viscosity [163,164].”
BackgroundInfluentialAhmad, M. R., Chen, B., & Shah, S. F. A. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.120320 · Cited by 94 · cited 6×
“Water curing is usually avoided to prevent activator leaching [73,126].”
BackgroundMethodInfluentialCoppola, L., Coffetti, D., Crotti, E., Candamano, S., Crea, F., Gazzaniga, G., & Pastore, T. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.118682 · Cited by 93 · cited 1×
“[125] concluded that a combination of methylcellulose, modified starch and glycol-based shrinkage reducing admixture significantly retarded the setting of GGBS-based one-part AA pastes.”
BackgroundHigh strength/density ratio in a syntactic foam made from one-part mix geopolymer and cenospheres
Hajimohammadi, A., Ngo, T., Provis, J. L., Kim, T., & Vongsvivut, J. P. (2019) · Composites Part B Engineering · doi:10.1016/j.compositesb.2019.106908 · Cited by 90 · cited 2×
“The chemical composition of cenospheres is rich in SiO 2 and Al 2 O 3 and their mineral phase structure is generally amorphous with distinct crystalline peaks of quartz and mullite [16].”
BackgroundRoles of hybrid activators in improving the early-age properties of one-part geopolymer pastes
Wang, Y., Alrefaei, Y., & Dai, J. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.124880 · Cited by 89 · cited 4×
“Replacing a proportion of Na 2 SiO 3 with either NaOH, Na 2 CO 3 , NaAlO 2 or Na 2 SO 4 caused a reduction in the compressive strength of one-part AA systems [83,84,167,172].”
BackgroundMethodInfluentialHaruna, S., Mohammed, B. S., Wahab, M. M. A., & Liew, M. S. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.120024 · Cited by 89 · cited 2×
“Generally, a higher w/b and a lower aggregate/binder ratios result in higher initial flow [164,171].”
BackgroundSturm, P., Gluth, G. J. G., Simon, S., Brouwers, H. J. H., & Kühne, H. (2016) · Thermochimica Acta · doi:10.1016/j.tca.2016.04.015 · Cited by 87 · cited 1×
“Due to its high alumina content, NaAlO 2 was mainly combined with high silica precursors, such as RHA [54], SF [38,80], SR [81], and GS [37,82], or as substitutes to a proportion of Na 2 SiO 3 in FA-and GGBS-based mixes [13,83].”
MethodAbdel‐Gawwad, H. A., Rashad, A. M., & Heikal, M. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.05.356 · Cited by 87 · cited 3×
“Abdel-Gawwad et al. [61] used hydrothermal activation by mixing CoW powder with NaOH (5 – 20 wt% of CoW), and tap water (35 wt% of CoW powder) was added to the blend and heating was conducted at 60 ◦ C for 18 h.”
BackgroundMethodPreparation of one‐part geopolymeric precursors using vanadium tailing by thermal activation
Luo, Y., Bao, S., & Zhang, Y. (2019) · Journal of the American Ceramic Society · doi:10.1111/jace.16835 · Cited by 86 · cited 3×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
BackgroundGuo, X., Shi, H., & Wei, X. Y. (2017) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2017.01.007 · Cited by 86 · cited 1×
“Low-calcium FA, also known as Class F FA, is a by-product of burning bituminous coal in power plants [7], while high-calcium FA (Class C FA) is the result of burning lignite and sub-bituminous coal [8].”
BackgroundAbdel‐Gawwad, H. A., & Khalil, K. A. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.07.161 · Cited by 86 · cited 3×
“%) and feldspar (40 wt%), by calcining them at 1200/1300 ◦ C for 2 – 3 h in the presence of Na 2 CO 3 (0 – 20 wt% of CKD + feldspar) [43].”
BackgroundInfluentialPreparation of drying powder inorganic polymer cement based on alkali-activated slag technology
Wang, K.-T., Du, L.-Q., Lv, X., He, Y., & Cui, X. (2017) · Powder Technology · doi:10.1016/j.powtec.2017.02.036 · Cited by 85 · cited 1×
“Wang et al. [159] noticed a higher dissolution peak in the heat profile of GGBS-based one-part AAMs activated via Na 2 SiO 3 with an increase in activator content due to higher alkali concentration.”
BackgroundGuo, S., Ma, C., Long, G., & Xie, Y. (2019) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2019.02.116 · Cited by 85 · cited 5×
“Conventional FA contains spherical micro-beads which, depending on their density, can be classified as floating or sinking beads [13].”
BackgroundMethodInfluentialProperties and microstructure of lithium-slag-based geopolymer by one-part mixing method
Luo, Q., Wang, Y., Hong, S., Xing, F., & Dong, B. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.121723 · Cited by 84 · cited 2×
“Lithium slag (LS) was utilized as a precursor in recent one-part AAM studies [23,24].”
MethodAlrefaei, Y., Wang, Y., & Dai, J. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103917 · Cited by 83 · cited 1×
“Other studies [21,134] have mixed the solid raw materials together with 60 – 80% of the mixing water for a few minutes.”
BackgroundDeveloping one-part alkali-activated metakaolin/natural pozzolan binders using lime waste
Kadhim, A., Sadique, M., Al-Mufti, R. L., & Hashim, K. (2020) · Advances in Cement Research · doi:10.1680/jadcr.19.00118 · Cited by 83 · cited 5×
“For example, Kadhim et al. [67,71] showed that calcining LKD at 950 ◦ C to activate MK-based one-part AAMs helped enhance the compressive strength remarkably.”
BackgroundMethodInfluentialPreparation and characterization of one-part non-Portland cement
Abdel‐Gawwad, H. A., El-Aleem, S. A., & Ouda, A. S. (2015) · Ceramics International · doi:10.1016/j.ceramint.2015.08.096 · Cited by 83
Properties of alkali-activated mortar and concrete using lightweight aggregates
Yang, K., Song, J., & Lee, J.-S. (2009) · Materials and Structures · doi:10.1617/s11527-009-9499-6 · Cited by 82
Current developments and future needs in standards for cementitious materials
Hooton, R. D. (2015) · Cement and Concrete Research · doi:10.1016/j.cemconres.2015.05.022 · Cited by 82 · cited 1×
“The prescriptive nature of such standards limits the materials that can be used in the mix design process, and this has long been identified as an issue with existing concrete design standards and guidelines [195,196].”
BackgroundLong-Term Strength Development of Fly Ash-Based One-Part Alkali-Activated Binders
Haruna, S., Mohammed, B. S., Wahab, M. M. A., Kankia, M. U., Amran, M., & Gora, A. M. (2021) · Materials · doi:10.3390/ma14154160 · Cited by 82
A Roadmap for Production of Cement and Concrete with Low-CO2 Emissions
van Deventer, J. S. J., White, C. E., & Myers, R. J. (2020) · Waste and Biomass Valorization · doi:10.1007/s12649-020-01180-5 · Cited by 81 · cited 1×
“In a recent publication, van Deventer et al. [200] set out a framework for future performance-based design standards to ensure their wide-scale deployment.”
BackgroundSolid Reactant-Based Geopolymers from Rice Hull Ash and Sodium Aluminate
Hajimohammadi, A., & van Deventer, J. S. J. (2016) · Waste and Biomass Valorization · doi:10.1007/s12649-016-9735-6 · Cited by 77
Yang, K., Sim, J.-I., & Nam, S. (2009) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2009.09.001 · Cited by 77 · cited 2×
“Yang et al. [87] reported that water curing of GGBS-based one-part mixes activated via a combination of Ca(OH) 2 and Ba (OH) 2 resulted in significantly higher strengths (as much as 201% increase) than ambient air curing.”
BackgroundCompressive strength, microstructure and hydration products of hybrid alkaline cements
Abdollahnejad, Z., Hlavacek, P., Miraldo, S., Pacheco-Torgal, F., & de Aguiar, J. L. B. (2014) · Materials Research · doi:10.1590/s1516-14392014005000091 · Cited by 76
Abdollahnejad, Z., Luukkοnen, T., Mastali, M., Giosué, C., Favoni, O., Ruello, M. L., Kinnunen, P., & Illikainen, M. (2019) · Waste and Biomass Valorization · doi:10.1007/s12649-019-00626-9 · Cited by 75 · cited 1×
“Ceramic waste (CW), originally made of clay and other earth materials, has also found application as a precursor due to its high SiO 2 and Al 2 O 3 contents [62,63].”
BackgroundHydration mechanisms of hybrid cements as a function of the way of addition of chemicals
Fernández‐Jiménez, A., García-Lodeiro, I., Maltseva, O., & Palomo, A. (2018) · Journal of the American Ceramic Society · doi:10.1111/jace.15939 · Cited by 75
Preparation and properties of rubberised geopolymer concrete: A review
El-Zeadani, M., Bompa, D. V., & Elghazouli, A. Y. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.125504 · Cited by 73
Self-citationSynthesis of kaolin-based alkali-activated cement: carbon footprint, cost and energy assessment
Ababneh, A. N., Matalkah, F., & Aqel, R. (2020) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2020.05.116 · Cited by 73 · cited 1×
“Ababneh et al. [130] used thermal activation to pre-treat kaolinite clay in the presence of CaO, Na 2 CO 3 and Na 2 SiO 3 ⋅ 5H 2 O.”
BackgroundPeng, M. X., Wang, Z. H., Xiao, Q. G., Song, F., Xie, W., Yu, L. C., Huang, H. W., & Yi, S. J. (2017) · Applied Clay Science · doi:10.1016/j.clay.2017.01.020 · Cited by 72 · cited 2×
“Heat curing of one-part AAMs made from different precursor bases, including GGBS, MK, volcanic tuff, bentonite and dolomite, was seen to contribute to significant improvement in the compressive strength [71,103,110,185].”
BackgroundInfluentialHigh strength one-part alkali-activated slag blends designed by particle packing optimization
Perumal, P., Sreenivasan, H., Luukkοnen, T., Kantola, A. M., Telkki, V., Kinnunen, P., & Illikainen, M. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.124004 · Cited by 72 · cited 7×
“Blending low-calcium and high-calcium binders in one-part AAMs leads to the development of cross-linked N-A-S-H and C-A-S-H gels [10,139,156].”
BackgroundInfluentialAbdollahnejad, Z., Miraldo, S., Pacheco-Torgal, F., & de Aguiar, J. L. B. (2015) · European Journal of Environmental and Civil engineering · doi:10.1080/19648189.2015.1125392 · Cited by 71
The Durability of One-Part Alkali-Activated Slag-Based Mortars in Different Environments
Coppola, L., Coffetti, D., Crotti, E., Gazzaniga, G., & Pastore, T. (2020) · Sustainability · doi:10.3390/su12093561 · Cited by 71 · cited 4×
“Furthermore, GGBS-based one-part AAMs showed significantly better resistance to CaCl 2 solutions when compared to OPC-based CCM [166], and this merits their use in structures in contact with CaCl 2 de-icing salts.”
BackgroundMethodInfluentialSturm, P., Greiser, S., Gluth, G. J. G., Jäger, C., & Brouwers, H. J. H. (2015) · Journal of Materials Science · doi:10.1007/s10853-015-9232-5 · Cited by 70 · cited 2×
“Silica residue (SR), a waste residue from chlorosilane production, was also utilized as a source of additional SiO 2 [38,39], and its SiO 2 content is in the range of 84 – 89%.”
MethodSamarakoon, M. H., Ranjith, P. G., Duan, W., Haque, A., & Chen, B. K. (2021) · Waste Management · doi:10.1016/j.wasman.2021.04.060 · Cited by 70 · cited 3×
“Hydrothermal activation was also used to produce a solid activator for one-part AAMs [59].”
MethodInfluentialOne-part alkali activated cement based volcanic pumice
Almalkawi, A. T., Hamadna, S., & Soroushian, P. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.06.139 · Cited by 70 · cited 4×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
BackgroundMethodInfluentialVu, T. H., Gowripalan, N., Silva, P. D., Paradowska, A. M., Garbe, U., Kidd, P., & Sirivivatnanon, V. (2020) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2020.103759 · Cited by 69
Aseniero, J. P. J., Opiso, E. M., Banda, M. H. T., & Tabelin, C. B. (2018) · SN Applied Sciences · doi:10.1007/s42452-018-0045-4 · Cited by 68 · cited 1×
“1 [52].”
Effects of mixing water temperatures on properties of one-part alkali-activated slag paste
Almakhadmeh, M., & Soliman, A. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.121030 · Cited by 68
Chemical Stability and Leaching Behavior of One-Part Geopolymer from Soil and Coal Fly Ash Mixtures
Tigue, A. A. S., Malenab, R. A. J., Dungca, J. R., Yu, D. E. C., & Promentilla, M. A. B. (2018) · Minerals · doi:10.3390/min8090411 · Cited by 67
Performance investigation of high-proportion Saudi-fly-ash-based concrete
Amran, M., Soto, M. G., Alyousef, R., El-Zeadani, M., Alabduljabbar, H., & Aune, V. (2020) · Results in Engineering · doi:10.1016/j.rineng.2020.100118 · Cited by 65 · cited 1×
“Low-calcium FA, also known as Class F FA, is a by-product of burning bituminous coal in power plants [7], while high-calcium FA (Class C FA) is the result of burning lignite and sub-bituminous coal [8].”
BackgroundSelf-citationPromoting the performance of one-part alkali-activated slag using fine lead-zinc mine tailings
Chen, W., Peng, R., Straub, C. C., & Yuan, B. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.117745 · Cited by 64 · cited 3×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
BackgroundMethodÇetintaş, R., & Soyer‐Uzun, S. (2018) · Journal of Building Engineering · doi:10.1016/j.jobe.2018.07.011 · Cited by 63 · cited 3×
“…aluminosilicate precursors: Class F FA [42] , Class C FA [90] , GGBS [124] , NS [31] , LS [23] , SF [164] , SR [39] , GS [209] , WG [164] , phyllite dust [139] , RHA [34] , pumice [70] , Volcanic tuff [67] , Volcanic ash [72] , VT [49] , Kaolin [210] , MK [210] , GMT [45] , LZMT [48] , OPC [117].”
BackgroundMethodMin, Y., Wu, J. H., Li, B., & Zhang, J. (2021) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0003887 · Cited by 61
Peys, A., Arnout, L., Blanpain, B., Rahier, H., Acker, K. V., & Pontikes, Y. (2017) · Waste and Biomass Valorization · doi:10.1007/s12649-017-9877-1 · Cited by 59 · cited 2×
“For instance, Maize stalk ash (MSA) and maize cob ash (MCA) from burning maize stalk and cob, respectively, were utilized as solid activators [28,96].”
BackgroundMethodA novel non-Portland cementitious material: Mechanical properties, durability and characterization
Zhou, S., Ma, C., Long, G., & Xie, Y. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.117671 · Cited by 59 · cited 10×
“As such, the reaction process of one-part AAMs in most cases can be divided into four stages: a) pre-induction period, b) induction period, c) acceleration period and d) deceleration period [11,13,94].”
BackgroundMethodInfluentialBridging the gap between research and standards
Hooton, R. D. (2007) · Cement and Concrete Research · doi:10.1016/j.cemconres.2007.09.012 · Cited by 58
Flow and Compressive Strength of Alkali-Activated Mortars
Yang, K., Song, J., Lee, K., & Ashour, A. F. (2009) · ACI Materials Journal · doi:10.14359/56316 · Cited by 57 · cited 4×
“Sodium hydroxides, despite their higher pH, usually come second to Na 2 SiO 3 when considering compressive strength development [172].”
BackgroundInfluentialDevelopment of One-Part Alkali-Activated Ceramic/Slag Binders Containing Recycled Ceramic Aggregates
Abdollahnejad, Z., Luukkοnen, T., Mastali, M., Kinnunen, P., & Illikainen, M. (2018) · Journal of Materials in Civil Engineering · doi:10.1061/(asce)mt.1943-5533.0002608 · Cited by 57 · cited 2×
“The sources of natural aggregate replacements include crushed bricks [112], WG [113,114], CW [62,115], waste sands [107], crumb rubber [116], and sand derived from IMT waste [103].”
BackgroundOne-part alkali-activated blast furnace slag for sustainable construction at subzero temperatures
Alzaza, A., Ohenoja, K., & Illikainen, M. (2021) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.122026 · Cited by 56 · cited 4×
“For instance, GGBS-based one-part AAMs cured at (cid:0) 5 ◦ C were able to achieve a 56-day compressive strength of nearly 68 MPa, while OPC-based CCM mixes cured at the same temperature resulted in a 56-day strength of about 10 MPa [187].”
BackgroundInfluentialZheng, H., He, Y., Zhu, Y., Liu, L., & Cui, X. (2021) · RSC Advances · doi:10.1039/d1ra01353j · Cited by 55
Dry powder alkali-activated slag cements
Kovtun, M., Kearsley, E. P., & Shekhovtsova, J. (2015) · Advances in Cement Research · doi:10.1680/jadcr.14.00078 · Cited by 54
Yang, T., Zhang, Z., Zhu, H., Zhang, W., Gao, Y., Zhang, X., & Wu, Q. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.03.245 · Cited by 54 · cited 3×
“Nickel slag (NS), a waste material from nickel-alloy production, was recently used in one-part AAMs [31,32].”
BackgroundMethodYang, B., & Jang, J. G. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.119552 · Cited by 54 · cited 1×
“[101].”
Mechanical and Durability Performance of Novel Self-activating Geopolymer Mortars
Cheah, C. B., Ken, P. W., & Ramli, M. B. (2017) · Procedia Engineering · doi:10.1016/j.proeng.2017.01.374 · Cited by 53
Lu, J., Yu, Z., Zhu, Y., Huang, S., Luo, Q., & Zhang, S. (2019) · Materials · doi:10.3390/ma12101652 · Cited by 52 · cited 1×
“The chemical composition of LS mainly consists of SiO 2 , Al 2 O 3 and sodium oxide (Na 2 O) [26].”
BackgroundFigueiredo, R. A. M., Silveira, A. B. M., Melo, E. L. P., Costa, G. Q. G., Brandão, P. R. G., Aguilar, M. T. P., Henriques, A. B., & Mazzinghy, D. B. (2021) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2021.07.153 · Cited by 51 · cited 1×
“IMTs, meanwhile, show chemical compositions that are rich in SiO 2 and Fe 2 O 3 , and have a crystalline phase structure with peaks including quartz, muscovite, and hematite [47].”
BackgroundAlrefaei, Y., & Dai, J. (2022) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2022.126611 · Cited by 50 · cited 2×
“In a recent study, Alrefaei and Dai [138] examined the effect of delayed SP addition, in this case a polycarboxylate ether, on the resulting rheological and mechanical properties of FA-and GGBS-based one-part AA pastes.”
BackgroundDurability Performance of Fly Ash Based One-Part Geopolymer Mortars
Abdollahnejad, Z., Pacheco-Torgal, F., de Aguiar, J. L. B., & Jesus, C. M. G. (2014) · Key engineering materials · doi:10.4028/www.scientific.net/kem.634.113 · Cited by 49
Wei, T., Zhao, H., & Ma, C. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.121715 · Cited by 48 · cited 5×
“For instance, GGBS-based mixtures tend to have a more compact pore structure when compared to sole FA-based mixes [190], binary GGBS-and FASB-based pastes [12,167] or binary LS-and GGBS-based systems [23] due to the nature of hydration products formed.”
BackgroundMethodInfluentialPreparation of one-part alkali-activated nickel slag binder using an optimal ball milling process
Wang, X., Wu, W., Zhang, L., Fu, L., & Li, X. (2022) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2021.125902 · Cited by 47
Zhou, S., Tan, C., Gao, Y., Li, Y., & Guo, S. (2021) · Materials Research Express · doi:10.1088/2053-1591/ac16f4 · Cited by 47 · cited 2×
“More recently, however, Zhou et al. [178] showed that combining Na 2 CO 3 with Ca(OH) 2 to activate GGBS-based one-part mixes could attain compressive strengths that are 60% higher than the same mixes activated using NaOH.”
MethodFrom NORM by-products to building materials
Labrincha, J. A., Puertas, F., Schroeyers, W., Kovler, K., Pontikes, Y., Nuccetelli, C., Krivenko, P. V., Kovalchuk, O. Y., Petropavlovsky, О., Komljenović, M. M., et al. (2017) · Elsevier eBooks · doi:10.1016/b978-0-08-102009-8.00007-4 · Cited by 47
Waste-Based One-Part Alkali Activated Materials
Gonçalves, M., Vilarinho, I. S., Capela, M. N., Caetano, A. P. F., Novais, R. M., Labrincha, J. A., & Seabra, M. P. D. S. (2021) · Materials · doi:10.3390/ma14112911 · Cited by 44 · cited 3×
“The sources of natural aggregate replacements include crushed bricks [112], WG [113,114], CW [62,115], waste sands [107], crumb rubber [116], and sand derived from IMT waste [103].”
BackgroundInfluentialCoppola, L., Coffetti, D., Crotti, E., Marini, A., Passoni, C., & Pastore, T. (2019) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2019.103341 · Cited by 42 · cited 1×
“The sources of natural aggregate replacements include crushed bricks [112], WG [113,114], CW [62,115], waste sands [107], crumb rubber [116], and sand derived from IMT waste [103].”
BackgroundFont, A., Soriano, L., TASHIMA, M. M., Monzó, J., Borrachero, M. V., & Payá, J. (2020) · Journal of Cleaner Production · doi:10.1016/j.jclepro.2020.122203 · Cited by 41 · cited 2×
“Aluminum powder, hydrogen peroxide (H 2 O 2 ), and surfactant were used as admixtures to form foamed one-part AAMs [97,128].”
MethodLiu, C., Yao, X., & Zhang, W. (2019) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2019.117091 · Cited by 41
Alzaza, A., Ohenoja, K., & Illikainen, M. (2021) · Cement and Concrete Composites · doi:10.1016/j.cemconcomp.2021.104128 · Cited by 40 · cited 4×
“Alzaza et al. [129] investigated the effect of basic oxygen furnace (BOF) submicron particles on the reactivity of one-part GGBS-based AAMs in sub-zero conditions.”
BackgroundInfluentialGeopolymerization of a silica residue from waste treatment of chlorosilane production
Gluth, G. J. G., Lehmann, C. W., Rübner, K., & Kühne, H. (2012) · Materials and Structures · doi:10.1617/s11527-012-9972-5 · Cited by 37 · cited 2×
“Silica residue (SR), a waste residue from chlorosilane production, was also utilized as a source of additional SiO 2 [38,39], and its SiO 2 content is in the range of 84 – 89%.”
BackgroundMethodCements with a low clinker content: versatile use of raw materials
García-Lodeiro, I., Fernández‐Jiménez, A., & Palomo, A. (2015) · Journal of Sustainable Cement-Based Materials · doi:10.1080/21650373.2015.1040865 · Cited by 36
Long-Term Strength Evolution in Ambient-Cured Solid-Activator Geopolymer Compositions
Wong, V., Jervis, W., Fishburn, B., Numata, T., Joe, W., Rawal, A., Sorrell, C. C., & Koshy, P. (2021) · Minerals · doi:10.3390/min11020143 · Cited by 36 · cited 1×
“2) [9].”
Recent advances in blended alkali-activated cements: a review
Rakhimova, N. R. (2020) · European Journal of Environmental and Civil engineering · doi:10.1080/19648189.2020.1858170 · Cited by 36 · cited 3×
“GGBS is another industrial by-product that was used intensively in one-part AAMs and has an annual generation rate of 270 – 390 million tons [14].”
BackgroundInfluentialGuo, W., Zhang, Z., Xu, Z., Zhang, J., Bai, Y., Zhao, Q., & Qiu, Y. (2022) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2022.127352 · Cited by 35 · cited 6×
“Soda residue, with its high CaO content (~40 wt%), was also investigated as a solid activator in combination with CCR to form FA and GGBS-based AAMs [103 – 105].”
BackgroundMethodInfluentialAbdelmonim, A., & Bompa, D. V. (2021) · Infrastructures · doi:10.3390/infrastructures6100146 · Cited by 34 · cited 2×
“The sources of natural aggregate replacements include crushed bricks [112], WG [113,114], CW [62,115], waste sands [107], crumb rubber [116], and sand derived from IMT waste [103].”
BackgroundSelf-citationAlkaline Activation of Basic Oxygen Furnace Slag Modified Gold Mine Tailings for Building Material
Mashifana, T., Sebothoma, J., & Sithole, T. (2021) · Advances in Civil Engineering · doi:10.1155/2021/9984494 · Cited by 34 · cited 1×
“Recent investigations on one-part AAMs used gold mine tailings (GMT), iron ore mine tailings (IMT), lead-zinc mine tailings (LZMT), and vanadium tailings (VT) as precursors [46 – 50].”
BackgroundRadiological characterization of anhydrous/hydrated cements and geopolymers
Puertas, F., Alonso, M. M., Torres‐Carrasco, M., Rivilla, P., Gascó, C., Yagüe, L., Suárez, J. A., & Navarro, N. (2015) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2015.10.074 · Cited by 33 · cited 5×
“For materials used predominantly or partially (e. g., walls, basements), an ACI value of 0.5 or less indicates a radiation dose of about 0.3 mSv, while an ACI value of 1 indicates a dose of 1 mSv [202].”
BackgroundMethodInfluentialChen, B., Wang, J., & Zhao, J. (2021) · Advances in Materials Science and Engineering · doi:10.1155/2021/6658588 · Cited by 33 · cited 2×
“…delay in setting due to NaAlO 2 addition occurs as aluminate species coagulate the silicate species in Na 2 SiO 3 and absorb to the precursor particles, which could generate negative charge sites that repel the OH (cid:0) responsible for catalysing the dissolution of aluminosilicate species [169].”
BackgroundMetakaolin-based inorganic polymer synthesis using cotton shell ash as sole alkaline activator
Madi, A. B., Rahier, H., Mobili, A., Katsiki, A., Fagel, N., Chinje, U. M., & Njopwouo, D. (2018) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2018.10.047 · Cited by 32 · cited 5×
“2 and its mineral phase structure shows crystalline peaks of quartz, illite, anatase and calcite [65].”
BackgroundMethodInfluentialBao, S., Luo, Y., & Zhang, Y. (2022) · International Journal of Minerals Metallurgy and Materials · doi:10.1007/s12613-020-2182-1 · Cited by 32 · cited 1×
“VT, a predominant waste from extracting vanadium, was used mainly in combination with MK [49,50,53].”
Azevedo, A. G. D. S., & Strecker, K. (2020) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2020.121306 · Cited by 30
Masi, G., Filipponi, A., & Bignozzi, M. C. (2021) · Open Ceramics · doi:10.1016/j.oceram.2021.100178 · Cited by 30 · cited 1×
“Masi et al. [132] also showed improvement in the mechanical properties of FA-based one-part AAMs when the FA was ball milled with potassium hydroxide (KOH) and Na 2 SiO 3 -anhydrous for 2 h.”
MethodMatalkah, F., & Soroushian, P. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.10.002 · Cited by 30
Cited by
Hamsashree, Souza, S. S. D., Pandit, P., & Kumar, Y. M. A. (2025) · Discover Applied Sciences · doi:10.1007/s42452-025-07711-w · Cited by 11
Metadata
- Authors
- Elzeadani, M., Bompa, D. V., & Elghazouli, A. Y.
- Venue
- Journal of Building Engineering
- Publisher
- Elsevier BV
- Published
- 2022-10
- Volume
- 57
- Pages
- 104871
- ISSN
- 2352-7102 (ISSN-L)
- OpenAlex
- W4283591704
- Cited by
- 180
- References
- 217
- FWCI
- 16.62
- Type
- journal article
- Language
- en
- Open access
- hybrid
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.