The DOI matches its Crossref record; 290 of the 290 references it cites were found in a registry or an index.
Direct Ink Writing: A 3D Printing Technology for Diverse Materials
Abstract
Additive manufacturing (AM) has gained significant attention due to its ability to drive technological development as a sustainable, flexible, and customizable manufacturing scheme. Among the various AM techniques, direct ink writing (DIW) has emerged as the most versatile 3D printing technique for the broadest range of materials. DIW allows printing of practically any material, as long as the precursor ink can be engineered to demonstrate appropriate rheological behavior. This technique acts as a unique pathway to introduce design freedom, multifunctionality, and stability simultaneously into its printed structures. Here, a comprehensive review of DIW of complex 3D structures from various materials, including polymers, ceramics, glass, cement, graphene, metals, and their combinations through multimaterial printing is presented. The review begins with an overview of the fundamentals of ink rheology, followed by an in‐depth discussion of the various methods to tailor the ink for DIW of different classes of materials. Then, the diverse applications of DIW ranging from electronics to food to biomedical industries are discussed. Finally, the current challenges and limitations of this technique are highlighted, followed by its prospects as a guideline toward possible futuristic innovations.
Overview
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Integrity signals
Registry
Cites
Statistics
Verification
Claims the paper makes
The claims and statistics of this paper haven’t been checked yet.
Run the check — free, no account needed. It reads the open-access text and checks the sources it cites.
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
The self-check needs the paper’s full text.
Citations
Cites
Sydney Gladman, A., Matsumoto, E. A., Nuzzo, R. G., Mahadevan, L., & Lewis, J. A. (2016) · Nature Materials · doi:10.1038/nmat4544 · Cited by 3,027
Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing
Gibson, I., Rosen, D. W., & Stucker, B. (2010) · National University of Singapore · doi:10.1007/978-1-4419-1120-9 · Cited by 2,969
A 3D bioprinting system to produce human-scale tissue constructs with structural integrity
Kang, H.-W., Lee, S. J., Ko, I. K., Kengla, C., Yoo, J. J., & Atala, A. (2016) · Nature Biotechnology · doi:10.1038/nbt.3413 · Cited by 2,622
Gogotsi, Y., & Anasori, B. (2019) · ACS Nano · doi:10.1021/acsnano.9b06394 · Cited by 2,541
Printing ferromagnetic domains for untethered fast-transforming soft materials
Kim, Y., Yuk, H., Zhao, R., Chester, S. A., & Zhao, X. (2018) · Nature · doi:10.1038/s41586-018-0185-0 · Cited by 2,183
Advanced structural ceramics in aerospace propulsion
Padture, N. P. (2016) · Nature Materials · doi:10.1038/nmat4687 · Cited by 2,148
An integrated design and fabrication strategy for entirely soft, autonomous robots
Wehner, M., Truby, R. L., Fitzgerald, D. J., Mosadegh, B., Whitesides, G. M., Lewis, J. A., & Wood, R. J. (2016) · Nature · doi:10.1038/nature19100 · Cited by 2,127
3D printing of ceramics: A review
Chen, Z., Li, Z., Li, J., Liu, C., Lao, C., Fu, Y., Liu, C., Li, Y., Wang, P., & He, Y. (2019) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2018.11.013 · Cited by 2,109
3D bioprinting of vascularized, heterogeneous cell-laden tissue constructs
Kolesky, D. B., Truby, R. L., Gladman, A. S., Busbee, T. A., Homan, K. A., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201305506 · Cited by 2,102
Polymer‐Derived Ceramics: 40 Years of Research and Innovation in Advanced Ceramics
Colombo, P., Mera, G., Riedel, R., & Sorarù, G. D. (2010) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2010.03876.x · Cited by 1,887
Flexible mechanical metamaterials
Bertoldi, K., Vitelli, V., Christensen, J., & van Hecke, M. (2017) · Nature Reviews Materials · doi:10.1038/natrevmats.2017.66 · Cited by 1,867
Additive manufacturing and its societal impact: a literature review
Huang, S. H., Liu, P., Mokasdar, A., & Hou, L. (2013) · The International Journal of Advanced Manufacturing Technology · doi:10.1007/s00170-012-4558-5 · Cited by 1,862
Hinton, T. J., Jallerat, Q., Palchesko, R. N., Park, J. H., Grodzicki, M. S., Shue, H.-J., Ramadan, M. H., Hudson, A. R., & Feinberg, A. W. (2015) · Science Advances · doi:10.1126/sciadv.1500758 · Cited by 1,805
Park, S., Lee, K.-S., Bozoklu, G., Cai, W., Nguyen, S. T., & Ruoff, R. S. (2008) · ACS Nano · doi:10.1021/nn700349a · Cited by 1,781
Direct Ink Writing of 3D Functional Materials
Lewis, J. A. (2006) · Advanced Functional Materials · doi:10.1002/adfm.200600434 · Cited by 1,740
3D‐Printing of Lightweight Cellular Composites
Compton, B. G., & Lewis, J. A. (2014) · Advanced Materials · doi:10.1002/adma.201401804 · Cited by 1,626
Current advances and future perspectives in extrusion-based bioprinting
Ozbolat, I. T., & Hospodiuk, M. (2016) · Biomaterials · doi:10.1016/j.biomaterials.2015.10.076 · Cited by 1,572
Three-dimensional bioprinting of thick vascularized tissues
Kolesky, D. B., Homan, K. A., Skylar-Scott, M. A., & Lewis, J. A. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1521342113 · Cited by 1,492
Materials with structural hierarchy
Lakes, R. (1993) · Nature · doi:10.1038/361511a0 · Cited by 1,402
3D Printing of Interdigitated Li‐Ion Microbattery Architectures
Sun, K., Wei, T., Ahn, B. Y., Seo, J. Y., Dillon, S. J., & Lewis, J. A. (2013) · Advanced Materials · doi:10.1002/adma.201301036 · Cited by 1,341
Scaffold-free vascular tissue engineering using bioprinting
Norotte, C., Marga, F. S., Niklason, L. E., & Forgacs, G. (2009) · Biomaterials · doi:10.1016/j.biomaterials.2009.06.034 · Cited by 1,339
Bos, F., Wolfs, R., Ahmed, Z., & Salet, T. (2016) · Virtual and Physical Prototyping · doi:10.1080/17452759.2016.1209867 · Cited by 1,257
Developments in construction-scale additive manufacturing processes
Lim, S., Buswell, R. A., Le, T. T., Austin, S. A., Gibb, A. G. F., & Thorpe, T. (2012) · Automation in Construction · doi:10.1016/j.autcon.2011.06.010 · Cited by 1,205
Omnidirectional Printing of Flexible, Stretchable, and Spanning Silver Microelectrodes
Ahn, B. Y., Duoss, E. B., Motala, M. J., Guo, X., Park, S.-I., Xiong, Y., Yoon, J., Nuzzo, R. G., Rogers, J. A., & Lewis, J. A. (2009) · Science · doi:10.1126/science.1168375 · Cited by 1,191
Momeni, F., M.Mehdi Hassani.N, S., Liu, X., & Ni, J. (2017) · Materials & Design · doi:10.1016/j.matdes.2017.02.068 · Cited by 1,165
Highly compressible 3D periodic graphene aerogel microlattices
Zhu, C., Han, T. Y.-J., Duoss, E. B., Golobic, A. M., Kuntz, J. D., Spadaccini, C. M., & Worsley, M. A. (2015) · Nature Communications · doi:10.1038/ncomms7962 · Cited by 1,148
Direct 3D Printing of Shear‐Thinning Hydrogels into Self‐Healing Hydrogels
Highley, C. B., Rodell, C. B., & Burdick, J. A. (2015) · Advanced Materials · doi:10.1002/adma.201501234 · Cited by 1,043
Voxelated soft matter via multimaterial multinozzle 3D printing
Skylar-Scott, M. A., Mueller, J., Visser, C. W., & Lewis, J. A. (2019) · Nature · doi:10.1038/s41586-019-1736-8 · Cited by 1,024
Hardened properties of high-performance printing concrete
Le, T. T., Austin, S. A., Lim, S., Buswell, R. A., Law, R., Gibb, A. G. F., & Thorpe, T. (2012) · Cement and Concrete Research · doi:10.1016/j.cemconres.2011.12.003 · Cited by 1,020
Billiet, T., Gevaert, E., De Schryver, T., Cornelissen, M., & Dubruel, P. (2014) · Biomaterials · doi:10.1016/j.biomaterials.2013.09.078 · Cited by 1,015
Hydraulic hydrogel actuators and robots optically and sonically camouflaged in water
Yuk, H., Lin, S., Ma, C., Takaffoli, M., Fang, N. X., & Zhao, X. (2017) · Nature Communications · doi:10.1038/ncomms14230 · Cited by 988
On the origin of the stability of graphene oxide membranes in water
Yeh, C.-N., Raidongia, K., Shao, J., Yang, Q.-H., & Huang, J. (2015) · Nature Chemistry · doi:10.1038/nchem.2145 · Cited by 961
Biomanufacturing of organ-specific tissues with high cellular density and embedded vascular channels
Skylar-Scott, M. A., Uzel, S. G. M., Nam, L. L., Ahrens, J. H., Truby, R. L., Damaraju, S., & Lewis, J. A. (2019) · Science Advances · doi:10.1126/sciadv.aaw2459 · Cited by 943
3D printing of soft robotic systems
Wallin, T. J., Pikul, J., & Shepherd, R. F. (2018) · Nature Reviews Materials · doi:10.1038/s41578-018-0002-2 · Cited by 942
3D Printing of Free Standing Liquid Metal Microstructures
Ladd, C., So, J., Muth, J., & Dickey, M. D. (2013) · Advanced Materials · doi:10.1002/adma.201301400 · Cited by 926
Advances in crosslinking strategies of biomedical hydrogels
Hu, W., Wang, Z., Xiao, Y., Zhang, S., & Wang, J. (2019) · Biomaterials Science · doi:10.1039/c8bm01246f · Cited by 896
3D Printing of Highly Stretchable and Tough Hydrogels into Complex, Cellularized Structures
Hong, S., Sycks, D., Chan, H. F., Lin, S., Lopez, G. P., Guilak, F., Leong, K. W., & Zhao, X. (2015) · Advanced Materials · doi:10.1002/adma.201501099 · Cited by 873
3D printing: Printing precision and application in food sector
Liu, Z., Zhang, M., Bhandari, B., & Wang, Y. (2017) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2017.08.018 · Cited by 858
Additive manufacturing of advanced ceramic materials
Lakhdar, Y., Tuck, C., Binner, J., Terry, A., & Goodridge, R. (2021) · Progress in Materials Science · doi:10.1016/j.pmatsci.2020.100736 · Cited by 857
Whitesides, G. M. (2018) · Angewandte Chemie International Edition · doi:10.1002/anie.201800907 · Cited by 850
Multimaterial magnetically assisted 3D printing of composite materials
Kokkinis, D., Schaffner, M., & Studart, A. R. (2015) · Nature Communications · doi:10.1038/ncomms9643 · Cited by 848
Direct Ink Writing of Three‐Dimensional Ceramic Structures
Lewis, J. A., Smay, J. E., Stuecker, J., & Cesarano, J. (2006) · Journal of the American Ceramic Society · doi:10.1111/j.1551-2916.2006.01382.x · Cited by 823
Omnidirectional Printing of 3D Microvascular Networks
Wu, W., DeConinck, A., & Lewis, J. A. (2011) · Advanced Materials · doi:10.1002/adma.201004625 · Cited by 819
3D printing of liquid crystal elastomeric actuators with spatially programed nematic order
Kotikian, A., Truby, R. L., Boley, J. W., White, T. J., & Lewis, J. A. (2018) · Advanced Materials · doi:10.1002/adma.201706164 · Cited by 768
Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material
Panda, B., Paul, S. C., & Tan, M. J. (2017) · Materials Letters · doi:10.1016/j.matlet.2017.07.123 · Cited by 742
Supercapacitors Based on Three-Dimensional Hierarchical Graphene Aerogels with Periodic Macropores
Zhu, C., Liu, T., Qian, F., Han, T. Y.-J., Duoss, E. B., Kuntz, J. D., Spadaccini, C. M., Worsley, M. A., & Li, Y. (2016) · Nano Letters · doi:10.1021/acs.nanolett.5b04965 · Cited by 720
Meng, X., & Karniadakis, G. E. (2020) · Journal of Computational Physics · doi:10.1016/j.jcp.2019.109020 · Cited by 713
Jakus, A. E., Secor, E. B., Rutz, A. L., Jordan, S. W., Hersam, M. C., & Shah, R. N. (2015) · ACS Nano · doi:10.1021/acsnano.5b01179 · Cited by 710
Colloidal Inks for Directed Assembly of 3-D Periodic Structures
Smay, J. E., Cesarano, J., & Lewis, J. A. (2002) · Langmuir · doi:10.1021/la0257135 · Cited by 700
Additive manufacturing of silica aerogels
Zhao, S., Siqueira, G., Drdova, S., Norris, D., Ubert, C., Bonnin, A., Galmarini, S., Ganobjak, M., Pan, Z., Brunner, S., et al. (2020) · Nature · doi:10.1038/s41586-020-2594-0 · Cited by 676
Fresh and hardened properties of 3D printable cementitious materials for building and construction
Paul, S. C., Tay, Y. W. D., Panda, B., & Tan, M. J. (2018) · Archives of Civil and Mechanical Engineering · doi:10.1016/j.acme.2017.02.008 · Cited by 633
Conformal Printing of Electrically Small Antennas on Three‐Dimensional Surfaces
Adams, J. J., Duoss, E. B., Malkowski, T. F., Motala, M. J., Ahn, B. Y., Nuzzo, R. G., Bernhard, J. T., & Lewis, J. A. (2011) · Advanced Materials · doi:10.1002/adma.201003734 · Cited by 630
3D Printing of Shear-Thinning Hyaluronic Acid Hydrogels with Secondary Cross-Linking
Ouyang, L., Highley, C. B., Rodell, C. B., Sun, W., & Burdick, J. A. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00158 · Cited by 607
Cellulose Nanocrystal Inks for 3D Printing of Textured Cellular Architectures
Siqueira, G., Kokkinis, D., Libanori, R., Hausmann, M. K., Gladman, A. S., Neels, A., Tingaut, P., Zimmermann, T., Lewis, J. A., & Studart, A. R. (2017) · Advanced Functional Materials · doi:10.1002/adfm.201604619 · Cited by 580
Hydrogels as intelligent materials: A brief review of synthesis, properties and applications
Mahinroosta, M., Jomeh Farsangi, Z., Allahverdi, A., & Shakoori, Z. (2018) · Materials Today Chemistry · doi:10.1016/j.mtchem.2018.02.004 · Cited by 551
Topology Optimized Architectures with Programmable Poisson's Ratio over Large Deformations
Clausen, A., Wang, F., Jensen, J. S., Sigmund, O., & Lewis, J. A. (2015) · Advanced Materials · doi:10.1002/adma.201502485 · Cited by 551
Impact of rheological properties of mashed potatoes on 3D printing
Liu, Z., Zhang, M., Bhandari, B., & Yang, C. (2018) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2017.04.017 · Cited by 550
Mechanical properties and shape memory effect of 3D-printed PLA-based porous scaffolds
Senatov, F. S., Niaza, K. V., Zadorozhnyy, M. Y., Maksimkin, A. V., Kaloshkin, S. D., & Estrin, Y. Z. (2016) · Journal of the Mechanical Behavior of Biomedical Materials · doi:10.1016/j.jmbbm.2015.11.036 · Cited by 547
Direct Writing of Gallium‐Indium Alloy for Stretchable Electronics
Boley, J. W., White, E. L., Chiu, G. T. ‐., & Kramer, R. K. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201303220 · Cited by 546
Rapid energy-efficient manufacturing of polymers and composites via frontal polymerization
Robertson, I. D., Yourdkhani, M., Centellas, P. J., Aw, J. E., Ivanoff, D. G., Goli, E., Lloyd, E. M., Dean, L. M., Sottos, N. R., Geubelle, P. H., et al. (2018) · Nature · doi:10.1038/s41586-018-0054-x · Cited by 527
4D Printing with Mechanically Robust, Thermally Actuating Hydrogels
Bakarich, S. E., Gorkin, R., Panhuis, M. I. H., & Spinks, G. M. (2015) · Macromolecular Rapid Communications · doi:10.1002/marc.201500079 · Cited by 526
Ouyang, L., Highley, C. B., Sun, W., & Burdick, J. A. (2017) · Advanced Materials · doi:10.1002/adma.201604983 · Cited by 524
3D Printing of Highly Stretchable, Shape-Memory, and Self-Healing Elastomer toward Novel 4D Printing
Kuang, X., Chen, K., Dunn, C. K., Wu, J., Li, V. C. F., & Qi, H. J. (2018) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b18265 · Cited by 523
3D printing of robotic soft actuators with programmable bioinspired architectures
Schaffner, M., Faber, J. A., Pianegonda, L., Rühs, P. A., Coulter, F., & Studart, A. R. (2018) · Nature Communications · doi:10.1038/s41467-018-03216-w · Cited by 518
3D-printed bioceramic scaffolds: From bone tissue engineering to tumor therapy.
Ma, H., Feng, C., Chang, J., & Wu, C. (2018) · Acta Biomaterialia · doi:10.1016/j.actbio.2018.08.026 · Cited by 512
Four-dimensional printing of liquid crystal elastomers
Ambulo, C. P., Burroughs, J. J., Boothby, J. M., Kim, H., Shankar, M. R., & Ware, T. H. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b11851 · Cited by 508
Direct writing in three dimensions
Lewis, J. A., & Gratson, G. M. (2004) · Materials Today · doi:10.1016/s1369-7021(04)00344-x · Cited by 507
3D Printing of Emulsions and Foams into Hierarchical Porous Ceramics
Minas, C., Carnelli, D., Tervoort, E., & Studart, A. R. (2016) · Advanced Materials · doi:10.1002/adma.201603390 · Cited by 507
Wei, H., Zhang, Q., Yao, Y., Liu, L., Liu, Y., & Leng, J. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.6b12824 · Cited by 504
Efficient 3D Printed Pseudocapacitive Electrodes with Ultrahigh MnO2 Loading
Yao, B., Chandrasekaran, S., Zhang, J., Xiao, W., Qian, F., Zhu, C., Duoss, E. B., Spadaccini, C. M., Worsley, M. A., & Li, Y. (2019) · Joule · doi:10.1016/j.joule.2018.09.020 · Cited by 491
Versatile N‐Doped MXene Ink for Printed Electrochemical Energy Storage Application
Yu, L., Fan, Z., Shao, Y., Tian, Z., Sun, J., & Liu, Z. (2019) · Advanced Energy Materials · doi:10.1002/aenm.201901839 · Cited by 487
High-resolution PLA-based composite scaffolds via 3-D printing technology
Serra, T., Planell, J. A., & Navarro, M. (2013) · Acta Biomaterialia · doi:10.1016/j.actbio.2012.10.041 · Cited by 479
Yang, F., Zhang, M., Bhandari, B., & Liu, Y. (2018) · LWT · doi:10.1016/j.lwt.2017.08.054 · Cited by 479
Investigation on fish surimi gel as promising food material for 3D printing
Wang, L., Zhang, M., Bhandari, B., & Yang, C. (2018) · Journal of Food Engineering · doi:10.1016/j.jfoodeng.2017.02.029 · Cited by 476
Progress in 3D Printing of Carbon Materials for Energy‐Related Applications
Fu, K., Yao, Y., Dai, J., & Hu, L. (2017) · Advanced Materials · doi:10.1002/adma.201603486 · Cited by 475
Linking Rheology and Printability for Dense and Strong Ceramics by Direct Ink Writing
M’Barki, A., Bocquet, L., & Stevenson, A. (2017) · Scientific Reports · doi:10.1038/s41598-017-06115-0 · Cited by 471
3D Printing of Freestanding MXene Architectures for Current‐Collector‐Free Supercapacitors
Yang, W., Yang, J., Byun, J. J., Moissinac, F. P., Xu, J., Haigh, S. J., Domingos, M., Bissett, M. A., Dryfe, R. A. W., & Barg, S. (2019) · Advanced Materials · doi:10.1002/adma.201902725 · Cited by 460
Additive manufacturing for the food industry
Lipton, J. I., Cutler, M., Nigl, F., Cohen, D., & Lipson, H. (2015) · Trends in Food Science & Technology · doi:10.1016/j.tifs.2015.02.004 · Cited by 459
3D Printed Stretchable Tactile Sensors
Guo, S., Qiu, K., Meng, F., Park, S. H., & McAlpine, M. C. (2017) · Advanced Materials · doi:10.1002/adma.201701218 · Cited by 445
Orangi, J., Hamade, F., Davis, V. A., & Beidaghi, M. (2020) · ACS Nano · doi:10.1021/acsnano.9b07325 · Cited by 443
4D Printing of Hydrogels: A Review
Champeau, M., Heinze, D. A., Viana, T. N., de Souza, E. R., Chinellato, A. C., & Titotto, S. (2020) · Advanced Functional Materials · doi:10.1002/adfm.201910606 · Cited by 443
3D Printing PDMS Elastomer in a Hydrophilic Support Bath via Freeform Reversible Embedding
Hinton, T. J., Hudson, A., Pusch, K., Lee, A., & Feinberg, A. W. (2016) · ACS Biomaterials Science & Engineering · doi:10.1021/acsbiomaterials.6b00170 · Cited by 437
3D Printing of Customized Li‐Ion Batteries with Thick Electrodes
Wei, T., Ahn, B. Y., Grotto, J., & Lewis, J. A. (2018) · Advanced Materials · doi:10.1002/adma.201703027 · Cited by 434
Current advances and future perspectives of 3D printing natural-derived biopolymers
Liu, J., Sun, L., Xu, W., Wang, Q., Yu, S., & Sun, J. (2019) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2018.11.077 · Cited by 428
3D printing of bacteria into functional complex materials
Schaffner, M., Rühs, P. A., Coulter, F., Kilcher, S., & Studart, A. R. (2017) · Science Advances · doi:10.1126/sciadv.aao6804 · Cited by 425
Rapid Continuous Multimaterial Extrusion Bioprinting
Liu, W., Zhang, Y. S., Heinrich, M. A., De Ferrari, F., Jang, H. L., Bakht, S. M., Alvarez, M. M., Yang, J., Li, Y., Trujillo‐de Santiago, G., et al. (2017) · Advanced Materials · doi:10.1002/adma.201604630 · Cited by 424
Liu, Z., Wu, Z., Yang, S., Dong, R., Feng, X., & Müllen, K. (2016) · Advanced Materials · doi:10.1002/adma.201505304 · Cited by 411
All‐Printed Flexible and Stretchable Electronics
Mohammed, M. G., & Kramer, R. (2017) · Advanced Materials · doi:10.1002/adma.201604965 · Cited by 410
A Review on 3D Printing for Customized Food Fabrication
Sun, J., Peng, Z., Zhou, W., Fuh, J. Y. H., Hong, G. S., & Chiu, A. (2015) · Procedia Manufacturing · doi:10.1016/j.promfg.2015.09.057 · Cited by 407
Postiglione, G., Natale, G., Griffini, G., Levi, M., & Turri, S. (2015) · Composites Part A: Applied Science and Manufacturing · doi:10.1016/j.compositesa.2015.05.014 · Cited by 399
3D Printing of Multifunctional Hydrogels
Chen, Z., Zhao, D., Liu, B., Nian, G., Li, X., Yin, J., Qu, S., & Yang, W. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201900971 · Cited by 398
3D Printing of Living Responsive Materials and Devices
Liu, X., Yuk, H., Lin, S., Parada, G. A., Tang, T., Tham, E., de la Fuente‐Nunez, C., Lu, T. K., & Zhao, X. (2018) · Advanced Materials · doi:10.1002/adma.201704821 · Cited by 393
Directed Colloidal Assembly of 3D Periodic Structures
Smay, J. E., Gratson, G. M., Shepherd, R. F., Cesarano, J., & Lewis, J. A. (2002) · Advanced Materials · doi:10.1002/1521-4095(20020916)14:18<1279::aid-adma1279>3.0.co;2-a · Cited by 388
Synthesis and biomedical applications of aerogels: Possibilities and challenges
Maleki, H., Durães, L., García-González, C. A., del Gaudio, P., Portugal, A., & Mahmoudi, M. (2016) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2016.05.011 · Cited by 386
Molecularly-engineered, 4D-printed liquid crystal elastomer actuators
Saed, M. O., Ambulo, C. P., Kim, H., De, R., Raval, V., Searles, K., Siddiqui, D. A., Cue, J. M. O., Stefan, M. C., Shankar, M. R., et al. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201806412 · Cited by 383
A New 3D Printing Strategy by Harnessing Deformation, Instability, and Fracture of Viscoelastic Inks
Yuk, H., & Zhao, X. (2018) · Advanced Materials · doi:10.1002/adma.201704028 · Cited by 381
Robocasting of structural ceramic parts with hydrogel inks
Feilden, E., Blanca, E. G.-T., Giuliani, F., Saiz, E., & Vandeperre, L. (2016) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2016.03.001 · Cited by 378
Direct 3D Printing of Ultralight Graphene Oxide Aerogel Microlattices
Jiang, Y., Xu, Z., Huang, T., Liu, Y., Guo, F., Xi, J., Gao, W., & Gao, C. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201707024 · Cited by 370
Biomimetic 3D tissue printing for soft tissue regeneration
Pati, F., Ha, D.-H., Jang, J., Han, H. H., Rhie, J.-W., & Cho, D.-W. (2015) · Biomaterials · doi:10.1016/j.biomaterials.2015.05.043 · Cited by 368
Graphene oxide dispersions: tuning rheology to enable fabrication
Naficy, S., Jalili, R., Aboutalebi, S. H., Gorkin III, R. A., Konstantinov, K., Innis, P. C., Spinks, G. M., Poulin, P., & Wallace, G. G. (2014) · Mater. Horiz. · doi:10.1039/c3mh00144j · Cited by 368
High-resolution, reconfigurable printing of liquid metals with three-dimensional structures
Park, Y.-G., An, H. S., Kim, J.-Y., & Park, J.-U. (2019) · Science Advances · doi:10.1126/sciadv.aaw2844 · Cited by 367
Fu, Q., Saiz, E., & Tomsia, A. P. (2011) · Acta Biomaterialia · doi:10.1016/j.actbio.2011.06.030 · Cited by 366
Structuring adsorbents and catalysts by processing of porous powders
Akhtar, F., Andersson, L., Ogunwumi, S., Hedin, N., & Bergström, L. (2014) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2014.01.008 · Cited by 363
Effects of interlocking on interlayer adhesion and strength of structures in 3D printing of concrete
Zareiyan, B., & Khoshnevis, B. (2017) · Automation in Construction · doi:10.1016/j.autcon.2017.08.019 · Cited by 353
Zhu, Z., Ng, D. W. H., Park, H. S., & McAlpine, M. C. (2020) · Nature Reviews Materials · doi:10.1038/s41578-020-00235-2 · Cited by 348
Engineering an in vitro air-blood barrier by 3D bioprinting
Horváth, L., Umehara, Y., Jud, C., Blank, F., Petri-Fink, A., & Rothen-Rutishauser, B. (2015) · Scientific Reports · doi:10.1038/srep07974 · Cited by 345
Microfluidic Printheads for Multimaterial 3D Printing of Viscoelastic Inks
Hardin, J. O., Ober, T. J., Valentine, A. D., & Lewis, J. A. (2015) · Advanced Materials · doi:10.1002/adma.201500222 · Cited by 340
Direct Ink Writing Based 4D Printing of Materials and Their Applications
Wan, X., Luo, L., Liu, Y., & Leng, J. (2020) · Advanced Science · doi:10.1002/advs.202001000 · Cited by 337
Sequential self-folding of polymer sheets
Liu, Y., Shaw, B., Dickey, M. D., & Genzer, J. (2017) · Science Advances · doi:10.1126/sciadv.1602417 · Cited by 335
Extrusion‐Based 3D Printing of Hierarchically Porous Advanced Battery Electrodes
Lacey, S. D., Kirsch, D. J., Li, Y., Morgenstern, J. T., Zarket, B. C., Yao, Y., Dai, J., Garcia, L. Q., Liu, B., Gao, T., et al. (2018) · Advanced Materials · doi:10.1002/adma.201705651 · Cited by 332
Liquid Metal Direct Write and 3D Printing: A Review
Neumann, T. V., & Dickey, M. D. (2020) · Advanced Materials Technologies · doi:10.1002/admt.202000070 · Cited by 332
Direct ink writing advances in multi-material structures for a sustainable future
Rocha, V. G., Saiz, E., Tirichenko, I. S., & García-Tuñón, E. (2020) · Journal of Materials Chemistry A · doi:10.1039/d0ta04181e · Cited by 327
Roach, D. J., Yuan, C., Kuang, X., Li, V. C.-F., Blake, P., Romero, M. L., Hammel, I., Yu, K., & Qi, H. J. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b04401 · Cited by 319
Laser-assisted direct ink writing of planar and 3D metal architectures
Skylar-Scott, M. A., Gunasekaran, S., & Lewis, J. A. (2016) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1525131113 · Cited by 318
Lewicki, J. P., Rodriguez, J. N., Zhu, C., Worsley, M. A., Wu, A. S., Kanarska, Y., Horn, J. D., Duoss, E. B., Ortega, J. M., Elmer, W., et al. (2017) · Scientific Reports · doi:10.1038/srep43401 · Cited by 318
Zhang, J., Zhao, S., Zhu, M., Zhu, Y., Zhang, Y., Liu, Z., & Zhang, C. (2014) · J. Mater. Chem. B · doi:10.1039/c4tb01063a · Cited by 317
Three‐Dimensional Printing of Elastomeric, Cellular Architectures with Negative Stiffness
Duoss, E. B., Weisgraber, T. H., Hearon, K., Zhu, C., Small, W., Metz, T. R., Vericella, J. J., Barth, H. D., Kuntz, J. D., Maxwell, R. S., et al. (2014) · Advanced Functional Materials · doi:10.1002/adfm.201400451 · Cited by 316
Direct-Ink-Write 3D Printing of Hydrogels into Biomimetic Soft Robots
Cheng, Y., Chan, K. H., Wang, X.-Q., Ding, T., Li, T., Lu, X., & Ho, G. W. (2019) · ACS Nano · doi:10.1021/acsnano.9b06144 · Cited by 312
Active mixing of complex fluids at the microscale
Ober, T. J., Foresti, D., & Lewis, J. A. (2015) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1509224112 · Cited by 306
3D Printed Stem‐Cell Derived Neural Progenitors Generate Spinal Cord Scaffolds
Joung, D., Truong, V., Neitzke, C. C., Guo, S., Walsh, P. J., Monat, J. R., Meng, F., Park, S. H., Dutton, J. R., Parr, A. M., et al. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201801850 · Cited by 306
Yao, B., Chandrasekaran, S., Zhang, H., Ma, A., Kang, J., Zhang, L., Lu, X., Qian, F., Zhu, C., Duoss, E. B., et al. (2020) · Advanced Materials · doi:10.1002/adma.201906652 · Cited by 305
Sintering and robocasting of β-tricalcium phosphate scaffolds for orthopaedic applications
Miranda, P., Saiz, E., Gryn, K., & Tomsia, A. P. (2006) · Acta Biomaterialia · doi:10.1016/j.actbio.2006.02.004 · Cited by 304
Mechanical properties of calcium phosphate scaffolds fabricated by robocasting
Miranda, P., Pajares, A., Saiz, E., Tomsia, A. P., & Guiberteau, F. (2008) · Journal of Biomedical Materials Research Part A · doi:10.1002/jbm.a.31587 · Cited by 301
Rotational 3D printing of damage-tolerant composites with programmable mechanics
Raney, J. R., Compton, B. G., Mueller, J., Ober, T. J., Shea, K., & Lewis, J. A. (2018) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1715157115 · Cited by 301
Feasibility study of hydrocolloid incorporated 3D printed pork as dysphagia food
Dick, A., Bhandari, B., Dong, X., & Prakash, S. (2020) · Food Hydrocolloids · doi:10.1016/j.foodhyd.2020.105940 · Cited by 301
3D printed reversible shape changing soft actuators assisted by liquid crystal elastomers
Yuan, C., Roach, D. J., Dunn, C. K., Mu, Q., Kuang, X., Yakacki, C. M., Wang, T. J., Yu, K., & Qi, H. J. (2017) · Soft Matter · doi:10.1039/c7sm00759k · Cited by 300
Direct‐Write Assembly of 3D Hydrogel Scaffolds for Guided Cell Growth
Barry, R. A., Shepherd, R. F., Hanson, J. N., Nuzzo, R. G., Wiltzius, P., & Lewis, J. A. (2009) · Advanced Materials · doi:10.1002/adma.200803702 · Cited by 295
Liquid-Phase Gallium–Indium Alloy Electronics with Microcontact Printing
Tabatabai, A., Fassler, A., Usiak, C., & Majidi, C. (2013) · Langmuir · doi:10.1021/la401245d · Cited by 293
Generalized 3D Printing of Graphene-Based Mixed-Dimensional Hybrid Aerogels
Tang, X., Zhou, H., Cai, Z., Cheng, D., He, P., Xie, P., Zhang, D., & Fan, T. (2018) · ACS Nano · doi:10.1021/acsnano.8b00304 · Cited by 290
A multifunctional skin-like sensor based on a 3D printed thermo-responsive hydrogel
Lei, Z., Wang, Q., & Wu, P. (2017) · Materials Horizons · doi:10.1039/c7mh00262a · Cited by 288
Direct‐Write Assembly of Microperiodic Silk Fibroin Scaffolds for Tissue Engineering Applications
Ghosh, S., Parker, S. T., Wang, X., Kaplan, D. L., & Lewis, J. A. (2008) · Advanced Functional Materials · doi:10.1002/adfm.200800040 · Cited by 287
Zhong, M., Liu, Y.-T., & Xie, X.-M. (2015) · Journal of Materials Chemistry B · doi:10.1039/c5tb00075k · Cited by 285
Dynamics of Cellulose Nanocrystal Alignment during 3D Printing
Hausmann, M. K., Rühs, P. A., Siqueira, G., Läuger, J., Libanori, R., Zimmermann, T., & Studart, A. R. (2018) · ACS Nano · doi:10.1021/acsnano.8b02366 · Cited by 282
Direct ink writing of energy materials
Tagliaferri, S., Panagiotopoulos, A., & Mattevi, C. (2021) · Materials Advances · doi:10.1039/d0ma00753f · Cited by 281
Three-dimensional printing of functionally graded liquid crystal elastomer
Wang, Z., Wang, Z., Zheng, Y., He, Q., Wang, Y., & Cai, S. (2020) · Science Advances · doi:10.1126/sciadv.abc0034 · Cited by 274
Nguyen, D. T., Meyers, C., Yee, T. D., Dudukovic, N. A., Destino, J. F., Zhu, C., Duoss, E. B., Baumann, T. F., Suratwala, T., Smay, J. E., et al. (2017) · Advanced Materials · doi:10.1002/adma.201701181 · Cited by 273
Origami and 4D printing of elastomer-derived ceramic structures
Liu, G., Zhao, Y., Wu, G., & Lu, J. (2018) · Science Advances · doi:10.1126/sciadv.aat0641 · Cited by 270
Direct Ink Write (DIW) 3D Printed Cellulose Nanocrystal Aerogel Structures
Li, V. C.-F., Dunn, C. K., Zhang, Z., Deng, Y., & Qi, H. J. (2017) · Scientific Reports · doi:10.1038/s41598-017-07771-y · Cited by 269
Yu, Y., Zhang, Y., Martin, J. A., & Ozbolat, I. T. (2013) · Journal of Biomechanical Engineering · doi:10.1115/1.4024575 · Cited by 267
Concentrated hydroxyapatite inks for direct-write assembly of 3-D periodic scaffolds
Michna, S., Wu, W., & Lewis, J. A. (2005) · Biomaterials · doi:10.1016/j.biomaterials.2005.02.040 · Cited by 266
Material characterisation and process development for chocolate additive layer manufacturing
Hao, L., Mellor, S., Seaman, O., Henderson, J., Sewell, N., & Sloan, M. (2010) · Virtual and Physical Prototyping · doi:10.1080/17452751003753212 · Cited by 252
Bioinspired Strong and Highly Porous Glass Scaffolds
Fu, Q., Saiz, E., & Tomsia, A. P. (2011) · Advanced Functional Materials · doi:10.1002/adfm.201002030 · Cited by 252
Additive Manufacturing of Dense Ceramic Parts via Direct Ink Writing of Aqueous Alumina Suspensions
Rueschhoff, L., Costakis, W., Michie, M., Youngblood, J., & Trice, R. (2016) · International Journal of Applied Ceramic Technology · doi:10.1111/ijac.12557 · Cited by 251
Zhu, S., Stieger, M. A., van der Goot, A. J., & Schutyser, M. A. I. (2019) · Innovative Food Science & Emerging Technologies · doi:10.1016/j.ifset.2019.102214 · Cited by 250
3D food printing of as the new way of preparing food: A review
Mantihal, S., Kobun, R., & Lee, B.-B. (2020) · International Journal of Gastronomy and Food Science · doi:10.1016/j.ijgfs.2020.100260 · Cited by 250
O'Mahony, A. M., Williams, J. L., & Spencer, P. (2001) · Clinical Oral Implants Research · doi:10.1034/j.1600-0501.2001.120614.x · Cited by 248
Wang, Z., Guan, X., Huang, H., Wang, H., Lin, W., & Peng, Z. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201807569 · Cited by 247
3D Printed Functional and Biological Materials on Moving Freeform Surfaces
Zhu, Z., Guo, S., Hirdler, T., Eide, C., Fan, X., Tolar, J., & McAlpine, M. C. (2018) · Advanced Materials · doi:10.1002/adma.201707495 · Cited by 245
Three-dimensional ultraflexible triboelectric nanogenerator made by 3D printing
Chen, B., Tang, W., Jiang, T., Zhu, L., Chen, X., He, C., Xu, L., Guo, H., Lin, P., Li, D., et al. (2018) · Nano Energy · doi:10.1016/j.nanoen.2017.12.049 · Cited by 243
Architected cellular ceramics with tailored stiffness via direct foam writing
Muth, J. T., Dixon, P. G., Woish, L., Gibson, L. J., & Lewis, J. A. (2017) · Proceedings of the National Academy of Sciences · doi:10.1073/pnas.1616769114 · Cited by 242
Corker, A., Ng, H. C.-H., Poole, R. J., & García-Tuñón, E. (2019) · Soft Matter · doi:10.1039/c8sm01936c · Cited by 242
Shakor, P., Sanjayan, J., Nazari, A., & Nejadi, S. (2017) · Construction and Building Materials · doi:10.1016/j.conbuildmat.2017.02.037 · Cited by 229
Liu, X., Rahaman, M. N., Hilmas, G. E., & Bal, B. S. (2013) · Acta Biomaterialia · doi:10.1016/j.actbio.2013.02.026 · Cited by 223
Development and characterisation of a new bioink for additive tissue manufacturing
Melchels, F. P. W., Dhert, W. J. A., Hutmacher, D. W., & Malda, J. (2014) · Journal of Materials Chemistry B · doi:10.1039/c3tb21280g · Cited by 222
Gonçalves, E. M., Oliveira, F. J., Silva, R. F., Neto, M. A., Fernandes, M. H., Amaral, M., Vallet‐Regí, M., & Vila, M. (2016) · Journal of Biomedical Materials Research Part B: Applied Biomaterials · doi:10.1002/jbm.b.33432 · Cited by 221
Rodriguez, M. J., Brown, J., Giordano, J., Lin, S. J., Omenetto, F. G., & Kaplan, D. L. (2017) · Biomaterials · doi:10.1016/j.biomaterials.2016.11.046 · Cited by 220
Chen, S., Huang, T., Zuo, H., Qian, S., Guo, Y., Sun, L., Lei, D., Wu, Q., Zhu, B., He, C., et al. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201805108 · Cited by 219
Blake, A. J., Kohlmeyer, R. R., Hardin, J. O., Carmona, E. A., Maruyama, B., Berrigan, J. D., Huang, H., & Durstock, M. F. (2017) · Advanced Energy Materials · doi:10.1002/aenm.201602920 · Cited by 217
Architected Lattices with High Stiffness and Toughness via Multicore–Shell 3D Printing
Mueller, J., Raney, J. R., Shea, K., & Lewis, J. A. (2018) · Advanced Materials · doi:10.1002/adma.201705001 · Cited by 216
Liu, Z., Zhang, M., & Bhandari, B. (2018) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2018.06.048 · Cited by 215
Elevated‐Temperature 3D Printing of Hybrid Solid‐State Electrolyte for Li‐Ion Batteries
Cheng, M., Jiang, Y., Yao, W., Yuan, Y., Deivanayagam, R., Foroozan, T., Huang, Z., Song, B., Rojaee, R., Shokuhfar, T., et al. (2018) · Advanced Materials · doi:10.1002/adma.201800615 · Cited by 214
3D Printing of Materials with Tunable Failure via Bioinspired Mechanical Gradients
Kokkinis, D., Bouville, F., & Studart, A. R. (2018) · Advanced Materials · doi:10.1002/adma.201705808 · Cited by 212
Toward digitally controlled catalyst architectures: Hierarchical nanoporous gold via 3D printing
Zhu, C., Qi, Z., Beck, V. A., Luneau, M., Lattimer, J., Chen, W., Worsley, M. A., Ye, J., Duoss, E. B., Spadaccini, C. M., et al. (2018) · Science Advances · doi:10.1126/sciadv.aas9459 · Cited by 212
Ultraviolet‐Assisted Direct‐Write Fabrication of Carbon Nanotube/Polymer Nanocomposite Microcoils
Lebel, L. L., Aïssa, B., Khakani, M. A. E., & Therriault, D. (2009) · Advanced Materials · doi:10.1002/adma.200902192 · Cited by 209
Metallic Architectures from 3D‐Printed Powder‐Based Liquid Inks
Jakus, A. E., Taylor, S. L., Geisendorfer, N. R., Dunand, D. C., & Shah, R. N. (2015) · Advanced Functional Materials · doi:10.1002/adfm.201503921 · Cited by 209
Zhang, H., Mao, X., Du, Z., Jiang, W., Han, X., Zhao, D., Han, D., & Li, Q. (2016) · Science and Technology of Advanced Materials · doi:10.1080/14686996.2016.1145532 · Cited by 208
3D Printing Bioinspired Ceramic Composites
Feilden, E., Ferraro, C., Zhang, Q., García-Tuñón, E., D’Elia, E., Giuliani, F., Vandeperre, L., & Saiz, E. (2017) · Scientific Reports · doi:10.1038/s41598-017-14236-9 · Cited by 208
Novel ink for ambient condition printing of liquid crystal elastomers for 4D printing
Roach, D. J., Kuang, X., Yuan, C., Chen, K., & Qi, H. J. (2018) · Smart Materials and Structures · doi:10.1088/1361-665x/aae96f · Cited by 208
Fabrication of tough epoxy with shape memory effects by UV-assisted direct-ink write printing
Chen, K., Kuang, X., Li, V., Kang, G., & Qi, H. J. (2018) · Soft Matter · doi:10.1039/c7sm02362f · Cited by 207
A Versatile Approach for Direct Patterning of Liquid Metal Using Magnetic Field
Ma, B., Xu, C., Chi, J., Chen, J., Zhao, C., & Liu, H. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201901370 · Cited by 204
Solvent‐Cast Three‐Dimensional Printing of Multifunctional Microsystems
Guo, S., Gosselin, F., Guerin, N., Lanouette, A., Heuzey, M., & Therriault, D. (2013) · Small · doi:10.1002/smll.201300975 · Cited by 203
3D printing of cereal-based food structures containing probiotics
Zhang, L., Lou, Y., & Schutyser, M. A. I. (2018) · Food Structure · doi:10.1016/j.foostr.2018.10.002 · Cited by 203
3D Printed Multifunctional, Hyperelastic Silicone Rubber Foam
Chen, Q., Zhao, J., Ren, J., Rong, L., Cao, P., & Advincula, R. C. (2019) · Advanced Functional Materials · doi:10.1002/adfm.201900469 · Cited by 201
Park, Y.-G., Min, H., Kim, H., Zhexembekova, A., Lee, C. Y., & Park, J.-U. (2019) · Nano Letters · doi:10.1021/acs.nanolett.9b00150 · Cited by 200
Mechanically Robust, Ultraelastic Hierarchical Foam with Tunable Properties via 3D Printing
Chen, Q., Cao, P., & Advincula, R. C. (2018) · Advanced Functional Materials · doi:10.1002/adfm.201800631 · Cited by 197
3D printing of multi-scalable structures via high penetration near-infrared photopolymerization
Zhu, J., Zhang, Q., Yang, T., Liu, Y., & Liu, R. (2020) · Nature Communications · doi:10.1038/s41467-020-17251-z · Cited by 195
Fujieda, T., Shiratori, H., Kuwabara, K., Kato, T., Yamanaka, K., Koizumi, Y., & Chiba, A. (2015) · Materials Letters · doi:10.1016/j.matlet.2015.06.046 · Cited by 194
Rocha, V. G., García-Tuñón, E., Botas, C., Markoulidis, F., Feilden, E., D’Elia, E., Ni, N., Shaffer, M., & Saiz, E. (2017) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.7b10285 · Cited by 191
Costakis, W. J., Rueschhoff, L. M., Diaz-Cano, A. I., Youngblood, J. P., & Trice, R. W. (2016) · Journal of the European Ceramic Society · doi:10.1016/j.jeurceramsoc.2016.06.002 · Cited by 187
3D Printing of Dual-Physical Cross-linking Hydrogel with Ultrahigh Strength and Toughness
Jiang, P., Lin, P., Yang, C., Qin, H., Wang, X., & Zhou, F. (2020) · Chemistry of Materials · doi:10.1021/acs.chemmater.0c02941 · Cited by 187
Additive Manufacturing and Performance of Architectured Cement‐Based Materials
Moini, M., Olek, J., Youngblood, J. P., Magee, B., & Zavattieri, P. D. (2018) · Advanced Materials · doi:10.1002/adma.201802123 · Cited by 184
Christ, J. F., Aliheidari, N., Pötschke, P., & Ameli, A. (2018) · Polymers · doi:10.3390/polym11010011 · Cited by 184
3D ink-extrusion additive manufacturing of CoCrFeNi high-entropy alloy micro-lattices
Kenel, C., Casati, N. P. M., & Dunand, D. C. (2019) · Nature Communications · doi:10.1038/s41467-019-08763-4 · Cited by 183
Azam, R. S. M., Zhang, M., Bhandari, B., & Yang, C. (2018) · Food Biophysics · doi:10.1007/s11483-018-9531-x · Cited by 182
Wei, H., Cauchy, X., Navas, I. O., Abderrafai, Y., Chizari, K., Sundararaj, U., Liu, Y., Leng, J., & Therriault, D. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b04245 · Cited by 182
Structural optimization of 3D-printed synthetic spider webs for high strength
Qin, Z., Compton, B. G., Lewis, J. A., & Buehler, M. J. (2015) · Nature Communications · doi:10.1038/ncomms8038 · Cited by 179
High-strength epoxy nanocomposites for 3D printing
Hmeidat, N. S., Kemp, J. W., & Compton, B. G. (2018) · Composites Science and Technology · doi:10.1016/j.compscitech.2018.03.008 · Cited by 177
Ahn, B. Y., Shoji, D., Hansen, C. J., Hong, E., Dunand, D. C., & Lewis, J. A. (2010) · Advanced Materials · doi:10.1002/adma.200904232 · Cited by 176
4D Printing of a Liquid Crystal Elastomer with a Controllable Orientation Gradient
Zhang, C., Lu, X., Fei, G., Wang, Z., Xia, H., & Zhao, Y. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.9b18037 · Cited by 176
3D food printing: a categorised review of inks and their development
Voon, S. L., An, J., Wong, G., Zhang, Y., & Chua, C. K. (2019) · Virtual and Physical Prototyping · doi:10.1080/17452759.2019.1603508 · Cited by 175
Recent Progress of Direct Ink Writing of Electronic Components for Advanced Wearable Devices
Zhang, Y., Shi, G., Qin, J., Lowe, S. E., Zhang, S., Zhao, H., & Zhong, Y. L. (2019) · ACS Applied Electronic Materials · doi:10.1021/acsaelm.9b00428 · Cited by 175
High‐Throughput Printing via Microvascular Multinozzle Arrays
Hansen, C. J., Saksena, R., Kolesky, D. B., Vericella, J. J., Kranz, S. J., Muldowney, G. P., Christensen, K. T., & Lewis, J. A. (2013) · Advanced Materials · doi:10.1002/adma.201203321 · Cited by 170
Direct Ink Writing Technology (3D Printing) of Graphene-Based Ceramic Nanocomposites: A Review
Solís Pinargote, N. W., Smirnov, A., Peretyagin, N., Seleznev, A., & Peretyagin, P. (2020) · Nanomaterials · doi:10.3390/nano10071300 · Cited by 168
Brown, E., Yan, P., Tekik, H., Elangovan, A., Wang, J., Lin, D., & Li, J. (2019) · Materials & Design · doi:10.1016/j.matdes.2019.107689 · Cited by 165
Dual-Gel 4D Printing of Bioinspired Tubes
Liu, J., Erol, O., Pantula, A., Liu, W., Jiang, Z., Kobayashi, K., Chatterjee, D., Hibino, N., Romer, L. H., Kang, S. H., et al. (2019) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.8b17218 · Cited by 161
4D Printing of Robust Hydrogels Consisted of Agarose Nanofibers and Polyacrylamide
Guo, J., Zhang, R., Zhang, L., & Cao, X. (2018) · ACS Macro Letters · doi:10.1021/acsmacrolett.7b00957 · Cited by 159
Direct coherent multi-ink printing of fabric supercapacitors
Zhao, J., Lu, H., Zhang, Y., Yu, S. Y., Malyi, O. I., Zhao, X., Wang, H., Wang, H., Peng, J., Li, X., et al. (2021) · Science Advances · doi:10.1126/sciadv.abd6978 · Cited by 153
Kim, H. W., Lee, I. J., Park, S. M., Lee, J. H., Nguyen, M.-H., & Park, H. J. (2018) · LWT · doi:10.1016/j.lwt.2018.11.019 · Cited by 150
3D printing of a multifunctional nanocomposite helical liquid sensor
Guo, S., Yang, X., Heuzey, M.-C., & Therriault, D. (2015) · Nanoscale · doi:10.1039/c5nr00278h · Cited by 147
Li, V. C. F., Mulyadi, A., Dunn, C. K., Deng, Y., & Qi, H. J. (2017) · ACS Sustainable Chemistry & Engineering · doi:10.1021/acssuschemeng.7b03439 · Cited by 147
Research works printed but not linked: 81
- 10.1080/10667857.1997.11752736 · doi:10.1080/10667857.1997.11752736
- 10.1016/j.eml.2016.04.003 · doi:10.1016/j.eml.2016.04.003
- 10.1016/j.mtcomm.2021.102037 · doi:10.1016/j.mtcomm.2021.102037
- 10.1021/acs.chemmater.9b02961 · doi:10.1021/acs.chemmater.9b02961
- 10.1007/s00170-008-1700-5 · doi:10.1007/s00170-008-1700-5
- 10.1002/mame.201800511 · doi:10.1002/mame.201800511
- 10.1002/adem.201801314 · doi:10.1002/adem.201801314
- 10.1021/acsami.0c18255 · doi:10.1021/acsami.0c18255
- 10.1126/sciadv.abj8780 · doi:10.1126/sciadv.abj8780
- 10.1016/j.polymer.2011.01.059 · doi:10.1016/j.polymer.2011.01.059
- 10.1021/acsami.8b14584 · doi:10.1021/acsami.8b14584
- 10.1002/adma.201904668 · doi:10.1002/adma.201904668
- 10.1177/0021998319865019 · doi:10.1177/0021998319865019
- 10.1088/1748-3190/aa6028 · doi:10.1088/1748-3190/aa6028
- 10.1007/s11837-017-2707-x · doi:10.1007/s11837-017-2707-x
- 10.1021/acs.langmuir.9b00766 · doi:10.1021/acs.langmuir.9b00766
- 10.1088/0954-0083/9/4/008 · doi:10.1088/0954-0083/9/4/008
- 10.1016/S1359-835X(98)00110-9 · doi:10.1016/s1359-835x(98)00110-9
- 10.1007/s11340-019-00498-z · doi:10.1007/s11340-019-00498-z
- 10.1016/j.addma.2020.101109 · doi:10.1016/j.addma.2020.101109
- A.Khater S.Bhattacharyya M. A. S. R.Saadi M.Barnes M.Lou V.Harikrishnan S. M.Sajadi P. J.Boul C. S.Tiwary H.Zhu M. M.Rahman P. M.Ajayan arXiv:2103.02672 [cond‐mat physics:physics]2021. · arXiv
- 10.1016/j.foodhyd.2008.01.001 · doi:10.1016/j.foodhyd.2008.01.001
- D.Periard N.Schaal M.Schaal E.Malone H.Lipson in2007 International Solid Freeform Fabrication Symposium 2007.
- 10.1038/s41538-021-00107-1 · DOI
- 10.1016/B978-0-12-385469-8.00047-2 · doi:10.1016/b978-0-12-385469-8.00047-2
- 10.1002/adem.201900604 · doi:10.1002/adem.201900604
- 10.1016/j.matdes.2015.02.018 · doi:10.1016/j.matdes.2015.02.018
- 10.1002/adem.201901541 · doi:10.1002/adem.201901541
- 10.1021/acssuschemeng.7b02450 · doi:10.1021/acssuschemeng.7b02450
- 10.1177/0022034517734846 · doi:10.1177/0022034517734846
- 10.1111/j.1551-2916.2012.05276.x · doi:10.1111/j.1551-2916.2012.05276.x
- 10.1111/ijac.12633 · doi:10.1111/ijac.12633
- 10.1016/j.addma.2019.05.018 · doi:10.1016/j.addma.2019.05.018
- 10.1111/jace.17911 · doi:10.1111/jace.17911
- 10.1002/jbm.a.31329 · doi:10.1002/jbm.a.31329
- 10.1111/jace.14213 · doi:10.1111/jace.14213
- 10.1002/adem.201800900 · doi:10.1002/adem.201800900
- 10.1016/j.jeurceramsoc.2017.05.021 · doi:10.1016/j.jeurceramsoc.2017.05.021
- 10.1038/s41467-019-09398-1 · doi:10.1038/s41467-019-09398-1
- 10.1016/j.matdes.2008.04.056 · doi:10.1016/j.matdes.2008.04.056
- 10.1016/j.compstruct.2016.01.020 · doi:10.1016/j.compstruct.2016.01.020
- 10.1016/j.jnucmat.2016.09.007 · doi:10.1016/j.jnucmat.2016.09.007
- 10.1080/17436753.2017.1379586 · doi:10.1080/17436753.2017.1379586
- Thomas D. J., 2017, Am. Ceram. Soc. Bull., 96, 28
- 10.1111/jace.14145 · doi:10.1111/jace.14145
- Singh M., 2015, Ceramic Engineering and Science Proceedings, 145
- 10.1111/jace.15045 · doi:10.1111/jace.15045
- 10.3390/ma11040515 · doi:10.3390/ma11040515
- 10.1016/j.jeurceramsoc.2016.01.047 · doi:10.1016/j.jeurceramsoc.2016.01.047
- 10.3390/ma13071636 · doi:10.3390/ma13071636
- 10.1016/j.jeurceramsoc.2012.05.005 · doi:10.1016/j.jeurceramsoc.2012.05.005
- Moini M., 2019, RILEM Bookseries, 176
- 10.1002/adma.201705651 · DOI · Paper page
- 10.1002/ppsc.201600401 · doi:10.1002/ppsc.201600401
- 10.1122/1.3573828 · doi:10.1122/1.3573828
- 10.1016/j.carbon.2021.05.003 · doi:10.1016/j.carbon.2021.05.003
- Kenel C., 2020, Addit. Manuf., 37
- 10.1016/j.matdes.2018.09.024 · doi:10.1016/j.matdes.2018.09.024
- 10.1002/admi.201800571 · doi:10.1002/admi.201800571
- 10.1002/admt.201700351 · doi:10.1002/admt.201700351
- 10.1002/admt.201600047 · doi:10.1002/admt.201600047
- 10.1002/adem.201900397 · doi:10.1002/adem.201900397
- 10.1002/admt.201800379 · doi:10.1002/admt.201800379
- 10.1016/j.scriptamat.2019.02.016 · doi:10.1016/j.scriptamat.2019.02.016
- 10.1016/j.ceramint.2019.06.175 · doi:10.1016/j.ceramint.2019.06.175
- 10.1002/aenm.201800408 · doi:10.1002/aenm.201800408
- 10.1021/acsami.7b06804 · doi:10.1021/acsami.7b06804
- 10.1002/aelm.201700483 · doi:10.1002/aelm.201700483
- 10.1016/j.actamat.2009.01.019 · doi:10.1016/j.actamat.2009.01.019
- 10.3390/ma7054001 · doi:10.3390/ma7054001
- Y.Jiang Direct Ink Writing of Functional Fiber Composites Ph.D. Thesis University of Illinois at Chicago 2020.
- 10.1111/jace.17084 · doi:10.1111/jace.17084
- 10.1016/j.sna.2017.06.016 · doi:10.1016/j.sna.2017.06.016
- 10.1002/adma.201470235 · doi:10.1002/adma.201470235
- 10.1002/admt.201800299 · doi:10.1002/admt.201800299
- D.Cohen J.Lipton M.Cutler D.Coulter A.Vesco H.Lipson in2009 International Solid Freeform Fabrication Symposium University Of Texas At Austin2009.
- J.Lipton D.Arnold F.Nigl N.Lopez D.Cohen N.Noren H.Lipson in2010 International Solid Freeform Fabrication Symposium University Of Texas At Austin2010.
- 10.1088/1361-6463/abe503 · doi:10.1088/1361-6463/abe503
- 10.1016/j.cirpj.2017.07.001 · doi:10.1016/j.cirpj.2017.07.001
- 10.1016/j.matpr.2021.02.396 · doi:10.1016/j.matpr.2021.02.396
- 10.1007/s10404-010-0700-6 · doi:10.1007/s10404-010-0700-6
Cited by
Recent Advances in 3D Printing of Smart Scaffolds for Bone Tissue Engineering and Regeneration
Yuan, X., Zhu, W., Yang, Z., He, N., Chen, F., Han, X., & Zhou, K. (2024) · Advanced Materials · doi:10.1002/adma.202403641 · Cited by 339
Design and advanced manufacturing of electromagnetic interference shielding materials
Liu, J., Yu, M.-Y., Yu, Z.-Z., & Nicolosi, V. (2023) · Materials Today · doi:10.1016/j.mattod.2023.03.022 · Cited by 332
Parale, V. G., Kim, T., Choi, H., Phadtare, V. D., Dhavale, R. P., Kanamori, K., & Park, H. (2024) · Advanced Materials · doi:10.1002/adma.202307772 · Cited by 146
Abedini, A., Sohrabvandi, S., Sadighara, P., Hosseini, H., Farhoodi, M., Assadpour, E., Alizadeh Sani, M., Zhang, F., Seyyedi-Mansour, S., & Jafari, S. M. (2024) · Advances in Colloid and Interface Science · doi:10.1016/j.cis.2024.103181 · Cited by 71
Cheng, Y., Wang, Z., Lavorgna, M., He, L., & Xia, H. (2025) · Small · doi:10.1002/smll.202408869 · Cited by 20
Metadata
- Authors
- Saadi, M. A. S. R., Maguire, A., Pottackal, N. T., Thakur, M. S. H., Ikram, M. M., Hart, A. J., Ajayan, P. M., & Rahman, M. M.
- Venue
- Advanced Materials
- Publisher
- Wiley
- Published
- 2022-04-28
- Volume
- 34
- Issue
- 28
- Pages
- e2108855-e2108855
- ISSN
- 0935-9648 (ISSN-L)
- 1521-4095
- OpenAlex
- W4221095855
- Cited by
- 1,335
- References
- 290
- FWCI
- 71.70
- Type
- journal article
- Language
- en
- Open access
- closed
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.