The DOI matches its Crossref record; 101 of the 101 references it cites were found in a registry or an index; 38 of the 174 sources its claims cite were checked for support.
Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems
Open accessAbstract
This review examines fabrication strategies for nanocellulose-reinforced PLA, PCL, and their blends, highlighting processing strategies and property improvements.
Overview
CoChat Summary
TL;DR
This review critically examines nanocellulose (NC)-reinforced poly(lactic acid) (PLA), poly(ε-caprolactone) (PCL), and PLA/PCL blend bio-nanocomposites, focusing on fabrication, surface modification, dispersion, and property enhancement. It concludes that NC can improve mechanical, thermal, crystallization, and biodegradation performance—especially at low loadings—but industrial adoption is limited by cost, dispersion, compatibility, and scalability challenges.
Key findings
- NC incorporation generally enhances mechanical, thermal, crystallization, and biodegradation properties at low filler loadings, typically <5 wt.%; for PLA/CNCs from wood pulp at 0.5 wt.%, tensile strength increased from 57.9 to 79.6 MPa and crystallinity from 35.9 to 42.5%.
- In PCL systems, maximum Young’s modulus increase was about 77% at 12.5 wt.% CNCs from sugarcane bagasse; PCL/CNFs showed tensile strength increment of 7.5% at 10 wt.% and Young’s modulus increment of 76% at 15 wt.%; PCL/CNFs-g-PCL showed tensile strength enhanced by 45.5% at 30.0 wt.% loading.
- In PLA/PCL blends, NC can act as both reinforcement and compatibilizer; PLA/PCL/TOBC via 3D printing showed a 17.4% increase in tensile strength and 208% increase in elongation at break compared to neat PLA, with crystallinity around 60%.
- The review identifies NC production costs of ZAR 173.16 to ZAR 346.32 per kg versus commodity fillers like CaCO3 at less than ZAR 34.63 per kg, alongside dispersion, interface compatibility, and scalability as major barriers.
Methods
- Narrative/critical review of literature on NC-reinforced PLA, PCL, and PLA/PCL blend systems; no primary experimental data are reported.
- Covers NC extraction and characterization, surface modification, processing strategies (melt blending, solution casting, electrospinning, injection molding, extrusion, 3D printing), and dispersion techniques.
- Main analysis is a qualitative synthesis of reported structure–property relationships, including nucleation, compatibilization, mechanical reinforcement, thermal behavior, and biodegradation mechanisms.
Limitations
- The paper states barriers including high NC production cost, energy-intensive extraction and modification, dispersion difficulties in hydrophobic polymer matrices, industrial scalability, regulatory requirements for food-contact and biomedical uses, and the need for comprehensive life cycle assessments.
- Evident from the text: as a narrative review, it does not report a systematic search protocol, inclusion criteria, meta-analysis, or primary data; comparisons rely on heterogeneous studies with varying materials, loadings, processing methods, and testing conditions.
Model-written summary. Check it against the paper before relying on it.
Integrity signals
Registry
Cites
Statistics
Figures
![Figure 1 Various synthetic routes for the production of PCL (Adapted from [45], Open Access).](https://figures.cochat.ai/paper-figures/929959cd882c430c8a4ef9bea9d8de14/nanocellulose-reinforced-poly-lactic-acid-and-poly-caprolactone-bio-figure-1.jpg)
![Figure 2 Different synthetic methods for the production of PLA (Adapted from [54], Open Access).](https://figures.cochat.ai/paper-figures/f094a8cf5d9747498530d3ecda960ab0/nanocellulose-reinforced-poly-lactic-acid-and-poly-caprolactone-bio-figure-2.jpg)
![Figure 3 Schematic of the extraction of (a) CNCs and (b) CNFs from cellulose fibers via acid hydrolysis and mechanical process, respectively. The right-hand side represents a magnified view of the boxed region on the left to show cellulose at nanoscale (Adapted from [64], Open Access).](https://figures.cochat.ai/paper-figures/d93fbcb13b074286a3a7b7f0daab5573/nanocellulose-reinforced-poly-lactic-acid-and-poly-caprolactone-bio-figure-3.jpg)
![Figure 4 SEM micrographs of PLA/PCL blends at 95/5, 70/30, 60/40, and 30/70 w/w blend ratios at low (20 µm) and high (5 µm) magnifications. Arrows guide the reader to the PLA and the PCL phases. (Reproduced from [93], Open Access).](https://figures.cochat.ai/paper-figures/83d1fdf6b158487a9569bf5c4c72de88/nanocellulose-reinforced-poly-lactic-acid-and-poly-caprolactone-bio-figure-4.jpg)
Verification
Claims the paper makes
28 Valid · 5 Not valid · 66 Not checked · 50 Own results and interpretations
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“CNCs extracted via acid hydrolysis typically exhibit higher crystallinity indices (ca. 60–90%) due to removal of amorphous regions [62,63]”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 4. Nanocellulose: Extraction Methods and Characterization Techniques
What the sources say
- Partly supportedcites [62] Kusmono, 2020, Preparation and characterization of cellulose nanocrystal extracted from ramie fibers by sulfuric acid hydrolysis, Heliyon sourceExperimental — accuracy not yet measured
The X-ray diffraction section (page not provided) reports crystallinity indices of 80.32–90.77% for sulfuric-acid-hydrolyzed ramie CNCs and says removal of amorphous components might explain the increase. It does not establish that approximately 60–90% is a typical range for acid-hydrolyzed CNCs generally. (LLM, conf=0.84)
- Supportedcites [63] Mohomane, 2022, Effects of acid hydrolysis on the extraction of cellulose nanocrystals (CNCs): A review, Cellul. Chem. Technol. source
The Crystallinity Analysis section says acid hydrolysis generally increases crystallinity by removing amorphous regions and gives examples rising from 40% to 70% and from 60.4% to 90.4%. The CNCs Dimensions section describes CNC crystallinity as about 65%–95%, broadly consistent with the claim’s approximate 60%–90% range. (LLM, conf=0.88)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“High crystallinity and hydrophobicity of PCL also slow the degradation rate [6,49]”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 2. Synthesis and Properties of Poly(ε-caprolactone)
What the sources say
- Partly supportedcites [6] Ghanem, 2024, Polycaprolactone composite films infused with hyperbranched polyester/reduced graphene oxide: Influence on biodegradability, gas/water transport and antimicrobial properties for sustainable packaging, RSC Adv. sourceExperimental — accuracy not yet measured
The Introduction describes PCL as semi-crystalline and refers to its low degradation rate. The Thermal properties section reports about 71% crystallinity for neat PCL, and Surface wettability describes its surface as less hydrophilic. Neither section, nor the Ability for biodegradation section, says that crystallinity or hydrophobicity causes the slow degradation. (LLM, conf=0.82)
- Supportedcites [49] Limsukon, 2025, Impact of hydrolysis pretreatment on the compostability of biodegradable poly (caprolactone) and poly (lactic acid) films, RSC Appl. Polym. source
Section 3.4 states that PCL starts with high crystallinity and that crystalline regions resist water penetration, slowing degradation. Section 3.1 identifies PCL’s high hydrophobicity, alongside crystallinity, as a crucial factor in its slow molecular-weight decrease during hydrolysis. (LLM, conf=0.91)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
Every source the paper cites for this claim was checked and supports it.
In the paper
“but incorporating CNCs with micro-fibrillated cellulose into PLA increased the biodegradation of the composite by 60% under composting conditions.”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 6. Poly(Lactic Acid)/nanocellulose Bio-Nanocomposites: Preparation and Property Enhancements
What the sources say
- Supportedcites [85] Galera Manzano, L.M., Ruz Cruz, M.A., Moo Tun, N.M., Valadez González, A., and Mina Hernandez, J.H. (2021). Effect of cellulose and cellulose nanocrystal contents on the biodegradation, under composting conditions, of hierarchical PLA biocomposites. Polymers, 13. source
The Results (section 4.2, Weight Loss) report that after 180 days of composting, the simultaneous presence of MFC and CNC increased biodegradation by 60% for one composite formulation. Another formulation showed a 21% increase, so the 60% figure applies to a specific formulation rather than all MFC–CNC composites. (LLM, conf=0.92)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Supported
The cited sources that could be checked couldn’t confirm or dispute this claim.
In the paper
“Biodegradation is slowed by poor dispersion of CNCs on the PLA matrix or strong CNCs–PLA interfacial adhesion, which lowers water penetration and polymer chain mobility [84].”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 6. Poly(Lactic Acid)/nanocellulose Bio-Nanocomposites: Preparation and Property Enhancements
What the sources say
- Could not verifycites [84] Kelnar, I., Kaprálková, L., Krejčíková, S., Dybal, J., Vyroubalová, M., and Abdel-Mohsen, A. (2023). Effect of Polydopamine Coating of Cellulose Nanocrystals on Performance of PCL/PLA Bio-Nanocomposites. Materials, 16. sourceExperimental — accuracy not yet measured
Section 3.1 discusses CNC dispersion and affinity, and Section 3.4 reports hindered chain mobility during cooling. Neither connects those properties to slower biodegradation or reduced water penetration. Searches for biodegradation, water penetration, and degradation found no passage addressing that proposed mechanism; page numbers were not available in our copy. (LLM, conf=0.74)
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: unclear — It is unclear whether the paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Could not verify
The cited sources support only part of this claim — read each source’s verdict below.
In the paper
“Performance-wise, studies summarized in Table 5 report that composites of PLA/PCL exhibit improved tensile strength, modulus, and toughness compared to neat PLA/PCL blends [24,25,31,32].”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 8. Poly(Lactic Acid)/poly(ε-caprolactone)-Based Composites Hybrid Reinforcements: Processing and Performance
What the sources say
- Partly supportedcites [24] Rytlewski, 2022, Electron-induced structural changes in flax fiber reinforced PLA/PCL composites, analyzed using the rule of mixtures, Ind. Crops Prod. sourceExperimental — accuracy not yet measured
The Conclusions report that electron irradiation increased tensile strength and modulus in flax-fiber-reinforced PLA/PCL composites, but did not improve impact toughness. The Results and discussion report a toughness increase when the PCL content of the blend reached 30 wt%. Neither passage establishes that the fiber-reinforced composites improved all three properties compared with neat PLA/PCL blends. (LLM, conf=0.84)
- Not checked — no full text of the sourcecites [25] Rao, 2019, Enhancement of mechanical properties of PLA/PCL (80/20) blend by reinforcing with MMT nanoclay, Mater. Today Proc. source
- Not checked — no full text of the sourcecites [31] Malinowski, 2016, Mechanical properties of PLA/PCL blends crosslinked by electron beam and TAIC additive, Chem. Phys. Lett. source
- Not checked — no full text of the sourcecites [32] Chen, 2023, Fully biodegradable PLA composite with improved mechanical properties via 3D printing, Mater. Lett. source
plainstates a cause- Asserted: passes — The authors put it forward as true.
- Checkable: passes — It can be checked against evidence.
- Load-bearing: passes — The paper’s conclusions depend on it.
- Based: passes — The paper gives a reason why it holds.
- Partly supported
61 more claims · 9 with their cited sources checked
Create a free account to see all 149 claims and to verify the 1 reference still open.
- It may state two separate claims as one. 74
- Probably not a substantial claim. 20
- The quote only partly states this claim. 1
Self-check
Percentages, sums and reported differences re-computed from the paper’s own numbers.
Each contradiction between two passages listed here was confirmed by an independent check.
Rated major: it would touch a result — a value a result rests on, reported and recomputed p-values on opposite sides of the significance level, two passages that conflict with no sign which is right, or a cited work retracted before this paper was published.
In the paper
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 8. Poly(Lactic Acid)/poly(ε-caprolactone)-Based Composites Hybrid Reinforcements: Processing and Performance
“The O.MMT variant notably doubles the indentation modulus compared to neat PCL”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 8. Poly(Lactic Acid)/poly(ε-caprolactone)-Based Composites Hybrid Reinforcements: Processing and Performance
“Improved indentation modulus by 50% compared to that of PCL.”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 5. Poly(ε-caprolactone)/nanocellulose Bio-Nanocomposites: Preparation and Property Enhancements
“| PCL/CNCs | Starch | 1.0, 3.0, and 5.0 | Solution casting |”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > References
“The starch nanocrystal filled biodegradable poly (ε-caprolactone) composite membrane with highly improved properties”
Rated minor: it would not touch a result — a value no result rests on, a p-value that stays on the same side of the significance level, or a conflict that is clerical, resolved elsewhere in the paper, or outside its own findings.
In the paper
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 7. Poly(Lactic Acid)/poly(ε-caprolactone) Biopolymer Blends: Morphology, Compatibility and Properties
“in the 30PLA/70PCL blend (Figure 4). In other studies, this PLA/PCL blend ratio (i.e., 80/20) was also used”
§ Nanocellulose-Reinforced Poly(Lactic Acid) and Poly(ε-caprolactone) Bio-Nanocomposites: A Review and Future Outlook for Poly(Lactic Acid)/Poly(ε-caprolactone) Blend Systems > 7. Poly(Lactic Acid)/poly(ε-caprolactone) Biopolymer Blends: Morphology, Compatibility and Properties
“this PLA/PCL blend ratio (i.e., 80/20)”
Citations
Cites
The return of a forgotten polymer—Polycaprolactone in the 21st century
Woodruff, M. A., & Hutmacher, D. W. (2010) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2010.04.002 · Cited by 4,033 · cited 2×
“40%, a melting temperature in the range of 58–64 ◦ C, and a glass transition temperature in the range of − 65 to − 60 ◦ C (see Table 1) [35,46,47].”
Farah, S., Anderson, D. G., & Langer, R. (2016) · Advanced Drug Delivery Reviews · doi:10.1016/j.addr.2016.06.012 · Cited by 3,443 · cited 1×
“According to Farah et al. [50] and Luyt et al. [51], PLA is primarily synthesized via (i) direct polycondensation of lactic acid, (ii) azeotropic dehydrative condensation, and (iii) ROP of lactide, as illustrated in Figure 2.”
Poly(lactic acid) crystallization
Saeidlou, S., Huneault, M. A., Li, H., & Park, C. B. (2012) · Progress in Polymer Science · doi:10.1016/j.progpolymsci.2012.07.005 · Cited by 1,606 · cited 1×
“In general, PLA consists of crystalline domains formed by thin plate-like stacks of folded polymer chains, connected to amorphous zones by chain folds and tie molecules [55].”
Nanocellulose: Extraction and application
Phanthong, P., Reubroycharoen, P., Hao, X., Xu, G., Abudula, A., & Guan, G. (2018) · Carbon Resources Conversion · doi:10.1016/j.crcon.2018.05.004 · Cited by 1,028
Electrospun Polycaprolactone (PCL) Degradation: An In Vitro and In Vivo Study
Dias, J. R., Sousa, A., Augusto, A., Bártolo, P. J., & Granja, P. L. (2022) · Polymers · doi:10.3390/polym14163397 · Cited by 293 · cited 1×
“The recent literature has increasingly focused on alternative synthesis routes, including enzyme-catalyzed and organo-catalytic polymerization, to address concerns about the residual toxicity of tin-based catalysts such as stannous octoate in biomedical applications [42–44].”
Effect of the addition of poly (D-lactic acid) on the thermal property of poly (L-lactic acid)
Yamane, H., & Sasai, K. (2003) · Polymer · doi:10.1016/s0032-3861(03)00092-2 · Cited by 266 · cited 3×
“Research highlights that poly(L-lactic acid) is semi-crystalline with the degree of crystallinity of ca. 20–40% and exhibits a higher melting point (~170–180 ◦ C), while poly(D,L-lactic acid) is mostly amorphous with the degree of crystallinity of ca. 0 –10% and is more ductile [53].”
Khoshkava, V., & Kamal, M. R. (2013) · Biomacromolecules · doi:10.1021/bm400784j · Cited by 235 · cited 1×
“Surface modification of NC has been shown to lower its surface energy, improving the polymer-filler interaction and thus achieving uniform dispersion [79].”
Kusmono, Listyanda, R. F., Wildan, M. W., & Ilman, M. N. (2020) · Heliyon · doi:10.1016/j.heliyon.2020.e05486 · Cited by 231 · cited 1×
“%) due to removal of amorphous regions [62,63].”
Effect of Molecular Weight on the Crystallization and Melt Memory of Poly(ε-caprolactone) (PCL)
Fernández-Tena, A., Pérez-Camargo, R. A., Coulembier, O., Sangroniz, L., Aranburu, N., Guerrica-Echevarria, G., Liu, G., Wang, D., Cavallo, D., & Müller, A. J. (2023) · Macromolecules · doi:10.1021/acs.macromol.3c00234 · Cited by 200
Pracella, M., Haque, M. M.-U., & Puglia, D. (2014) · Polymer · doi:10.1016/j.polymer.2014.06.071 · Cited by 193 · cited 2×
“To address this, researchers have investigated surface modification techniques, such as grafting with glycidyl methacrylate, to enhance interfacial adhesion and dispersion of NC in PLA [18].”
Ntrivala, M. A., Pitsavas, A. C., Lazaridou, K., Baziakou, Z., Karavasili, D., Papadimitriou, M., Ntagkopoulou, C., Balla, E., & Bikiaris, D. N. (2025) · European Polymer Journal · doi:10.1016/j.eurpolymj.2025.114033 · Cited by 178
Polycaprolactone: Synthesis, Properties, and Applications
Guarino, V., Gentile, G., Sorrentino, L., & Ambrosio, L. (2017) · Encyclopedia of Polymer Science and Technology · doi:10.1002/0471440264.pst658 · Cited by 163 · cited 1×
“…via (i) ring-opening polymerization (ROP) (ionic-or metal-catalyzed, and coordination insertion method) of the cyclic monomer ε -caprolactone, (ii) cyclic ketene acetals using radical ring-opening polymerization (rROP), and (iii) 6-hydroxycaproic acid polycondensation, as shown in Figure 1 [39].”
Thermal and mechanical properties of PLA-based multiscale cellulosic biocomposites
Ruz-Cruz, M. A., Herrera-Franco, P. J., Flores‐Johnson, E. A., Moreno‐Chulim, M. V., Galera-Manzano, L. M., & Valadez-González, A. (2022) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2022.02.072 · Cited by 145
Luzi, F., Fortunati, E., Puglia, D., Petrucci, R., Kenny, J. M., & Torre, L. (2015) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2015.08.016 · Cited by 128 · cited 1×
“Solvent casting, often used in early-stage studies, enables good initial dispersion of NC in PLA due to solvent-assisted mixing [15,17,37,65,77].”
Can Biodegradable Plastics Solve Plastic Solid Waste Accumulation?
Luyt, A. S., & Malik, S. S. (2019) · Plastics to Energy · doi:10.1016/b978-0-12-813140-4.00016-9 · Cited by 114 · cited 2×
“According to Farah et al. [50] and Luyt et al. [51], PLA is primarily synthesized via (i) direct polycondensation of lactic acid, (ii) azeotropic dehydrative condensation, and (iii) ROP of lactide, as illustrated in Figure 2.”
Miao, C., & Hamad, W. Y. (2016) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2016.08.012 · Cited by 112 · cited 1×
“Solvent casting, often used in early-stage studies, enables good initial dispersion of NC in PLA due to solvent-assisted mixing [15,17,37,65,77].”
Rashtchian, M., Hivechi, A., Bahrami, S. H., Milan, P. B., & Simorgh, S. (2020) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2020.115873 · Cited by 112 · cited 1×
“On the other hand, solution/solvent casting, often using chloroform or dichloromethane as solvents, facilitates better initial dispersion but is limited by environmental and processing drawbacks [20,22,23,36,67,68].”
Sessini, V., Navarro-Baena, I., Arrieta, M. P., Dominici, F., López, D., Torre, L., Kenny, J. M., Dubois, P., Raquez, J.-M., & Peponi, L. (2018) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2018.04.012 · Cited by 111
Ahmad, N. D., Kusmono, Wildan, M. W., & Herianto (2023) · Results in Engineering · doi:10.1016/j.rineng.2022.100842 · Cited by 103 · cited 3×
“As highlighted in the literature [14–19], tensile strength and Young’s modulus of PLA composites increased notably with the incorporation of well-dispersed CNCs or CNFs, even at low filler contents ( 5 wt.%).”
Kalita, N. K., Bhasney, S. M., Mudenur, C., Kalamdhad, A., & Katiyar, V. (2020) · Chemosphere · doi:10.1016/j.chemosphere.2020.125875 · Cited by 101
Zhu, B., Wang, Y., Liu, H., Ying, J., Liu, C., & Shen, C. (2020) · Composites Science and Technology · doi:10.1016/j.compscitech.2020.108048 · Cited by 94 · cited 3×
“PLA, characterized by high stiffness and brittleness, and PCL, known for its flexibility and toughness, are inherently immiscible due to differences in polarity and crystallinity, which results in phase-separated morphologies [26,27,88,89].”
Cellulose Nanocrystals (CNCs) and Cellulose Nanofibers (CNFs) as Adsorbents of Heavy Metal Ions
Kurniawan, T. W., Sulistyarti, H., Rumhayati, B., & Sabarudin, A. (2023) · Journal of Chemistry · doi:10.1155/2023/5037027 · Cited by 89 · cited 1×
“The characterization of NC has been reported in the literature, with various studies highlighting how morphological, structural, and thermal properties influence their performance in polymer nanocomposites [58,59,61].”
Polylactic acid (PLA)-based multifunctional and biodegradable nanocomposites and their applications
Islam, M. S., Elahee, G. M. F., Fang, Y., Yu, X. (., Advincula, R. C., & Cao, C. (. (2025) · Composites Part B Engineering · doi:10.1016/j.compositesb.2025.112842 · Cited by 86 · cited 1×
“Beyond mechanical improvements, thermal stability and crystallization behavior of PLA are positively influenced by NC [82].”
Botlhoko, O. J., Ramontja, J., & Ray, S. S. (2018) · Polymer Degradation and Stability · doi:10.1016/j.polymdegradstab.2018.05.025 · Cited by 81
Dadras Chomachayi, M., Jalali-arani, A., Beltrán, F. R., de la Orden, M. U., & Martínez Urreaga, J. (2020) · Journal of Polymers and the Environment · doi:10.1007/s10924-020-01684-0 · Cited by 76 · cited 5×
“Melt blending these SFNPs at 1.0 wt.% offers benefits suitable for food packaging, where thermal resistance and safety are priorities [27].”
InfluentialWang, W., Niu, B., Liu, R., Chen, H., Fang, X., Wu, W., Wang, G., Gao, H., & Mu, H. (2023) · Food Chemistry · doi:10.1016/j.foodchem.2023.136905 · Cited by 68
Trivedi, A. K., & Gupta, M. K. (2024) · Scientific Reports · doi:10.1038/s41598-024-71619-5 · Cited by 49 · cited 1×
“From the biodegradation point, well-dispersed hydrophilic CNCs on the PLA matrix improve water uptake and increase the accessibility of ester bonds to microbes and hy-Materials drolysis, which speeds up the degradation rate [83].”
Enhancement of mechanical properties of PLA/PCL (80/20) blend by reinforcing with MMT nanoclay
Umamaheswara Rao, R., Venkatanarayana, B., & Suman, K. N. S. (2019) · Materials Today Proceedings · doi:10.1016/j.matpr.2019.06.280 · Cited by 45 · cited 1×
“Surface functionalization of MMT nanoclay promotes better polymer compatibility and increases tensile strength, essential for applications like printing plates [25].”
Preparation and research of PCL/cellulose composites: Cellulose derived from agricultural wastes
Chen, J., Huang, Y., Deng, L., Jiang, H., Yang, Z., Yang, R., & Wu, D. (2023) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2023.123785 · Cited by 45 · cited 2×
“For instance, CNCs have been shown to enhance the crystallinity of PCL [21,22,68,69].”
Hassan, M. L., Bras, J., Hassan, E. A., Fadel, S. M., & Dufresne, A. (2012) · Journal of Applied Polymer Science · doi:10.1002/app.36373 · Cited by 43 · cited 3×
“[21–23, 36, 67].”
Xu, C., Chen, C., & Wu, D. (2018) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2017.11.001 · Cited by 43 · cited 3×
“[21–23, 36, 67].”
Gan, I., & Chow, W. S. (2019) · Journal of Thermoplastic Composite Materials · doi:10.1177/0892705718772866 · Cited by 43 · cited 3×
“Thermogravimetric analysis (TGA) has been used to evaluate thermal stability, showing that CNCs produced via sulfuric acid hydrolysis degrade at lower temperatures (~180–250 ◦ C) due to the presence of sulfate ester groups [65].”
Hong, J. K., Cooke, S. L., Whittington, A. R., & Roman, M. (2021) · Frontiers in Bioengineering and Biotechnology · doi:10.3389/fbioe.2021.605924 · Cited by 39
Effects of acid hydrolysis on the extraction of cellulose nanocrystals (CNCs): A review
Department of Chemistry, U. O. Z., MOHOMANE, S. M., MOTLOUNG, S. V., Department of Chemical and Physical Sciences, P. B. X., KOAO, L. F., Department of Physics, U. O. T. F. S. (. C., MOTAUNG, T. E., & Department of Chemistry, S. M. H. S. U. (2022) · Cellulose Chemistry and Technology · doi:10.35812/cellulosechemtechnol.2022.56.61 · Cited by 39 · cited 1×
“%) due to removal of amorphous regions [62,63].”
Hivechi, A., Bahrami, S. H., Siegel, R. A., Siehr, A., Sahoo, A., Milan, P. B., Joghataei, M. T., Amoupour, M., & Simorgh, S. (2021) · Materials Science and Engineering C · doi:10.1016/j.msec.2020.111855 · Cited by 38
Galera Manzano, L. M., Ruz Cruz, M. Á., Moo Tun, N. M., Valadez González, A., & Mina Hernandez, J. H. (2021) · Polymers · doi:10.3390/polym13111855 · Cited by 36 · cited 1×
“On the other hand, the inclusion of micro-fibrillated cellulose improved water uptake [85].”
Li, J., & Wu, D. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.02.123 · Cited by 36 · cited 2×
“For instance, CNCs have been shown to enhance the crystallinity of PCL [21,22,68,69].”
Mechanical properties of PLA/PCL blends crosslinked by electron beam and TAIC additive
Malinowski, R. (2016) · Chemical Physics Letters · doi:10.1016/j.cplett.2016.09.022 · Cited by 34 · cited 2×
“…(TAIC) serve as compatibilizers that enhance mechanical properties by improving the miscibility of PLA and PCL. TAIC, added via melt blending, not only increases strength and modulus but also reduces phase separation in PLA/PCL blends, expanding its use in both packaging and biomedical fields [31].”
Liu, Z.-H., Li, Y., Zhang, C.-J., Zhang, Y.-Y., Cao, X.-H., & Zhang, X.-H. (2020) · Giant · doi:10.1016/j.giant.2020.100030 · Cited by 34 · cited 1×
“For example, the zinc–cobalt double-metal cyanide complex [Zn-Co(III) DMCC] produced higher molecular weight PCL, which exhibits better tensile strength and elongation at break, but may compromise processability due to its increased viscosity [41].”
Fabrication and characterization of polycaprolactone-based green materials for drug delivery
Kurakula, M., Rao, G. S. N. K., & Yadav, K. S. (2021) · Applications of Advanced Green Materials · doi:10.1016/b978-0-12-820484-9.00016-7 · Cited by 34
Fernández‐Tena, A., Otaegi, I., Irusta, L., Sebastián, V., Guerrica‐Echevarria, G., Müller, A. J., & Aranburu, N. (2023) · Macromolecular Materials and Engineering · doi:10.1002/mame.202300213 · Cited by 34
Widjaja, T., Hendrianie, N., Nurkhamidah, S., Altway, A., Yusuf, B., Fakhrizal, F., Rohma, A. A. Z., & Pahlevi, A. (2023) · Heliyon · doi:10.1016/j.heliyon.2023.e17985 · Cited by 32 · cited 1×
“The synthesis process is typically catalyzed by tin(II) octoate, which allows for tuning of the molecular architecture of the polymer [52,53].”
Esterified cellulose nanofibres from saw dust using vegetable oil
Mokhena, T. C., & John, M. J. (2020) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2020.01.278 · Cited by 31 · cited 1×
“The characterization of NC has been reported in the literature, with various studies highlighting how morphological, structural, and thermal properties influence their performance in polymer nanocomposites [58,59,61].”
Development and characterisation of sugarcane bagasse nanocellulose/PLA composites
Gond, R. K., Naik, T. P., Gupta, M. K., & Singh, I. (2022) · Materials Technology · doi:10.1080/10667857.2022.2088616 · Cited by 30 · cited 1×
“Studies using DSC and TGA show that NC can act as a nucleating agent, accelerating PLA crystallization and enhancing its thermal resistance [14,16,17,65].”
Motloung, M. P., Ojijo, V. O., Bandyopadhyay, J., & Ray, S. S. (2019) · Journal of Applied Polymer Science · doi:10.1002/app.48665 · Cited by 29
Mondal, K., Bhagabati, P., Goud, V. V., Sakurai, S., & Katiyar, V. (2021) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2021.09.114 · Cited by 29
Fully biodegradable PLA composite with improved mechanical properties via 3D printing
Chen, Y., Lu, T., Li, L., Zhang, H., Wang, H., & Ke, F. (2023) · Materials Letters · doi:10.1016/j.matlet.2022.133543 · Cited by 28 · cited 2×
“In contrast, BNC is biosynthesized by microbial fermentation and is valued for its ultrafine network structure, high purity, and superior water-holding capacity, which make it especially suitable for biomedical applications [32].”
Rytlewski, P., Gohs, U., Stepczyńska, M., Malinowski, R., Karasiewicz, T., & Moraczewski, K. (2022) · Industrial Crops and Products · doi:10.1016/j.indcrop.2022.115587 · Cited by 27 · cited 3×
“Meanwhile, higher loading of natural fibers, such as flax fiber, at 20 wt.%, significantly enhances mechanical properties through extrusion and injection molding, demonstrating their potential for robust packaging materials [24].”
InfluentialJeon, H., Kim, M.-S., Park, S. B., Kim, S., Lee, M., Park, S.-A., Hwang, S. Y., Koo, J. M., Oh, D. X., & Park, J. (2023) · Cellulose · doi:10.1007/s10570-023-05615-9 · Cited by 27
Soriano-Cuadrado, B., Fontecha-Cámara, M. A., Mañas-Villar, M., et al. (2024) · Polymers · doi:10.3390/polym16172462 · Cited by 27
Development and characterization of PLA/PCL blend filaments and 3D printed scaffolds
Eryildiz, M., Karakus, A., & Altan Eksi, M. (2025) · Journal of Materials Engineering and Performance · doi:10.1007/s11665-024-10247-6 · Cited by 27 · cited 1×
“In other studies, this PLA/PCL blend ratio (i.e., 80/20) was also used to fabricate the blends and it was found that both the mechanical and thermal properties of the resulting 3D printed scaffolds were significantly improved [94,95].”
Ghanem, A. F., Yassin, M. A., Cosquer, R., Gouanvé, F., Espuche, E., & Abdel Rehim, M. H. (2024) · RSC Advances · doi:10.1039/d3ra08948g · Cited by 26
Eryildiz, M., Karakus, A., Demirci, M., Altintas Kadirhan, O., & Eksi Altan, M. (2025) · Polymers for Advanced Technologies · doi:10.1002/pat.70133 · Cited by 25 · cited 1×
“This was attributed to the disruption of the PLA crystal structure by excess PCL, which hinders the effective chain arrangement [92].”
Viscoelastic properties of PLA/PCL blends compatibilized with different methods
Shin, B. Y., & Han, D. H. (2017) · Korea-Australia Rheology Journal · doi:10.1007/s13367-017-0029-8 · Cited by 23 · cited 4×
“PLA, characterized by high stiffness and brittleness, and PCL, known for its flexibility and toughness, are inherently immiscible due to differences in polarity and crystallinity, which results in phase-separated morphologies [26,27,88,89].”
InfluentialVidakis, N., Petousis, M., Michailidis, N., David, C., Mountakis, N., Papadakis, V., Sfakiotakis, E., Sagris, D., & Argyros, A. (2024) · Cellulose · doi:10.1007/s10570-024-05851-7 · Cited by 23 · cited 1×
“For example, in one study, 3 wt.% NC was found to be optimal for dispersion and overall properties in PLA [98]; however, another study reported an optimal NC content of 4 wt.% in PCL [5].”
Chitbanyong, K., Pisutpiched, S., Khantayanuwong, S., Theeragool, G., & Puangsin, B. (2020) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2020.09.124 · Cited by 22 · cited 2×
“The characterization of NC has been reported in the literature, with various studies highlighting how morphological, structural, and thermal properties influence their performance in polymer nanocomposites [58,59,61].”
Wu, J.-J., Gao, N., Jiang, L., Zhong, G.-J., Deng, C., & Gao, X. (2022) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2022.03.172 · Cited by 22 · cited 3×
“As highlighted in the literature [14–19], tensile strength and Young’s modulus of PLA composites increased notably with the incorporation of well-dispersed CNCs or CNFs, even at low filler contents ( 5 wt.%).”
D'Amario, J., Limsukon, W., Bher, A., & Auras, R. (2025) · RSC Applied Polymers · doi:10.1039/d5lp00041f · Cited by 22
Kiani, P., Sedighi, M., Kasaeian-Naeini, M., & Jabbari, A. H. (2025) · Journal of Materials Research and Technology · doi:10.1016/j.jmrt.2025.04.082 · Cited by 21 · cited 1×
“In other studies, this PLA/PCL blend ratio (i.e., 80/20) was also used to fabricate the blends and it was found that both the mechanical and thermal properties of the resulting 3D printed scaffolds were significantly improved [94,95].”
Şen, İ., & Sever, K. (2025) · Polymer Bulletin · doi:10.1007/s00289-025-05698-3 · Cited by 20
Fabrication of Polymer/Graphene Biocomposites for Tissue Engineering
Meneses, J., van de Kemp, T., Costa‐Almeida, R., Pereira, R. F., Magalhães, F. D., Castilho, M. D., & Pinto, A. M. (2022) · Polymers · doi:10.3390/polym14051038 · Cited by 19
Wongthanaroj, D., Jessmore, L. A., Lin, Y., Bergholz, T. M., Stark, N. M., Sabo, R. C., & Matuana, L. M. (2022) · Applied Food Research · doi:10.1016/j.afres.2022.100222 · Cited by 19 · cited 1×
“However, industrial relevance has driven growing interest in melt processing techniques, which are environmentally favorable and scalable [14,18,19,78].”
Ma, R., Zhang, Q., Wang, S., Li, B., Ma, L., Zhang, L., Yu, J., Fan, Y., & Wang, Z. (2024) · Industrial Crops and Products · doi:10.1016/j.indcrop.2024.118134 · Cited by 19 · cited 2×
“Melting temperatures of the composites also increased, which improved the thermal processability of PCL [71].”
Motloung, B., Pfukwa, R., & Klumperman, B. (2024) · Macromolecular Materials and Engineering · doi:10.1002/mame.202300457 · Cited by 19 · cited 2×
“…are extracted through mechanical fibrillation methods including high-pressure homogenization and grinding, often aided by chemical or enzymatic pre-treatments such as 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)-mediated oxidation to enhance fibrillation efficiency and reduce energy demand [58–60].”
Self-citationHou, Y., Wang, W., & Bártolo, P. (2024) · Bio-Design and Manufacturing · doi:10.1007/s42242-024-00280-8 · Cited by 19
Biocompatible composites based on alginate, polycaprolactone, and nanocellulose - A review
Ikhtiarini, N., Kamil, M. Z., Bukit, B. F., Juliadmi, D., Prasetiyo, K. W., Fransiska, D., Sedayu, B. B., Subiyanto, B., Sulastiningsih, I. M., Rochima, E., et al. (2025) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2025.143423 · Cited by 18
Wang, Z. P., Ruan, W., Rong, M. Z., & Zhang, M. Q. (2023) · Journal of Material Science and Technology · doi:10.1016/j.jmst.2023.07.017 · Cited by 17
Khoo, R. Z., Chow, W. S., & Ismail, H. (2023) · Journal of Thermoplastic Composite Materials · doi:10.1177/08927057221098972 · Cited by 15 · cited 2×
“Studies using DSC and TGA show that NC can act as a nucleating agent, accelerating PLA crystallization and enhancing its thermal resistance [14,16,17,65].”
Avella, A., Idström, A., Mincheva, R., Nakayama, K., Evenäs, L., Raquez, J.-M., & Lo Re, G. (2022) · Composites Part A Applied Science and Manufacturing · doi:10.1016/j.compositesa.2022.107166 · Cited by 15 · cited 2×
“For example, Avella et al. [66] demonstrated that treated CNCs improved interfacial adhesion and dispersion within PCL, resulting in enhanced mechanical performance compared to unmodified fillers.”
Nourany, M., Makaremy, A., Bazrpash, S., & Hosseini, S. (2025) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2025.140149 · Cited by 15
Ivanov, E., Kotsilkova, R., Georgiev, V., Batakliev, T., & Angelov, V. (2025) · Journal of Manufacturing and Materials Processing · doi:10.3390/jmmp9020035 · Cited by 15 · cited 2×
“In contrast, Ivanov et al. [93] reported that an increase in PLA crystallinity was not observed until the PCL content in the blends reached ca. 40 wt.%.”
Renewable rice straw cellulose nanofibril reinforced poly (ε-caprolactone) composite films
Qiao, X., Wang, Z., & Sun, K. (2022) · Materials Chemistry and Physics · doi:10.1016/j.matchemphys.2022.126879 · Cited by 13
Sikhosana, S. T., Gumede, T. P., Malebo, N. J., Ogundeji, A. O., & Motloung, B. (2023) · Polymer Engineering & Science · doi:10.1002/pen.26293 · Cited by 13 · cited 1×
“For example, in one study, 3 wt.% NC was found to be optimal for dispersion and overall properties in PLA [98]; however, another study reported an optimal NC content of 4 wt.% in PCL [5].”
Self-citationSalmani, M. R., Shirazi, F., Goodarzi, K., Noormohammadi, F., & Nourany, M. (2024) · Journal of Polymers and the Environment · doi:10.1007/s10924-024-03392-5 · Cited by 13
Kumalo, F. I., Malimabe, M. A., Mosoabisane, M. F. T., & Gumede, T. P. (2025) · doi:10.20944/preprints202502.1813.v1 · Cited by 13
Self-citationKumalo, F. I., Malimabe, M. A., Mosoabisane, M. F. T., & Gumede, T. P. (2025) · Polymers · doi:10.3390/polym17070971 · Cited by 13
Self-citationN’Gatta, K. M., Assanvo, E. F., El Hayek, J., Masquelez, N., Kamgang Syapnjeu, P., Deabate, S., Bonniol, V., Soussan, L., Zamora-Ledezma, C., Elango, J., et al. (2025) · ACS Applied Materials & Interfaces · doi:10.1021/acsami.5c06504 · Cited by 12
Gong, W., Li, M., Sun, J., Zhang, F., Tian, T., Yin, Y., & Wang, C. (2025) · Composites Communications · doi:10.1016/j.coco.2025.102501 · Cited by 11 · cited 1×
“Properties such as thermal stability, hydrophilicity, and enzymatic degradation rate were also enhanced by CNCs-g -PEG incorporation [81].”
Slouf, M., Ujcic, A., Nevoralova, M., Vackova, T., Fambri, L., & Kelnar, I. (2020) · Frontiers in Materials · doi:10.3389/fmats.2020.00188 · Cited by 10 · cited 2×
“The literature shows that reinforcement strategies improve interfacial adhesion, dispersion, and composite functionality [24,27,31–34 , 89].”
Catalytic regulation of oligomers in polycaprolactone
Gong, C., Li, J., Yi, C., & Qu, S. (2021) · Molecular Catalysis · doi:10.1016/j.mcat.2021.111594 · Cited by 10
Ye, G., Yong, Q., Hu, L., Rosqvist, E., Peltonen, J., Hu, Y., Xu, W., & Xu, C. (2025) · International Journal of Biological Macromolecules · doi:10.1016/j.ijbiomac.2025.141371 · Cited by 9 · cited 1×
“Grafting of PLA chains onto NC surfaces results in more homogeneous composites and superior mechanical behavior [80].”
Haghgoo, G., Dadashi, P., & Babaei, A. (2025) · Polymers for Advanced Technologies · doi:10.1002/pat.70113 · Cited by 9
Wu, C., Wu, B., Abdalkarim, S. Y. H., Wang, M., Zou, Z., Jin, M., & Yu, H.-Y. (2025) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2025.123926 · Cited by 9 · cited 1×
“Similarly, it has been reported to accelerate the crystallization kinetics of PLA, thereby increasing its overall crystallinity [19,86,87].”
Treatment effects of 3D-printed PCL/Fe3O4@ ZIF-8 magnetic nanocomposite on infected bone defect
Xiao, Y., Ding, Y., Qiu, J., et al. (2024) · International Journal of Bioprinting · doi:10.36922/ijb.2271 · Cited by 8
Wahbi, M., Wen, Y., Kontopoulou, M., & De France, K. J. (2025) · Carbohydrate Polymers · doi:10.1016/j.carbpol.2025.124471 · Cited by 8 · cited 1×
“Similarly, it has been reported to accelerate the crystallization kinetics of PLA, thereby increasing its overall crystallinity [19,86,87].”
Kelnar, I., Kaprálková, L., Krejčíková, S., Dybal, J., Vyroubalová, M., & Abdel-Mohsen, A. M. (2023) · Materials · doi:10.3390/ma16031087 · Cited by 7 · cited 1×
“Biodegradation is slowed by poor dispersion of CNCs on the PLA matrix or strong CNCs–PLA interfacial adhesion, which lowers water penetration and polymer chain mobility [84].”
Rocha, J. M., Sousa, R. P. C. L., Sousa, D., Tohidi, S. D., Ribeiro, A., Fangueiro, R. M. E. S., & Ferreira, D. P. (2025) · Applied Sciences · doi:10.3390/app15052301 · Cited by 7
Chanthavong, V., Cabo, M., Prabhakar, M. N., Woo, L. D., & Song, J. (2025) · Polymer Engineering & Science · doi:10.1002/pen.27241 · Cited by 7
Batakliev, T., Georgiev, V., Ivanov, E., Angelov, V., & Kotsilkova, R. (2025) · Processes · doi:10.3390/pr13051328 · Cited by 6 · cited 1×
“However, in PLA/PCL blends, the deformation mechanism largely depends on interfacial adhesion, blend composition, and temperature [99].”
Widjaja, T., Rohmah, A. A. Z., Nurkhamidah, S., Ni'mah, H., Wardhono, E. Y., Saputra, B. Y. E., & Sari, C. Y. (2025) · Case Studies in Chemical and Environmental Engineering · doi:10.1016/j.cscee.2025.101186 · Cited by 5
Ilhan, R., Gumus, O. Y., & Lekesiz, H. (2026) · Polymer Composites · doi:10.1002/pc.70459 · Cited by 5
Gumede, T. P., Shingange, K., Mbule, P., & Motloung, B. (2022) · Polymers from Renewable Resources · doi:10.1177/20412479221109912 · Cited by 5 · cited 1×
“The degree of miscibility dictates the extent of molecular-level interactions between the polyesters, which in turn strongly influences the development of the blend morphology, and thus the mechanical properties and thermal behavior of the blends [90,91].”
Self-citationKarpova, S. G., Olkhov, A. A., Varyan, I. A., Khan, O. I., Botin, A. A., Naletova, A. V., Popov, A. A., & Iordanskii, A. L. (2024) · doi:10.20944/preprints202404.0063.v1 · Cited by 4
Ye, G., Yu, Y., Wu, C., Zhang, H., Zhao, Y., Bi, H., & Xu, C. (2025) · Industrial Crops and Products · doi:10.1016/j.indcrop.2025.121699 · Cited by 4 · cited 1×
“PCL-grafted CNCs, obtained via ring-opening polymerization of caprolactone monomer using the “grafting from” approach, have also been reported [70].”
Sikhosana, S. T., Gumede, T. P., Malebo, N. J., Ogundeji, A. O., & Motloung, B. (2023) · Polymers from Renewable Resources · doi:10.1177/20412479221146249 · Cited by 4 · cited 1×
“Nanocellulose (NC) is a renewable and biodegradable nanomaterial typically derived from lignocellulosic biomass [57].”
Self-citationKarpova, S. G., Olkhov, A. A., Varyan, I. A., Хан, О. И., Botin, A. A., Naletova, A. V., Popov, A. A., & Иорданский, А. Л. (2024) · Polymers · doi:10.3390/polym16101307 · Cited by 4
Vala, N. S., Bavaliya, K. J., Raj, M., & Raj, L. (2025) · Polymer-Plastics Technology and Materials · doi:10.1080/25740881.2025.2560913 · Cited by 4
Carotenuto, M. R., Cavallaro, G. P., Chinnici, I., Lazzara, G., & Milioto, S. (2025) · Journal of Thermal Analysis and Calorimetry · doi:10.1007/s10973-025-14178-9 · Cited by 2
Chaipakdee, N., Hemvichian, K., Lertsarawut, P., Rimdusit, S., & Tiptipakorn, S. (2025) · IOP Conference Series Materials Science and Engineering · doi:10.1088/1757-899x/1325/1/012003 · Cited by 1 · cited 1×
“The choice of a catalyst affects the molecular weight distribution of the resulting PCL, which in turn influences its mechanical and thermal properties [40].”
Selikane, D. G. A., Gumede, T. P., Shingange, K., Malevu, T. D., Ngwenya, M., & Kumalo, F. (2024) · Journal of Biomimetics, Biomaterials and Biomedical Engineering · doi:10.4028/p-pt5csd
Self-citationMiscibility effect of biodegradable aliphatic poly(butylene succinate)/aromatic polycarbonate blendsPreprint
Gumede, T. P., Shingange, K., Mbule, P. S., et al. (2021) · Research Square · doi:10.21203/rs.3.rs-818619/v1
Self-citation
Research works printed but not linked: 2
- Gond, 2020, Development of PLA Based Nanocellulose Film for Packaging Applications, J. Indian Chem. Soc., 97, 1621
- Refinetti, D., Sonzogni, A., Manenti, F., and Nascimento Lima, N.M. (2014). Modeling and simulation of poly (l-lactide) polymerization in batch reactor. Chemical Engineering Transactions, AIDIC.
Cited by
Li, E., Cui, C., Shangguan, W., Qu, Y., Wang, Z., Li, K., & Yin, J. (2026) · Chemical Engineering Journal · doi:10.1016/j.cej.2026.173664 · Cited by 4
He, Y., Dan, Y., Jiang, L., Huang, Y., Zhang, H., & Qi, Y. (2026) · Polymers · doi:10.3390/polym18020212 · Cited by 4
“This material exhibits excellent mechanical properties and degradation characteristics, and capable of biodegradation, has been widely applied in various fields in recent years to address the environmental issues associated with traditional plastics [4,5].”
Ngwenya, M., Gumede, T. P., & Motloung, B. (2026) · Polymers · doi:10.3390/polym18091132 · Cited by 1
“Incorporating CNCs into PCL and PLA matrices has been shown to enhance key material properties, including thermal behavior, crystallinity, barrier properties, morphology, mechanical strength, stiffness and biodegradability [11].”
Self-citationSheikh, M. A., Acharya, S. K., Sharma, A., Chougule, V. S. S., Singhvi, G., & Jain, A. (2026) · Smart Materials and Structures · doi:10.1088/1361-665x/ae8f8f
“Surface modification of nanoparticles enhances their dispersion but can worsen the synthetic process and raise regulatory issues [133].”
Priwintoko, B., Palanisamy, S., Nugroho, S., Ismail, R., Batcha, A. A., Fitriyana, D. F., Muhamadin, R. C., Siregar, J. P., Palaniappan, M., Karuppusamy, M., et al. (2026) · Polymers for Advanced Technologies · doi:10.1002/pat.70683
“Within PLA/PCL/HA biocomposites, PCL also influences phase morphology, HA dispersion, interfacial behavior, and scaffold architecture, thereby contributing to the overall mechanical stability, degradation profile, and biological performance of the composite system [13, 21, 27, 28].”
Metadata
- Authors
- Ngwenya, M., Gumede, T. P., Pérez Camargo, R. A., & Motloung, B.
- Affiliations
- Central University of Technology (ZA)
- POLYMAT and Department of Polymers and Advanced Materials: Physics, Chemistry and Technology, Faculty of Chemistry, University of the Basque Country UPV/EHU, Paseo Manuel de Lardizábal, 3, 20018 San Sebastián, Spain
- Stellenbosch University (ZA)
- Corresponding author
- Gumede, Thandi Patricia
- Motloung, Bennie
- Venue
- Materials
- Publisher
- MDPI AG
- Published
- 2025-11-14
- Volume
- 18
- Issue
- 22
- Pages
- 5172
- ISSN
- 1996-1944 (ISSN-L)
- PMC
- PMC12654269
- OpenAlex
- W4416199684
- Cited by
- 9
- References
- 93
- Citations by year
- 2026: 9
- FWCI
- 0.52
- Type
- journal article
- Language
- en
- Open access
- gold
- doi.org
- Licence
- Locations
- Materials (publishedVersion, cc-by)
- PubMed (publishedVersion)
- Funders
- National Research Foundation (NRF) Thuthuka Programme (TTK2204264865)
- DSI-NRF postgraduate student fund (PMDS22062125350)
- DSI-NRF Innovation Postdoctoral Fellowship (PSTD2205057154)
- Central University of Technology
- Future Coal Mining
- Topics
- Physical Sciences › Materials Science › Biomaterials › Advanced Cellulose Research Studies
- Physical Sciences › Materials Science › Biomaterials › biodegradable polymer synthesis and properties
- Physical Sciences › Materials Science › Polymers and Plastics › Natural Fiber Reinforced Composites
- Keywords
- polylactic acid, polycaprolactone, PLA/PCL blends, nanocellulose, bionanocomposites, nanocellulose reinforcement, nucleating agents, compatibilizer, nanocellulose extraction, nanocellulose dispersion, mechanical properties, thermal resistance, crystallization, biodegradation kinetics, biodegradable polymers, sustainable biomaterials
About these checks
Registry, retraction, Cites and statistics results are computed, not judged, with one exception: a printed reference that no index lists is read once by a model before it counts as a citation error. Claims are extracted by a model and kept only when their quote appears verbatim in the text; each cited source is then checked, with a model’s help, for whether it says what the claim relies on. Those verdicts can be wrong — read the claim’s quote and the cited source before relying on one.
The claim verdicts this report counts are experimental: their accuracy is not yet measured.
A language model drew the claims from the paper on 2026-10-10, under version 3 of the claim definition (model deepseek-v4.1-flash, prompt extract-v3).
A second model labelled each claim on 2026-10-10 (model jev-1.13-20260917, definition revision gold-guideline-v0.2).
Cited sources are checked with a language model’s help (gpt-6-sol).
Statistics and arithmetic are recomputed, not judged.
Confidence bands are shown only for fields calibrated on our annotated test set. None is calibrated yet, so no band is shown.
What counts as a claim ›How we measure confidence ›How we check this ›
Are you an author, or do you see a problem with this page? Request a review
Data sources
Bibliographic data: Semantic Scholar, OpenAlex, Crossref.
Contains information from the Semantic Scholar Academic Graph Datasets, made available under the ODC Attribution License (ODC-BY 1.0).
Semantic Scholar’s data is described in: Kinney, R., et al. (2023). The Semantic Scholar Open Data Platform. arXiv:2301.10140.